Turbo Oil Line INSTALL

vid on how to install a turbo oil line on my FGX Ford Falcon
Music:www.epidemicsound.com
Parts:
antzperformanc...

[@PAYNE098]

Mate awsome video, very clear to see everything needed to get this done. 👏

[@johnsonwithat2322]

Thank god I found this. Now I can go in with a bit of confidence

[@ajlarkingarage]

I hope it helped

[@LennyMill]

Did you remove the filter from inside of the union bolt? The part the banjo bolt attaches too? Thats the part that gets blocked.

[@shanepasco3827]

I didn't see you pull out the factory filter

[@ajlarkingarage]

I forgot to film it mate didn’t realise till I finished everything

[@NAH7Z]

this might be a stupid question.. before connecting the other side to the turbo etc, how did you get oil to go through the line? did it just gradually do it because of the oil pressure, or did you just crank the car a couple times to get it to flow?

[@ajlarkingarage]

To get the oil thru leave the line off and crank the engine over if you don’t want it to start you could unplug the crank angle sensor or unplug injectors or coil packs And just keep cranking till the oil comes out

[@NAH7Z]

@@ajlarkingarage aight sweet, cheers mate, helps heaps

[@1993kawasaki]

all you do is hold the gas pedal to the floor and crank it, the car wont start, well thats on the ba bf models..

[@levi-hi8og]

hey man did u put the externeder thing from the turbo before or after the fitting given by antz, thanks

[@ciaransvloggs9619]

You didn’t remove the original filter in the side of the block

[@ajlarkingarage]

I did I just didn't film it I explain this in another vid cheers for your concern but 👌🏻

[@bigpole6715]

So now do you just have to clean the filter every service?

[@ajlarkingarage]

Correct

[@Aaron_willis14]

So the stock filter is in the block behind the feed line hey? Do you just unscrew it and pull it out? Cheers.

[@ajlarkingarage]

Yea mate just unscrew that fitting and the filter is inside the fitting and will pull out 🤙🏻

[@Aaron_willis14]

@@ajlarkingarage cheers mate. Just fitted it. Worked well. Thanks for you help.

[@ajlarkingarage]

ADVENTURE_WITH_US sorry for the late reply mate 😂

[@justkyddingracing9268]

@@ajlarkingarage problem is you didnt remove factory filter in the vid

[@goldberg7995]

Are you gonna end up throwing gauges in mate? Would love to see a video on how you do it. I’m buying an fgx sometime this year and I can’t wait

[@ajlarkingarage]

I’m gonna get triple gauges eventually but just gotta save some $$$

[@samgordon7616]

Dumb question, but when you're making sure you've got oil flowing through your new line, how do you get oil coming through without starting it? Cheers

[@ajlarkingarage]

You can disconnect a crank angle sensor or just have the line going into a Bottle and turn off the car as soon as the oil comes thru

[@Raffmeowmeow]

Hey mate did you pick out the internal filters from the factory fitting so that it's free flow.

[@ajlarkingarage]

Yea man I did, I recorded it but the footage was all munted and by the time I was editing I realised I forgot to mention it!! lol rookie AF

[@dionjayw]

@@ajlarkingarage you can edited after its been posted on KZbin now, and just write it as a caption note at that point in the video

[@ajlarkingarage]

@@dionjayw I did not know this I'll get onto that asap

[@damienchatys844]

Dumb question what socket size did you use to Remove the oil pressure sensor

[@MrBrooxy]

Deep 21mm I think it is

[@brynmorgan5082]

Have you done valve springs?

[@ajlarkingarage]

Not yet on my car, but I do have a video on the channel about doing them on our turbo AU build

[@elliotbarron4913]

Heyy mate, if you want to tidy up the look of the filter ie how its sitting you need to go get a -04 m12x1.5 fitting which will allow you to screw the factory extension piece so the kit can sit how its supposed to, i had the same issue and it played with my ocd sumin shockin haha

[@ajlarkingarage]

Elliot Barron bro thanks so much I went back and forth with antz about the way it fitted, I’ll get that fitting.

[@elliotbarron4913]

@@ajlarkingarage yeh no worries bro, there kits are based off another brands kit and the fitting supplied is for an fg f6 or b series turbo not the little 76 baby turbs haha, i have notified antz so they can rectify the problem

[@eamonholland4960]

@@elliotbarron4913 bought one recently haven't rectified the problem

[@elliotbarron4913]

@@eamonholland4960 thats shit bro, i personally spoke to oldmate who owns it and he said it would be fixed 🤷‍♂️ if you get that fitting i mentioned itll all work n look tidy

[@ziyadhouzaife1102]

How do I open it to clean it? The filter in the middle

[@ajlarkingarage]

It unscrews

[@mrngreenthumb]

sealant is defiantly a bad call on line in to turbo bud!

[@sammydpeters]

One bolt and that stock line comes out without bending it

[@ajlarkingarage]

Oh dear, bit late now 😂

[@brokenlegz]

What bolt?