Trying To Get A Free Poulan Pro Chainsaw Running Again.

Links to products I have in my tool bag.
Carb. amzn.to/40x03Yl
Spark Plug. amzn.to/3WDYZ3L
Compression tester. amzn.to/2NMgeze
Spark Checker. amzn.to/3bnXjmA
Tygon Fuel Line. amzn.to/3aCGntm
Carb Adjustment tools. amzn.to/3k7cgxe
Primer Bulb. amzn.to/3dC0WYK
Fuel Filter. amzn.to/2ZC0T7i
DEGREASER www.harborfrei...
....updated 1-28-25
The links above are affiliate links.
Thanks for watching. This Poulan Pro chainsaw only needed to have the fuel lines change, But after inspecting the Carb, It turns out it need more than just that.

[@Mr4squared]

I got this exact chainsaw and a bunch of files,greases and wrenches for $30 in an auction. I find these chainsaws have a lot of complaints on hard starts and bad running. After I got myself comfortable with the parts (courtesy of your videos) these chainsaws are fine once you tune them really well. Thanks for the handy videos!

[@INSIDEHOUSEGARAGE]

yes you are absolutely correct! thank you Mr4squared.

[@LarryHelvick]

the carb is an after market carb. the original Polun carb has a different linkage that does not interfere with the housing. I have a Craftsman Saw that had the same problem and I trimmed the linkage and was able to make it not hang up at idle. I still however with an after market carb

[@LarryHelvick]

was not able to get it to idle no matter how much I adjusted the H and L screw. I ended up buying a rebuild kit for the original carb and was able to get it running probably - good luck

[@robertholsopple9451]

Fixing things allways came very easy to me. It's strange to me that some people cant do these types of things but everyone is good at something I guess. KZbin was a God send to a DIY guy like me. Crazy to think someone messed that saw up that bad then threw it away. They will say "Poulan is junk" when it was their fault it was broke. Good repair video!

[@INSIDEHOUSEGARAGE]

thank you Robert Holsopple.

[@Wanous-hv7zo]

Poulan saws are junk

[@stevenchandler4218]

Good to see that you try not to let anything beat you. Thanks HG

[@INSIDEHOUSEGARAGE]

you bet Steven Chandler!

[@philliphall5198]

I never give up.

[@lewiemcneely9143]

All I can say is welcome to the club. The one I HAD was just like this, new carb and all. I could never get it to open up. When the secondary would start, it'd lean out and die. I bent linkag4es and did everything I could think of except getting out the BIG hammer or cranking the wood splitter. All I can say now is 'Thank God and Greyhound you're GONE' as Roy Clark's song goes. Blessings!

[@INSIDEHOUSEGARAGE]

yes this one seems to be a bit problematic,

[@philliphall5198]

Jet and tinny drill bit

[@lewiemcneely9143]

@@philliphall5198 Give it to the son-in-law and gat a STIHL! That was MY answer!

[@philliphall5198]

Mostly the rubber air boot was leaking

[@rudetuque]

Thanks for the great tutorials... feeling like I am deep in the saw woe weeds right now. But great to see some well laid out camera and voiceover work. And I am envious how easy you are making the tubing onto fittings work!

[@INSIDEHOUSEGARAGE]

Glad to help

[@jameshedrick605]

I have the exact same saw. It's sometimes hard to start but once it starts it runs great. I can tell that looks like an aftermarket carburetor. The original carburetor has a plastic piece that opens the secondary throttle

[@INSIDEHOUSEGARAGE]

yes you are correct, aftermarket carb incompatibility!

[@darrellepickering8433]

If you'll check the parts list from whoever you order parts from they'll likely send you an Chinese-made carb & air valve. Usually the only thing that's wrong are fuel lines & the tank grommet.

[@mickeykim3559]

You are 100% on the mark. That is Amazon/eBay Chinese after market carb for Poulan. They do work well but you have to do some modifications to make it work on Poulan 42cc saw. I ended up shortening the throttle linkage on carb with pliers to prevent rubbing on rubber closing as it was causing throttle to be stuck.

[@INSIDEHOUSEGARAGE]

thank you Mickey Kim.

[@garyalensr]

Well you can tell the person that gave it away or even the person that tried to fix it didn't watch your channel or your videos. All they had to do was watch your channel. Great video and fix!! Can't wait for the next one on this saw

[@INSIDEHOUSEGARAGE]

very true, thank you Gary Allen.

[@crystaledwards1695]

Just getting into tinkering with small engines and things. I found one of these on marketplace for $10 this video was very informative and taught me a lot I didn’t know. Can’t wait to get mine apart and see what I find. Thanks for the great tutorial and tips.

[@INSIDEHOUSEGARAGE]

Glad I could help

[@space4304]

Hello Inside House Garage, I have my first small engine project coming up with my grandpa's old Ryobi 31cc weed eater , this idea of mine came from you because I've always been interested in it since I was younger then I started watching your vids about a month ago and I love how you always explain what you are doing and are very confident about getting every project you do running good. And that brought me the courage to start working on small engines. I hope you can read this and give me some tips on my first small engine project. Thank you

[@INSIDEHOUSEGARAGE]

well thank you Space I appreciate you watching me. As far as tips, Patience, and lots of it. Also don't be afraid to ask questions to anyone, about something you might need some assistance on.

[@thomascrompton7775]

Just worked on my 18 and 20 inch both had issues. Bought full carb kits and actually was the hoses that needed replacing. One hoses replaced run fine

[@INSIDEHOUSEGARAGE]

Very nice work

[@davidoltmans2725]

The throttle interference was exactly what I found on mine just 30 minutes ago. The aftermarket carb looks the same and that rod that is interfering with the cover flashing just as yours. I cut it out to fit and no more binding.

[@INSIDEHOUSEGARAGE]

that works too!

[@deebee3901]

Well done - can't wait for 2nd episode. What I have found out with these cheap replacement carbs is that they lack a lot of torque.

[@INSIDEHOUSEGARAGE]

interesting, must be a design issue.

[@jameshedrick605]

It costs more but i always try and get the OEM carburetor

[@deebee3901]

@@jameshedrick605 not luck with that in Australia.

[@GuysPlayingWithTools]

Good catch. It's not always obvious when the cover is part of the problem. I have run across the "works with the cover off but not on" problem a few times along the way and it's always something different... catching\pinching ubbing\stopping\etc... I would bet a Nickle that the carb he used was slightly different than the one it started with.

[@INSIDEHOUSEGARAGE]

thank you Guys playing with tools, I think this was the first time, I've had to deal with something like this.

[@lewiemcneely9143]

Mine was but .................oh well, it's GONE! YAAAAAAY!

[@GuysPlayingWithTools]

@@lewiemcneely9143 🤣

[@Nukemann64]

This is exactly what I was thinking! The aftermarket carb is just slightly different enough to cause something to bind up / rub etc. And not allowing the engine to work properly. Again, Respect to you IHG for giving it it's fair chance and having a crap load of patience!

[@lewiemcneely9143]

@@GuysPlayingWithTools The son-in-law is a fine guy............and takes every ratty thing I come up with. BUT he's got some nice stuff from here too!

[@MercuryDemers2007]

i've had the same problem with a Poulan predator you need to cut out a piece of the plastic cover, the problem you have is the top linkage will hit the cover and cause the top throttle butterfly to open but not the bottom causing a lean condition.

[@INSIDEHOUSEGARAGE]

I see, thank you for the tip.

[@MercuryDemers2007]

@@INSIDEHOUSEGARAGE no problem

[@MrGattor33]

I noticed the issue with the carb and as I have reviewed and played your video a couple of times I have noticed that the rod that runs thru the brass bushing @ the 8:43 mark appears that it is too straight and needs to be bent outward a bit to clear the rubber seal and the cover a bit. but I did see one gentleman (James Hedrick) state that it is an after market carb and I have to agree; however I think this adjustment may work aside from replacing the carb with an original one. Very good video and rather a puzzling but challenging task. Thank you for this video!!

[@INSIDEHOUSEGARAGE]

thank you for taking a good look at the video and analyzing it, I appreciate it.!

[@MrGattor33]

@@INSIDEHOUSEGARAGE You are very welcome my friend. Again very good and interesting video!

[@INSIDEHOUSEGARAGE]

you're welcome

[@williamsnow1531]

You have more patience than I do. It would of went flying as soon as more problems occurred.

[@INSIDEHOUSEGARAGE]

I hear that, and the thought did cross my mind.

[@Fun4me75]

Good stuff in your detailed assessment and repairs 👏

[@INSIDEHOUSEGARAGE]

Thanks 👍

[@nathancaruthers1720]

Love the longer videos btw

[@INSIDEHOUSEGARAGE]

Typically when it's a full service video, which seems to happen on saws a lot, they're going to be a bit longer than norma, and thank you Nathan Caruthers!

[@gregorydanson3159]

Thank you! I went in search of maintenance (sparkplug, fuel filter, air filter, etc) pieces for my saw, found an inexpensive kit with a replacement carb, I thought, why not. Turns out the replacement carb interferes with the linkages. Old carb is back on again.

[@INSIDEHOUSEGARAGE]

yep the clearance on that side of the carb is really tight for some reason.

[@Jim-ie6uf]

brand new aftermarket carb.. The top cover must be modified to allow clearance for the choke rod. Been there. That's before you revealed it. I had to nip off a fuzz from the choke rod to fix it. I have a lot of ,2 cycle equipment. I Uneathed a 4218AVX, last run Dec of 17. I was emptied of gas, but the carb isn't playing nice. I ordered a Zama carb kit for it. Will be here Thursday. I put that aftermarket carb in another 4218 AVX a few months ago. Not doing it again.😄😭

[@INSIDEHOUSEGARAGE]

Thanks for the info Jim. This might have been a first for me.

[@brianking1138]

I am looking forward to the 2nd video on this one.

[@INSIDEHOUSEGARAGE]

working on the plans now.

[@mattwaters6987]

​@@INSIDEHOUSEGARAGE I'm waiting too! 😊

[@mikesweeney5685]

Great video, just the right amount of detail for somebody seriously trying to fix their Poulan Pro chainsaw - liked and subbed! I have the bigger brother Poulan Pro PP4218AV saw and finally got it to run again after a thorough cleaning of the Zama C1M-W26 carburetor and replacing the airhead body assembly (broken plastic arm), new fuel lines and fuel filter. Oiler isn’t working, I am waiting on a new one to arrive. Question on a compression tester: Several YT commenters on other channels have said the Schrader valve should be closer to the engine cylinder and not at the other end of the hose next to the gauge. Other than needing to pull the starter cord several more times to pressure up the hose, what difference would it make where the valve is located? Anyway, looks like you have a LOT of great fix-it videos. Thanks for sharing them!

[@INSIDEHOUSEGARAGE]

thank you Mike Sweeney and for me, it doesn't matter which compression tester I use, so I completely agree with you about the Schrader valve .

[@brennanschuler]

Had an issue similar a week or so ago with a customers husqvarna. A Amazon non OEM service kit came with the air filter. Said air filter was maybe a thousandth to large on the throttle side and caused the throttle to stick at WOT.

[@INSIDEHOUSEGARAGE]

wow, that's sucks!

[@joebroke76]

Great video!

[@INSIDEHOUSEGARAGE]

Thank you Joseph Brokenbourgh.

[@muletkid7756]

I love your vids

[@INSIDEHOUSEGARAGE]

thanks

[@Rein_Ciarfella]

16:54 FWIW, I don’t care how long or short a video is if it’s well done and addresses an issue completely. I prefer one-part videos that cover everything related to one machine at the same time.

[@INSIDEHOUSEGARAGE]

thank you Rein Ciarfella.

[@tenortrouble]

I just got a 4218AVX from a buddy that gave up on it. Same problem! The carb is supposed to be a Zama W-26 which has a black plastic lever for the top air valve. He actually had the original carb in a box so I could compare and that's how I found it was the wrong carb. Gonna see if there is a gasket kit for the W-26.

[@INSIDEHOUSEGARAGE]

good luck to you .

[@rickthelian2215]

This is where a donor machine comes handy. Maybe the carburettor isn’t correct hence hitting, need to look at PDF of parts for that model.

[@INSIDEHOUSEGARAGE]

I think you're right. thank you Rick Thelian

[@philliphall5198]

I usually replace rubber boot also if it’s over a year old and new home maded carb gaskets These are the best saws if you can do the repairs yourself

[@INSIDEHOUSEGARAGE]

thank you Phillip Hal.

[@electroddxful]

Great video my friend 👍🙏👍👍

[@INSIDEHOUSEGARAGE]

Thank you RayFpv!

[@patthesoundguy]

I have one of those... They aren't a bad saw once you manage to get the carb tuned properly. I find they tend to not be tuned well fr the factory. I am not a huge fan of that model, they have that strange x torq style carb with the top part of the carb for only air. When they work they work well.

[@INSIDEHOUSEGARAGE]

you're right, to be honest, If I need to buy a new saw, I wound't have problem buying a poulan,

[@williamjuraco5180]

Very thorough good video.

[@INSIDEHOUSEGARAGE]

thank you

[@TecumsehRulesbcserk]

I definitely think the throttle linkage is getting caught on something in the cover, I would just cut some of the plastic back or try to modify the linkage so it doesn’t do that.

[@INSIDEHOUSEGARAGE]

yes hopefully I'll get to looking at it soon.

[@mikegrappone9078]

excellent video! thanks for creating.

[@INSIDEHOUSEGARAGE]

My pleasure!

[@MrKeithsplace]

You can’t judge mix gas by color. Just about every brand of 2 stroke oil has a different color or die.

[@INSIDEHOUSEGARAGE]

you are completely right but it's the only thing you have aside from using a fuel analyzer

[@zagatozele]

I just got my hands on a free cub cadet riding mower and it in super good shape

[@INSIDEHOUSEGARAGE]

very nice!

[@Turningwrenches85]

I got the same issue going on also . Look forward to see what you find on it caused the issue , mine is the pp4218a 42cc but same design.

[@INSIDEHOUSEGARAGE]

thanks!

[@Turningwrenches85]

@@INSIDEHOUSEGARAGE your welcome

[@StudCity718]

I found a PP4218avx poulan down the road. All that was wrong was the return line was in the wrong spot and needed a new chain.

[@INSIDEHOUSEGARAGE]

very nice work, thanks for the comment N C (StudCity718)

[@williambray4134]

Parts is the only reason I'd even take one for free. Everyone's mileage will vary.

[@INSIDEHOUSEGARAGE]

I understand what you're saying.

[@ramadinsookhoo6141]

Hey bro, what's up? Shubh Divali to you and your family bro. You got a nice chainsaw with a lot of surprises bro.

[@INSIDEHOUSEGARAGE]

Thank you Ramadin Sookhoo!

[@ramadinsookhoo6141]

@@INSIDEHOUSEGARAGE you're welcome bro

[@adammosher1115]

I literally just fixed my brother's saw it's the same one he got it free and I just had to adjust the screws for it to throttle hi and to idle also the cover on yours is probably a little warped grind that spot where it was rubbing on it

[@INSIDEHOUSEGARAGE]

that's a good idea, thank you ADAM MOSHER

[@shanemobley5825]

I have the 50cc having trouble vapor locking. Runs fine till gets hot. You shut it off it won't start.

[@INSIDEHOUSEGARAGE]

sorry to hear that, have you considered replacing the spark plug?

[@shanemobley5825]

@@INSIDEHOUSEGARAGE I put new pug and coil adjusted low side. Seemed to help some. Even drilled holes in cover over breather to get more air flow. Haven't checked the vent yet to see if it's clogged,but shouldn't be it's only got 2 hrs running on it.

[@ILOVEMACHINES225]

ive had one sitting for 7 years so this may help

[@INSIDEHOUSEGARAGE]

I hope so

[@hosocat1410]

I've worked on several of those small poulan/husqvarnas with the 2 inlet butterfly valve carbs. Very difficult to get them running and keep them in tune. Don't know what husky engineers were thinking.

[@INSIDEHOUSEGARAGE]

me neither but it's what we have to work with

[@jerrysoutherland662]

I had the same issue with the throttle linkage,the cause is the aftermarket carburetor,you have to cut the throttle linkage a little shorter to clear the top cover.THE SMALLERENGINEGUYS video had a video on this.

[@INSIDEHOUSEGARAGE]

Thanks for the tip

[@bobbycrocker9893]

Would you mind posting the link to that video? I trash picked this same chainsaw, and have that same after market carb in the way.

[@philliphall5198]

AllWAYS replace the rubber air boot and save your self a ton of fuel problems

[@INSIDEHOUSEGARAGE]

for sure

[@Glenn_123]

Is there a big difference of 40:1 and 50:1 mix? Some of the mixes sold state that they work for both 40 or 50:1. I love your videos you do a great job!

[@INSIDEHOUSEGARAGE]

to be honest the difference in oil, is so tiny I don't think it matters in the short term. However, I like the idea of having more than I need, so I don't have a problem using 40:1 in a machine that says 50:1.

[@Glenn_123]

@@INSIDEHOUSEGARAGE Thanks appreciate your feedback.

[@Matthew_Does_To_Many_Things]

I run 60:1 in my Husqvarna trimmer and blower. It says to run 50:1 but we don’t feel like mixing more fuel. I use very good full synthetic motocross oil for 2 stroke race bikes. I don’t know if it will make a difference in wear on the engines but hopefully not.

[@2OO_OK]

Was there ever a part 2 to this?

[@INSIDEHOUSEGARAGE]

unfortunately I never got around to it as life sometimes gets in the way. I do plan on getting back to it though

[@2OO_OK]

@@INSIDEHOUSEGARAGE That would be great, your videos are the gold standard.

[@JakeAsencarov-ux3tt]

Hi home garage I have a question so I am fixing my dad’s friends chainsaw and it’s a mcculloch 1422 av and it won’t start and I saw that it had a broken primer bulb so I took almost the entire thing apart to get to it and it doesn’t look like it has any tabs on it that you press on to pop it out and I was wondering if it was possible to just pull the bulb out of the plastic casing that you connect the fuel lines to and then just put the new bulb in please let me know what you think and if it would work or not thanks home garage

[@INSIDEHOUSEGARAGE]

yes you can. I've done a several times. I think I have some videos on here from a year ago when I was doing just that. Hold the primer firmly to keep it from rolling around. Put a small flathead screwdriver tip in the gap between the retaining ring, and the base for the bulb. Pry the ring loose and you'll be able to take out the bulb and replace it. you'll have to glue the Ring back on to the base.

[@JakeAsencarov-ux3tt]

@@INSIDEHOUSEGARAGE hi home garage I am still fixing the chainsaw and I am having a problem with putting the throttle assembly and I was wondering if you knew how it goes back together

[@JakeAsencarov-ux3tt]

@@INSIDEHOUSEGARAGE hi house garage so I got the chainsaw back together and started it up and it worked just fine I just needed to adjust the carb a little bit and then I cut some wood with and it cut fine and then I shut it off and then when I came back to give it a cold start it wouldn’t start and I only changed one of the fuel lines the one going from the primer bulb to the carb and when I pressed the bulb sometimes it would stick inwards like it wouldn’t come back to it original shape and then when I would prime it the bulb would fill up a quarter of the way and then sometimes all the way and my dad told me that it might be that the fuel line that we replaced isn’t sealed around the carb properly but I would like to know what you think so let me know if you know what the problem could be thanks

[@LarrysNo.2Fan]

Where am I able to buy that plastic splice for the fuel tank?

[@INSIDEHOUSEGARAGE]

not sure, I've never had to buy one. TO be honest you don't really need it.

[@dagorithe]

What size fuel lines did you use in replacing the old ones? I have the 42cc version; it looks just like the one you fixed. I can’t complain too much as it was reconditioned when I got it nearly 12 years ago. Mine is giving me a little trouble staying running. I have pulled the carb off and was dirty; the metering diaphragm appeared soft enough to not replace. I think I need to change the fuel primer bulb, so I’ll change the filter and lines as well.

[@INSIDEHOUSEGARAGE]

I used 3/16" line.

[@philliphall5198]

I see a ton of them every year and most likely fuel lines bad and metering diaphragm They run good and really all most folks need It’s all about name games of items

[@INSIDEHOUSEGARAGE]

thanks again

[@Chase_01]

I just got one for free for the exact same reason and I can’t get it to start new carburetor and spark plug still nothing has good compression

[@INSIDEHOUSEGARAGE]

did you check, for spark? I would need to get a compression reading before I would discount it.

[@Chase_01]

@@INSIDEHOUSEGARAGE yes it has spark and it has good compression the unit has only been used twice it’s brand new i took the spark arrestor out of the exhaust too to help it breathe I also run true fuel pre mix 50:1 I’m completely stumped to what is keeping this thing from running explains why it was given to me for free I also gapped the spark plug correctly they should rename these things the pullin pro because that’s all you’ll be doing

[@brianeastman3547]

Does that have a heat shutter

[@INSIDEHOUSEGARAGE]

don't think so.

[@RussellHoughton]

Seams like the new carb is not just right. If it were me I would take a heat gun and move the parts of the cover that'd touching it just a little.

[@INSIDEHOUSEGARAGE]

hey you already know what I was going to do!

[@mattwaters6987]

Is there any update on this project? 🤔

[@INSIDEHOUSEGARAGE]

not yet

[@jamess.putman1779]

That's what bothers me is tge repair shop string. Did they put it back together ,put back all the screws. You never know

[@INSIDEHOUSEGARAGE]

I know right, just slapped it back together

[@jackfrosty79ify]

Bad intake gasket on them saws mine was bad .

[@justincovington4401]

Btw. No video is too long. That's actually what people want is longer videos

[@INSIDEHOUSEGARAGE]

thanks for that, but a long video, could end up taking over well over 30 hours to produce. Having a full time job and a second channel makes that very tough.

[@sammorgan7153]

Is bar upside down?

[@INSIDEHOUSEGARAGE]

you can flip the bar,

[@chrischiampo7647]

Idle Screw Was In Too Far Had That Happen We’re The Choke Wouldn’t Set on an Echo and Shindawa Chainsaws 😀

[@alanlake5220]

Good diagnosis & repair, but the sort of issues you were having with that saw , makes it not worth the time to repair, plus the cost of some of the spares are outragious, just totally unjustifiable, which is why I rarely work on small equptiment any more.

[@INSIDEHOUSEGARAGE]

really? you stopped working on them?

[@robertmailhos8159]

The chain righting mechanism on that machine is hopefully work,s proper

[@INSIDEHOUSEGARAGE]

I hope so too.

[@robertmailhos8159]

@@INSIDEHOUSEGARAGE 👍

[@bertgrau3934]

I had the same problem with mine, I put an aftermarket carburetor on and it did the same thing. I trimed the cover , and it works fine. Mine is the Poulan 16/34 the carburetor look just like my replacement. My old carburetor had a little different throttle arrangement, it had a post that stuck out from the main throttle and it hit the lever for the top air valve. I took the piece off my old carburetor. Not sure if it helped or not. The cutting of the cover seems to have helped more.

[@INSIDEHOUSEGARAGE]

thank you Bert Grau.

[@chrism9976]

Mine started after replacing the fuel lines, idled high like in the video and died as soon as I pulled the throttle. Complete junk. It's sitting by the curb for trash pickup.

[@INSIDEHOUSEGARAGE]

I can understand your frustration

[@garylarson6386]

easy plug the battery in, I love my dewalt 20 volt, and my arm and sholder feel much better

[@INSIDEHOUSEGARAGE]

batteries don't last long, they require special attention, and when you need to replace the, they are not cheap. All these hassle I would keep my ICE.

[@garylarson6386]

@@INSIDEHOUSEGARAGE I bought the 20 volt string cutter so I have two batteries and they seem to last just fine, but I just cut small branches and a battery is same price as hours of gas and oil, the chail saw really did wreck my shoulder

[@verncutshall5950]

What kid or brand oil are ypu

[@INSIDEHOUSEGARAGE]

bar oil not sure, It was given to me, as for 2 stroke it's black max synthetic from wally world

[@mikefuller4539]

Its been 10 month and there isn't a second part for this video?

[@INSIDEHOUSEGARAGE]

unfortunately things have not worked out like I had hoped for.

[@jeffreyhelms9507]

Not the correct carburetor for that saw, I have had that same issue with my poulan

[@INSIDEHOUSEGARAGE]

thanks

[@WhiskeyGulf71]

[01/03/23]What’s happened to this saw since October ?

[@INSIDEHOUSEGARAGE]

it's on the shelf waiting for the parts but they've come in. Just putting it on the schedule. Should be soon though.

[@Rein_Ciarfella]

Once I discovered those first few obvious mistakes I wouldn’t trust anything else to be correct, even if at first glance it appeared okay. That especially goes for what appeared to be a new, replacement carb. So many lacking knowledge, patience or attention to detail throw a new carb at a machine, and in this case it’s consistent with the other things. I would not have assumed the replacement was the correct one and I suspect that is the reason the original cover and inside edges were abraded and cut away - the new carb is the wrong one for this saw. This may explain why the original gasket was incorrect on this carb.

[@INSIDEHOUSEGARAGE]

you are correct, the first few mistakes should have clued me in, that things were very wrong, from the beginning.

[@brucecoleman7412]

Worst case scenario, modify the cover.

[@INSIDEHOUSEGARAGE]

yes that's a good idea.

[@philliphall5198]

Carb gasket wrong one

[@INSIDEHOUSEGARAGE]

it wouldn't start if the gasket was wrong

[@Kyle-bb9zp]

Man what a mess just take it to a small engine repair shop those seam like really good descent chain saw they are like a 100 dollars or 120. Not that i ever owned one.

[@INSIDEHOUSEGARAGE]

that's an idea, but the price for repair would be quite high

[@Bags609]

Poulans get thrown away more than anything. Fuel lines are always junked

[@INSIDEHOUSEGARAGE]

agreed

[@hosocat1410]

Poulan is the most troublesome, unreliable saw on the market. Husqvarna should be ashamed of themselves for producing it. Pay a few dollars more and get an echo or a stihl.

[@INSIDEHOUSEGARAGE]

they definitely have their issues.

[@andreworli4117]

What with all the shoddy maintenance issues isn't it conceivable that the previous owner bought the wrong replacement carb? You shouldn't have to cut away seals and housing to make the machine operate properly.🤔🤕

[@INSIDEHOUSEGARAGE]

I know right, something seems wrong

[@jeffreyhagelin3672]

That's the classic sign of an air leak when you have a high idle like that Still way too lean I will double check those rubber boots that you replaced for air leakage.

[@INSIDEHOUSEGARAGE]

thanks

[@jackfrosty79ify]

I like the 50cc better .

[@INSIDEHOUSEGARAGE]

wow, nice, I've got to try and find one.

[@bjusticeforever]

I had to cut the linkage on the tip where it was hitting the plastic cover. Break out the Dremel, baby! The Chinese replacement carbs apparently all have this issue; Amazon shows several images of people who had to do the same. Very poor craftsmanship.

[@INSIDEHOUSEGARAGE]

you are correct, the linkage was hitting the cover

[@SHOINOFF]

Lol what i would give to drive 20 miles in 30 minutes. Here i drive 25 miles in 2 or 3 hours.

[@INSIDEHOUSEGARAGE]

wow!

[@SHOINOFF]

@@INSIDEHOUSEGARAGE lol yeah bro, miami florida.

[@williamcarl4200]

The original fuel looked like motor oil/fuel mix. This is never a good option.

[@INSIDEHOUSEGARAGE]

correct

[@johndowns7536]

Your skills are wasted on this POS machine. A helpful video.

[@INSIDEHOUSEGARAGE]

some folks simple can't afford to buy a new saw, so this might help them, and thanks

[@richardo6357]

Throw it back in the trash. Pullons suck. They run for one job and then never start again. Buy Stihl and they last forever and start every time.

[@INSIDEHOUSEGARAGE]

so I've heard

[@dylanowens3173]

Unless it is a high quality name brand chainsaw it is not worth fixing even when free. You are fixing something that is not worth it but for your own knowledge. In 2023 I bought off Craigslist two saws new in box never used $80 each. A Poulan 42cc 18" & a Walmart black max 50cc 20" , both never used were gifts they didn't want.

[@INSIDEHOUSEGARAGE]

you have a good point and thanks for sharing that story

[@Wanous-hv7zo]

Saws are junk

[@INSIDEHOUSEGARAGE]

they all can be

[@Wanous-hv7zo]

@@INSIDEHOUSEGARAGE poulans are junk and you know who owns poulan? Husqvarna and their saws are poor quality too. I own a saw shop in have fixed all brands

[@MrKeithsplace]

It’s a Poulen, it could many problems, I hate their stuff, IMO mostly junk.

[@kevinpowell4182]

what a piece of junk never been a very good brand.

[@scottseal418]

They put wrong carb on ran into problem today

[@INSIDEHOUSEGARAGE]

correct