tutorial on Vivado XADC by creating an FIR filter on Basys 3

[@cooperchaopingzhang4008]

Excellent, Professor! This tutorial is worthing much much more than many many useless lectures!!!

[@salamelahmadi]

Nicely done Vahid!!! many thanks.

[@emadmojaveri1404]

thanks dear prof. Vahid, it was really helpful

[@shahrzadpmd9905]

Thank you, this is really helpful!

[@Kianam2]

Great video 🙏 you saved me

[@ericprebys7936]

Thanks! This series of videos helped me do a similar exercise in my class. I was having a heck of a time getting the XADC interface to work. It seemed like the magic bullet was tying the eoc_out() to the den_in(). I'm not sure I fully understand that. Does that latch the value through on the edge?

[@tempusFugit1337]

Hi Vahid, i understand why you do a shift of input values by 3 bits to divide by 8 but why do you cut 3 bits from the output values by doing "dout

[@vahidMeghdadi]

Hi, because I needed just to 12-bit resolution. That's why I took the 12 MSBs. So in fact I discard the 3 LSBs.

[@user-bw8jf2tn7q]

Sorry, I'm so beginner. So , I would like to know how to connect the FPGA terminals to the analog discovery terminals.

[@josemedina7780]

Hello, the link of the file Beasys not is available, Please help me with the files please. Excellent video. Thanks.

[@vahidMeghdadi]

Sorry, here is the new link www.unilim.fr/pages_perso/vahid/XADCinBasys3.html

[@ishanprabhu8904]

Which algorithm is used for designing?

[@brajkishorrajput9238]

can you do coding in 3-tap FIR Filter

[@qwerty123456789690]

is xadc on chip adc in xilinx fpga board ?

[@vahidMeghdadi]

Hi, it is inside the Artix 7 FPGA.

[@5minutething519]

@@vahidMeghdadi Ok thanx. Yes i saw in basys 3 , artix 7 based board

[@allhero4128]

Where is ip block ?

[@jiren_bbx1970]

Hello there, thnx for the video it's very intersting. I was wandering if you could help me because i'm using the same FPGA board (basys 3) and my goal is just to read an analog input and eventually display it in the seven seg display but i m just a beginner so it would be very cool if you can help me. Thnx again

[@vahidMeghdadi]

Hi BI MO, you may take a look at www.unilim.fr/pages_perso/vahid/VHDL/XADCinBays3.xhtml. I put a detailed usage of the XADC that may help.

[@jiren_bbx1970]

I did everything it said but it shown me some errors i didnt find answers to, so it s not working at all

[@jiren_bbx1970]

@@vahidMeghdadi Hi again, it worked perfectly but can i display the voltage in the 7 seg display ? Thank you so much for your help

[@vahidMeghdadi]

@@jiren_bbx1970 Look this link www.unilim.fr/pages_perso/vahid/VHDL/afficheur.vhd

[@firashammad5775]

Content is good but very hard to hear because you are whispering.

[@brajkishorrajput9238]

simulation in vivado

[@firashammad5775]

Audio is terrible

[@vahidMeghdadi]

Sorry for that ...

[@Ankitsingh-my1vu]

What was the end waveform software that you used ?

[@vahidMeghdadi]

It is the tool "WaveFormes", by Digilent. I used also the discovery 2 board as signal generator and oscilloscope.

[@Ankitsingh-my1vu]

@@vahidMeghdadi oh thanks