Пікірлер
@manuelfhddhdghfgh 4 күн бұрын
Amazing job ❤ can you please share the design ?
@ramyhaddad4770 5 күн бұрын
Can I use 1/4 inch solenoid?
@Ghost_DIY 7 күн бұрын
Can you give me high frequency starter install digram. I have a doubt whether high voltage will damage the welding machine
@قاسمالخرفان 9 күн бұрын
هذه الجره اوكسجين او غاز طبيعي ارجو توضيح هذا الامر
@LittleGreyWolfForge 17 күн бұрын
I was expecting a half assed video. This was very professional and extremely helpful. Thanks brother!
@mikefennema5561 19 күн бұрын
What polarity are you using?
@usnchief1339 22 күн бұрын
Thanks for the demonstrations
@ArminArbi 23 күн бұрын
به عنوان یک همکار میگم عالیه ولی چرا با جوش TIGنمیزنین
@TaskForce141cod 23 күн бұрын
that's why I prefer gas welding instead of electric welding; bright light and smoke
@aligolestani904 26 күн бұрын
Very good👍👍👍👍👍
@deacdaniel6425 28 күн бұрын
Hello, what do you think of the e6013 electrode, 1.6mm for sheet 0.8-1mm?
@hackkingnexus Ай бұрын
Is it permanent or temporary
@RyszardKowalewski-r2c Ай бұрын
Great 👍
@AliHaider-wi6lo Ай бұрын
hello brother how are you which you have made using plastic to place the tools Is it possible to get a picture of the Najabis? I am from Pakistan please I need money for tools help me
@pauljohnlongua4093 Ай бұрын
I imagine there is a kiln where the temperature is programmable, so you don't have to worry about overheating? But hey, your results are beautiful.
@pauljohnlongua4093 Ай бұрын
You really should edit out the tutorial on how to operate a torch. But hey, your results are beautiful.
@ralphnewcomejr Ай бұрын
You do a Damn Good Job with those 2.0 mm rods! 👌
@siddheshmundhekar1330 Ай бұрын
Can electrode toch into the ground.
@EdCuyler Ай бұрын
Good video, can I use older AC welder with SS?
@nephilimshammer9567 Ай бұрын
Could you not oven these
@stefanm5636 Ай бұрын
Thank you for sharing this idea with us!
@Shoukathali-w2c Ай бұрын
S/ face milega
@Shoukathali-w2c Ай бұрын
Yea s/face
@genovevavincent4219 Ай бұрын
Please can I get those equipment and the colours?
@genovevavincent4219 Ай бұрын
Great technique
@WINSCOMETAL Ай бұрын
❤❤❤❤❤ Professional and fine workmanship, the owner of the video is a person who is focused and loves life!
@JánTkáč-r7z Ай бұрын
thank you
@bachelordropout4949 Ай бұрын
New sub❤
@sohaibkhan3426 Ай бұрын
Bahott hard❤💥🔥🔥
@asanga374 2 ай бұрын
Which steel are you using…
@ambroscustom 2 ай бұрын
This one was made up of high speed steel bar. Not recommended to use since it's way too hard.
@kyungsoonpark7118 2 ай бұрын
Coool
@diegojorge9659 2 ай бұрын
Wow! This is asesome! Can you polish it aferwords keeping the color or it wash away? And it keeps the stainlless propeties? Thanks a lot!
@rabbitvtwin6434 2 ай бұрын
🍻🧐👍🏽 excellent video! Thank you 🙏🏼
@karankapoor001 2 ай бұрын
Sir ji,,jo alang to machines buy kitiya ohdi detail videos kado banaoge?
@ambroscustom 2 ай бұрын
Ek video pavage veer ji. Regarding update. Kithe tak restore ho chuki ne.
@jedgurley 3 ай бұрын
OMG... Look. This is probably the most dangerous welding you can do besides MIG on stainless steel.. you do know you are exposing yourself to hexavalent chromium! It's carsonagenic.. 100 %. It will cause cancer.. period! There are companies that won't even let you weld mig of stick weld stainless unless covered in a suite...... For real , before you try this stuff research first . Safety first. I have worked in welding for over a decade with college.. don't do this. Please
@alevans51 3 ай бұрын
This is so sad.... Reminds me of the song, "If I Had A Hammer".
@hanafitan-q4o 3 ай бұрын
ngeri amat pake oksigen ?
@a.o.3523 3 ай бұрын
How do you make the red color?
@bryco32 3 ай бұрын
Damn fine job Men!!!
@JerryFleck-zp3xy 3 ай бұрын
Thanks for the good video, now I'll know more about how to weld stainless exhaust pipes, need exp.
@unameitiuploadit8902 3 ай бұрын
3:54 WOW SUPER COLOUR
@sareythun69 3 ай бұрын
How much for temperature for extruded?
@robthysoul 3 ай бұрын
How long do the colors last?
@positibongachannel3561 3 ай бұрын
what a nice craftmanship
@biakthuamipachuau4073 3 ай бұрын
Im your new subscriber form northeast mizoram..please tell me What angle grinder disc do you used for cutting out the shape of that tanto knife?
@geneautry2091 3 ай бұрын
I'm not fully equipped to GTAW or GMAW, only FCAW & SMAW.
@geneautry2091 3 ай бұрын
Your illustration gave me the confirmation I need. I have a DC output 140amp multi welder I use here now.
@geneautry2091 3 ай бұрын
I'm AWS D1.1/5.20 "unlimited thickness, 3g4g (all) since mid 2006. I've been ASME years 30 years. Anyway, I've an old MWD (measurement while drilling) brass buckle I've had since '86 that has broke a leg off the buckle. It's a single hook not the common latch. It's a really nice buckle. I am oilfield trash.
@metalnascher9995 4 ай бұрын
Awesome technique brother!! Love it
@thelastgs-pian9965 4 ай бұрын
what is the gauge of the tubes used , 18 gauge is max what i get here and i always blow them when welding...
@ambroscustom 4 ай бұрын
These are 3mm tubes