Two Stroke Pipe Dent Removal | You Never Forget Your First Time

Рет қаралды 27,079

Seat Time

Күн бұрын

Пікірлер: 43

@C3Enduro Жыл бұрын

Just picked up one of those kits and will try it out this weekend. Thanks for the vid!

@SeatTime Жыл бұрын

Good luck and let us know how it goes!

@adewhite731 6 ай бұрын

Excellent video. Nice time saving edit with the simultaneous intro/setup. ❤

@SeatTime 6 ай бұрын

Thanks! I'll have to rewatch it and see what I did to make it helpful, but short, ha! Enjoy #GettingSeattime & Stay #Stoked! 🤘🏻🤙🏻⚡️

@dahatchery 2 ай бұрын

Great job! I do it that way on all my YZs.

@SeatTime 2 ай бұрын

Thanks! 🤘🏻🤞🏻⚡️

@dannyarcher7015 Жыл бұрын

What sort of torch should be used please? Propane? Apparently Butane won't heat the pipe enough.

@SeatTime 11 ай бұрын

I started using MAP because it burns hotter. Good for metal on the bike and bearings, worthy of being cautious when using it in the pipe (thinner metal)!

@dylanmooney787 Ай бұрын

Yeah i don’t think i’ll ever forget my first time. I made a homemade tool to seal the ends and it blew off, still unsure if i got compressed air under my skin 😬

@SeatTime Ай бұрын

WOW! Using this tool scares me enough. I don't think I'd EVER try a home made version of blowing out a pipe!!!!!

@lostinpa-dadenduro7555 Жыл бұрын

There is a kit which uses water instead of heated air. It’s way safer. Hydra Force.

@SeatTime Жыл бұрын

I’ve seen it, and want to give it a try. But I also had to try the more dangerous version as well!

@tonyscaglione1146 4 ай бұрын

Does the blue outter line around the dent from the heat end up disappearing or does it stay there forever

@SeatTime 4 ай бұрын

Sometimes you'll see them fade away, but I typically see them to some degree after blowing out a massive dent.

@didumss 5 ай бұрын

Hey team do you have to take the pipe off to be able to heat and pop the dents out or can you leave it on the bike while doing it? Thanks!!

@SeatTime 5 ай бұрын

You’ve got to take it off so you can cap off the end. Whether using water or heat, you’ll need it off the bike.

@laneconaway780 Жыл бұрын

super sketch! and helpful.!

@SeatTime Жыл бұрын

haha, dude, SO SKETCHY! And I already have to do it again :|

@Danman1972 Жыл бұрын

Maybe a body hammer would work with those little dents. The pointed side is for shrinking metal. That body and metal bending is hard to master from what I've heard. Done some cold bending and have straighten a sub frame from a loop out. Its hard!

@SeatTime Жыл бұрын

I think you're right. Maybe for the next pipe I'll get a bi more crafty. Hopefully I don't blow anything up... 💥

@TheChaz81 Жыл бұрын

Damn looks cool! Was the process add heat add pressure add heat add pressure until it popped back?

@SeatTime Жыл бұрын

That was the process in the beginning. On the later on dents, I started bringing the pressure up to about 70-80, heating, and if I really needed too, adding more pressure up to 90psi. I REALLY didn't want to go over 90psi...

@TheChaz81 Жыл бұрын

@@SeatTime so boom straight to 80 and heat. Then at 10 more on the tuff ones!

@SeatTime Жыл бұрын

I don’t know that it’s that cut and dry, but maybe it’s a good place to start. The small, sharper dents were certainly tough to get out. I feel those might need a bit more love and finesse.

@TR-cs4tf Жыл бұрын

What is the name of the kit you purchased?

@SeatTime Жыл бұрын

Two Stroke Pipe Repair Kit Link: www.ebay.com/str/rjsumnermanufacturingllc Here's the post when I got it in. instagram.com/p/CtaHwJNAlDa/?img_index=1

@dorianrodriguez7591 11 ай бұрын

Where can I get this tool any link ? Yz85 2022 here

@llama3512 3 ай бұрын

you’re removing the dent and I’m trying hard to dent mine for clearance 😂

@SeatTime 3 ай бұрын

🤣 sir, I think you’re doing it wrong 🫠🤘🏻🤙🏻⚡️

@sirktm 10 ай бұрын

Thanks Dude , Great Video 👍🏼

@SeatTime 10 ай бұрын

🤘🏻🤙🏻⚡️ unfortunately I have to pull the kit out this week and get after another pipe 🤦🏻‍♂️

@Michael-my1vj Жыл бұрын

Heat and shrink the small sharp dents

@SeatTime Жыл бұрын

Talk me through what that might look like.

@anthonyleary7271 4 ай бұрын

@@SeatTime smaller sharp dent you can heat until dull red then use a cloth soaked in ice water this will shrink the metal structure. With dents you'll need to do it several times but it will help with the odd wrinkles as the metal gets stretched when it is dented. a bit of warning it can and will also move the pipe around as it shrinks one spot it can pull a bend so things don't line up. Look up heat straightening of tubing and rolls its often used on industrial machine rolls