Turning Stainless Steel Bolt into Useful Pneumatic Tool - Air Graver without Lathe Version - 2

[@wirekat]

Excellent work. A true craftsman doesn't need high priced machines.

[@floydc3664]

Your craftsmanship is amazing, it was a pleasure to watch you work.

[@ambroscustom]

Thanks you sir 🙏, appreciate your feedback, means alot to me..

[@nothsim]

So happy to know that craftsmen like this still exist

[@ambroscustom]

🙏your words means alot to me sir.

[@keycommander971]

Love this can’t wait to buy a lathe when I have the money this is the first thing I’m going to make. Been wanting to engrave for about 2 years now but the machines are so expensive 👍🏼

[@ambroscustom]

Thanks pal , well currently without lathe it's extremely time consuming process to make and I am too going to wait for lathe to mass produced these some day and in meanwhile I am going to fine tune this for much better result.

[@ajay60486]

hello sir pls tell me how can i buy this pls reply me

[@wolfey24k54]

your skills outmatch your tools by a long shot. you just did machining with garage sale Bargen bin (no offence you do have some very nice ones but you made due) tools. and destroyed it not by a little but a long shot. such an amazing piece of craftsmanship not for the budge but for what it is.

[@monder3259]

Amazing work! Your skill is unbelievable. Thanx for a great video!

[@ambroscustom]

Thank you for the generous words 🙏

[@ToolsandTime]

Pretty incredible work to do without a lathe, well done!

[@ambroscustom]

Thanks mate 🙏

[@bespokerodsandblades]

Man, you have my greatest respect! Your skills, knowledge and imagination are endless!!! Amazing work!!!

[@ambroscustom]

Thank you for your words🙏.

[@bespokerodsandblades]

@@ambroscustom As I said before - great job! Could you tell me what compressor you are using? What pressure is needed for the graver to work? I wonder if your graver could have been powered by a compressor from the refrigerator? Because the compressor from the refrigerator is very quiet .... I will be grateful if you give me a hint. Cheers :)

[@ambroscustom]

Thanks again brother, so for this perticular graver i am using simple 30l shop air compressor. It's extremely loud. Usually the pressure needs around 2-3 bar, but due to my precision i need to use 4 bar to make it work effectively. I heard about the refrigerator compressor but never had a chance to work on that. If you are willing to make this then definitely give it a try. It's my pleasure to help you out.

[@ElTallerdeSanti]

Felicidades por tu trabajo y tu dedicación, disfrute mucho mirando tu video y el trabajo final es excelente, un saludo desde España.

[@ambroscustom]

Thanks brother, glad you liked it.

[@coffeecuppepsi]

this is truly amazing.. awesome work bro

[@ambroscustom]

Thanks for the words mate🙏

[@snobanker1]

I am in the process of making one of theses graver hand tools. I was making the piston and trying to figure out the location of the perpendicular air hole in it. A quick glimpse of your digital calipers shows the measurement of 10.45 MM and it appears you mark the location measured from the narrow tip of the piston. In later pictures it definitely looks like your air hole is closer to the thick end of the piston indicating the measurement was from the tip. When I duplicated that on mine there was no way the air hole could go past the internal stopper when the graver holder was inserted without having it adjusted nearly all the way out. I decided to switch the measurement from the other end of the thinner part of the piston where it meets the thick end making my air hole 10.45 MM from the base and closer to the tip instead. That seemed to work and now the graver operates with tip even fully inserted. I was curious if you had made the hole different in your working graver or was I just seeing it wrong. By the way, your tutorial is great, luckily I have a small lathe though lol. Great job!

[@vagishgpatil3013]

When ready made Tools cost less than Making one ,People Find it economical to Buy one ...... but When It comes to Turning a scrap Metal into a final product You owe My respect bro.. that's Amazing..,indeed your dedication is So High..I ENJOY watching Metal working Videos a lot..I have come across negligible Indian Machinists On KZbin....I am so lucky to find You ..When I watch Videos of Ahmed(blacksmith),Adam,ori,Tony . Sometimes I just can't connect with them in one or the other way..Their language, Accent, technical terms are quite hard to understand,thats because Most countries use imperial system,,But here We Mixed all things up.. Imperial ,Metric ,Indian Soot System etc. 😁.. .Keep up the Work.. Honestly, you should build your own lathe But only Drawback would be automatic Rack Motion,Speed gears, threading Are the few to mention..,But If you relie on Taps And Dies for threading.You should go for it...

[@ambroscustom]

Thanks for the words brother, yeah I am planning to buy a lathe pretty soon. I think making a lathe isn't going to be that precise and thanks for being a loyal subscriber 🙏.

[@roadshowautosports]

So, I see you’ve started this project when you were a kid! Stainless steel machine by filling only? You’re a brave man!!!! I’m afraid to cut it on my small lathe!!!! How long it took you to finish this project? Good bless you for sharing such a WORK of art, and emphasis on WORK !!! Happy holidays!!!

[@ambroscustom]

Thank you sir for the words, the total time it took around 12 days working 10-12 hr a day. It's not fixed but roughly that was the timing. Definitely a time consuming process since after every minute i have to stop it and measure it. But the rattling sound makes that time worthy enough of every hour. Thanks for giving your time:)

[@roadshowautosports]

@@ambroscustom i imagine and admire your talent! I can’t imagine how you got such tight fittings by hand but lots of respect for you indeed!

[@roadshowautosports]

@@ambroscustom wow! I imagine it was something in those lines as it is such a great piece! Most amazing is your kindness to reply to us! Thank you so much for all you do for us!

[@ambroscustom]

thank you sir for your kind acknowledgement. I means alot to me 🙏.

[@alierem4266]

Dear Ambros. Have u by now arranged a lathe & have any modification(s) been made to your hand made piece pl?

[@Podshans]

Моё почтение, вытрчить такой инструмент помощью только дрели!!! 💪👍

[@munaemkhan1952]

Good. Very nice work . Please one video engrever compressor

[@pedrotome9119]

Hello. I borned Portuguese, and they have this old saying: - "A guitar need to be in the hands of those who know how to play it properly". Well, I do similar jobs trying to repair the daily destruction our pupils do everyday, with everything at the public school I work.😢😢 And here I see one more time, how much I still need to learn!! Uau!! 😮😮❤❤

[@chetan.gondaliya]

Wow you're genius

[@IgorKarasenko]

Great work! Do you have plans with measurements for it?

[@ambroscustom]

Thank you, mate there is a Russian video who mentioned the drawing in his video, at present i didn't have that link but you need to search on KZbin about graver and in suggestion videos you will find his channel.

[@이종현-m1k]

인정 장인 입니다😊

[@Streetduck]

Hi, hast du davon auch einen Plan mit bemaßung? Wäre toll 😉👍🏻

[@Streetduck]

🧐🥴🤷‍♀

[@chrisgenovese8188]

What a lovely hand piece! I like how you angled the air valve parallel with the piece, instead of it jutting out. Looks like it fits nicely in the hand.

[@alierem4266]

This configuration assist air pipe to remain intact as it is being held in the hand. Great work.

[@rajvirsingh4558]

ਵਧੀਆ ਕੰਮ ਕੀਤਾ ਹੈ ਜੀ 👌👌

[@ambroscustom]

Thank you paaji

[@bartmaenhoudt3122]

indeed very nice work, proves the need of costly machines is not realy nessecairy, determination and skills are, but i always heard stainless steel is more prone to seizure for 'running surfaces' (sorry for my poor englisch)

[@ambroscustom]

Thanks for the words sir🙏, appreciate the feedback and your English is good:)

[@shinecustomstravisswedziak8814]

So the the piston goes up and down based on pressure at first, then as the compressed air rushed out the 6 exhaust holes creates a low pressure which draws the piston back down? I’m struggling understanding the continuous motion. The piston ends and the air inlet measurement must be extremely crucial. I get the concept but very tough to picture.

[@ambroscustom]

Yes dear you are right, sorry for the late response.

[@chandramohank9743]

Can you sell this good palm control? ...

[@keithstanley2007]

Can you please post a link to how you made your compressor please? Thanks!!!

[@ambroscustom]

Dear this one has normal air compressor. There is no modification required. Search same title on KZbin and you will find another design of graver with modified compressor. For detail information about modifications of compressor, search shaun hugh. He explained every step required for the modification. Or you can search the same title over instructables and you will find design files and dimensions. If need any help please let me know.

[@ambroscustom]

kzbin.info/www/bejne/fZW3aJuDi8SWnNE Here is the full link of the video made by Shaun hugh

[@keithstanley2007]

EXCELLENT!!!! How long was the M20 stainless bolt please?

[@ambroscustom]

Thank you, they are 80mm long

[@pacosambuco1686]

Desdé luego amigo un trabajo de cojines,es impresionante el trabajo qué hacés,sigue realizando muchos más trabajos cómo éste,yo té escribo desde tenerife,( islas Canarias, ánimo)

[@puneettyagi8803]

Amazing work 👍👍

[@keycommander971]

Next I watch to see a showcase watch lol 👏🏼👏🏼👏🏼👏🏼

[@keycommander971]

How much u selling it for

[@vikas90584]

Sir can sher the dimensions and size..

[@liamterlouw2755]

Can i buy one of these

[@arelgr9407]

although I have doubts about the end result using non-precision tools such as without a lathe. the process is of course the same and watching the presentation is enjoyable because of this difference.

[@ambroscustom]

Hahahaha.....not surprised by your words brother, the tool is working fine but definitely not perfect as it needs to be and there is nothing astonishing in making a graver by drill press and drill machine because in the end all you need is a straight hole in the shaft. Thanks for giving your time to see the video:)

[@arelgr9407]

@@ambroscustom alas and me to thank you for all.👋🙂

[@nimalamarasiri5452]

Do you sell on of these?

[@ambroscustom]

Yes, first month of January I am going to sell a batch of 10 PC's. So stay tuned.

[@freelancerider100]

Brilliant! Thank you.

[@Hopkinsg1]

Hi, Do you have to retrofit your compressor to push and pull with this engraver or does the piston change direction due to hole placement?

[@ambroscustom]

Yes the piston hole changes the direction. The first one you are talking about is a different design in which compressor needs to modify so that it can do suction and compression.

[@Hopkinsg1]

@@ambroscustom Ok, thanks. Does the 5.97 mm part of the piston slide into by the 6 mm hole in the spacer. And does the larger part of the piston strike the spacer to provide the forward Hammer thrust. If not, where does the piston strike. Sorry for all the questions.

[@ambroscustom]

@@Hopkinsg1 yes 5.97mm part of piston slide into the spacer hole. The piston didn't strike the spacer infact the air coming from the compressor creates a cushion underneath the piston and spacer which lift it again for the another strike. The piston actually stikes with the graver holder. If the piston stikes to the spacer it will going to jam. So make sure to have pretty tight tolerance. I failed 3 times due to piston since I didn't have lathe and due to that accuracy affected and don't be sorry brother, your questions are welcome.

[@Hopkinsg1]

@@ambroscustom Thanks again. I may need to ask more questions when I am making the engraver.

[@stefchiundo]

De donde eres los vendes necesito uno

[@ambroscustom]

Soy de la India, planeé venderlos y actualmente estoy restaurando un torno viejo para una producción fácil. No puedo decirte la fecha exacta.

[@stefchiundo]

@@ambroscustom ok esperare

[@domm5715]

I did it!!! Works like a charm, it took awhile, but i learned allot and definitely upped my metalworking skills, thx so much for your vid and your help thu email...you sir are a boss

[@ambroscustom]

Pleasure to hear that mate. 🙏

[@sv2tw]

EXCELLENT!!!!

[@ambroscustom]

Thank you sir

[@tnt423]

Ole, ole y ole 👏🏼👏🏼👏🏼👏🏼👏🏼

[@ambroscustom]

Thanks bud:)

[@coulterjb22]

Impressive!

[@keycommander971]

😂😂😂👏🏼👏🏼👏🏼 who needs a lathe just started to watch it 😂😂😂

[@altuhow.waleri]

Здравствуйте скажите пожалуйста сколько стоит полный комплект для работы в рублях

[@ysmwelds1791]

Hey buddy your 100 vedio was coming please now you make to many types t tig torches

[@ambroscustom]

Dear custom made or homemade torch cost alot more higher than what actually available in the market. So that was a bit difficult this time, so extremely sorry for that.

[@mr.konservator]

есть такая штука, называется "труба"

[@xFR34KEEx]

You need a steady rest. Still fantastic work.

[@ambroscustom]

Thanks for the words, yeah that will definitely make that grinding part little better and easier.

[@СлайдТ]

👍 Молодец.)

[@dineshsakthivel7925]

I need this tool for my work I search to online shop but i can't find it. Can u sell this product

[@ambroscustom]

Only made on order and price is 32000

[@dineshsakthivel7925]

@@ambroscustom full set of tool 32000 Or this engraver handle 32000

[@ambroscustom]

@@dineshsakthivel7925 dear it's only the tool showing in this picture with pneumatic pipe and fittings so that you can connect to your compressor and two sets of engraving bits, that's all. You need to buy an air compressor by your own.

[@alexnikoo244]

You will make it with lathe much better than this ❤

[@ambroscustom]

Yes, lathe brings alot more stability and less failure. Thanks for your time.

[@2ndAmendmentMF]

Final boss

[@Apjwellerschennai]

I want 2 pc

[@craftsmanengineer336]

You need a lathe

[@m.m.rengineering196]

Not baad

[@이종현-m1k]

❤❤❤❤❤😅😍😊👍👏👏👏👏👏❤️‍🔥😭😱

[@nusberg9300]

❤❤❤👍👍👍👍🙏🙏Привет из России 🇷🇺

[@юрийдадов]

коту когдо не чего делать он яйца .........

[@stephaniedill9966]

Impressive!

[@hotcoffee5542]

Impressive!

[@ambroscustom]

Thanks pal.

[@alierem4266]

Most imoressive.