Whirlpool Refrigerator Freezer Ice Maker Troubleshooting & Repair (and many other brands)

  Рет қаралды 71,421

Two Keys Studio

Two Keys Studio

Күн бұрын

Пікірлер: 49
@diymaniac876
@diymaniac876 11 ай бұрын
Nice Video, A $20 Part fixed my 13 year old Whirlpool Icemaker, I only had to Purchase the Control Board, $20 and had it Next Day from Amazon. MAN I will tell you, This IS THE COLDEST REFRIGERATOR I HAVE EVER SAW IN MY LIFE !!! At Halfway on Freezer and Fridge, with 75° Room Temp, the Freezer is -2°, and the Fridge is 30° AT HALFWAY, I had to turn them Both down, but yeah man !!! And 1 note to add, The 1st thing you should do is PLUG IT IN, set your Meter to 500 Volts, and test L & N to Verify you have 120 Volts without Power, the rest is Useless, but with the New 1 Installed, water hooked up and Turned on, Plugged IN to 120 Line Voltage, and The Arm Down, I only Did the Jumper Test from T & H FOR 3 SECONDS, and watched the Complete Cylce, Lifted The Arm, Installed the Ice Bucket, Lowered the Arm, Closed the Door and went to Bed, got up this Morning and BINGO, had 3/4 a Drawer of Ice, As you Mentioned I also got the 1.5. Watt Motor as well, and It's fine. 2 other Notes to Add, If you test the Water Valve Circuit, IT WILL POUR WATER EVEYWHERE, as the solenoid operates on a Lower Voltage when not being Jumped, also When Checking For 120 Line Voltage at L & N, IF YOU DON'T HAVE VOLTAGE, the Black wire on the Side, has a VERY NOTICEABLE FUSE in the Clip Holder, so it may be bad, but IMO THAT should be the 1st thing you do, but anyhow, thanks for the Video.
@TwoKeysStudio
@TwoKeysStudio 11 ай бұрын
Thanks for the feedback, I'm glad that the video helped you out.
@diymaniac876
@diymaniac876 11 ай бұрын
@@TwoKeysStudio You're Welcome, and again thank You for the Video, I would've be clueless without it.
@7MBoosted
@7MBoosted 5 ай бұрын
Do you have a part number for the cable. I just replaced my unit, not knowing there was a fuse in the wire, my new unit did not come with a new cable harness.
@diymaniac876
@diymaniac876 5 ай бұрын
@@7MBoosted I'm sorry, I do not, I never Had to Remove the Wiring Harness, just test for 120volts at the deignated pin, if no power then replace the inline fuse, and you should be able to get something Universal etc
@7MBoosted
@7MBoosted 5 ай бұрын
@diymaniac876 thank you for you post, I ended up ordering a replacement harness to see if that fixes it. I don't get power at all to my ice maker.
@richardcallahan8401
@richardcallahan8401 4 ай бұрын
you are the most bestest teacher of ALL I have seen!!! going to see you FIRST!!! thanks very much
@joshleonard7163
@joshleonard7163 9 ай бұрын
Thanks for this! Getting a like from me! I get around 11 - 12 volts reading between L and N. What should I do next to figure out where the power issue is?
@halfanhour2128
@halfanhour2128 5 ай бұрын
I found 2 of the contacts had the green crusties. I used a little vinegar on the contacts then a little sanding to clean them up and now my ice maker is working fine.
@davidv7275
@davidv7275 3 ай бұрын
Had it on one, same thing, cleaned it up and slightly repositioned cause a bit of the metal had fallen off, and it is working fine.
@thoreau7
@thoreau7 Ай бұрын
Question. when i check resistance at v and n i get ol. A short. But when i check the solenoid directly i get 383. Not pumping ice. Any suggestions would be appreciated
@DanielL-ty6pf
@DanielL-ty6pf 7 ай бұрын
To make larger cubes do you turn the white screw counter clockwise?
@panthers8620
@panthers8620 10 ай бұрын
What does it mean that mine has stopped at the 1:00 position? Thank You
@TwoKeysStudio
@TwoKeysStudio 10 ай бұрын
My guess is heater issues, probably due to a bad controller.
@bigbadboogie6842
@bigbadboogie6842 10 ай бұрын
Is it 72ohms also for Europe where we have 230V. My heating element works but says about 290 ohms. My problem seems to be the valve as i have a drippy tube that cloggs maker and eventually fills entire freezer side with ice as it overflows
@TwoKeysStudio
@TwoKeysStudio 10 ай бұрын
The heating element is probably good. Usually, when they go bad, they show infinite resistance.
@Knohgfghh
@Knohgfghh Ай бұрын
I found my fault! Turns out the same fault as yours....The on/off wire rod that the ice pile lifts....it rotates the white plastic shaft....and toggles a contact from one side to another....the button contact that moves between two opposite button contacts for on circuit vs off circuit....slight burn/pitting between the on side buttons so it just would no longer turn on!! Thank you for all the insights!!!
@TwoKeysStudio
@TwoKeysStudio Ай бұрын
Awesome, I am glad to have helped!
@NativeTexan44
@NativeTexan44 11 ай бұрын
It is making ice and dropping, but water is leaking into the ice bucket and freezing. Also some water is leaking out the of the ice bucket and dispenser. I think the water valve is bad. Am I correct?
@TwoKeysStudio
@TwoKeysStudio 11 ай бұрын
That would be my first guess.
@NativeTexan44
@NativeTexan44 11 ай бұрын
Do you have a video on replacing the valve? Where is it located?
@Teknotech881
@Teknotech881 Жыл бұрын
Nice job, Keith and helpers. Great tips on the jumper. Was the piece with the missing electric contacts for the heater?
@TwoKeysStudio
@TwoKeysStudio Жыл бұрын
Thank you Tom. I believe that is what the missing piece went to. I probably should have looked closer at the circuit to verify. I never did find the piece that came off. I always hated when a part went missing and I couldn't find it. Even on copiers.
@paulpoco22
@paulpoco22 Жыл бұрын
Mine seems to freeze over in the internal mechanism and the wheel doesn't turn, like it frozen. Like moisture got inside and frozen it up because a hair dryer blowing and it starts turning.
@TwoKeysStudio
@TwoKeysStudio Жыл бұрын
That sounds much like what mine was doing. The timer should turn on a heater on the tray to separate the ice to allow for it to come out. If the heater never activates, then the ice stays frozen in the tray locking up the timer.
@williamfickett177
@williamfickett177 10 ай бұрын
Could you tell me what it means when I initiated the cam and it started, I pulled the jumper out after ten seconds the cam stopped around the 8 o'clock position. I reinserted the Jupiter but will not move. I can hear a slight noise coming from the cam area but it has not moved since I initiated it. I have check most test points and seems to be ok but its a little confusing at this point as it will not move from this 8 o'clock position Thanks. Oh and no water. V & L 200 ohms.
@TwoKeysStudio
@TwoKeysStudio 10 ай бұрын
Sounds like a water valve problem ir water is frozen in the line.
@williamfickett177
@williamfickett177 10 ай бұрын
Thanks much I did check the V and L points had voltage, is that suppose to initiate water flow or checking the pumps ohmic value. I also noticed that there is ice in the tray shallow and thought that this was holding it back. I check the ohms on the heater coil seemed ok. I will stay with the water valve again wondering what I am check on V & L again thanks for taking your time out. Ice maker motor is new. Thanks again.@@TwoKeysStudio
@bobvic394
@bobvic394 4 ай бұрын
Great video…but you said the ice maker had ice in it when you started! At what stage did the ice drop? Water came in “after” you installed the new module! Thanks
@TwoKeysStudio
@TwoKeysStudio 4 ай бұрын
It would add water but not turn on the heater to allow the ice to exit. Since it was frozen in there with no heat to separate, it wouldn't turn or dump ice. Once repaired, it took about 30 minutes to an hour to drop ice...I think. I checked it the next morning and there was a significant amount of ice in the bin.
@mikebergen7695
@mikebergen7695 8 ай бұрын
What does it mean it it just keeps cycling after I used a jumper to get it started. It does not fill with water.
@difabulous1
@difabulous1 8 ай бұрын
Great video - did the smaller 3 vs, what you had, make a difference with the new part?
@TwoKeysStudio
@TwoKeysStudio 8 ай бұрын
None. It actually seems to make ice faster now than it used to.
@tamlee2004
@tamlee2004 9 ай бұрын
Hello Sir , need your help. what happen with my ice maker power supply at L and N only has 100V. i try new ice maker but it not work. how to do next step
@TwoKeysStudio
@TwoKeysStudio 9 ай бұрын
Check the power at your outlet. You may have a wiring issue in your home if it's only 100v.
@bamapoppy
@bamapoppy 9 ай бұрын
Just watched your video. I’m trying to diagnose why my ice maker pours water but makes ice slowly and doesn’t dump ice into the ice bucket. If I use a jumper wire it will cycle, dump the ice then fill back up. Repeat by jumping manually. Have a good day and thanks for the video.
@randyr2007
@randyr2007 5 ай бұрын
Mine DOES NOT DUMP ICE EITHER. AN IDEA?
@suecope8963
@suecope8963 4 ай бұрын
Why does my refrigerator not make ice
@rockyesterline7942
@rockyesterline7942 8 ай бұрын
How do you turn the ice Maker off? Because my refrigerator never shuts off anymore. And I think ice maker has something to do with it
@estuder32anthonywayne98
@estuder32anthonywayne98 5 ай бұрын
My arm does not drop back down after it dumbs ice! Any ideas?
@redfields5070
@redfields5070 5 ай бұрын
Get some smarter ice.
@TwoKeysStudio
@TwoKeysStudio 5 ай бұрын
probably some kind of binding going on.
@luv14lyf
@luv14lyf 10 ай бұрын
What if it's not getting water to it?
@lenniscata
@lenniscata 10 ай бұрын
it might be the intake valve.
@TwoKeysStudio
@TwoKeysStudio 10 ай бұрын
Like Liniscata said, intake valve. Also it could be a frozen line. Do the output check for the valve and listen for a click. If there is no click, replace the valve. If it clicks but no water, the hose might be frozen.
@luv14lyf
@luv14lyf 10 ай бұрын
​​@@TwoKeysStudiodid all suggested tests, nothing moved, clicked, etc. Installed replacement and still nothing
@mrdenisn
@mrdenisn 10 ай бұрын
Cycle runs but does not refill with water. My valve is fine - the ice maker is not sending the signal to it. It works perfectly when I jumper V and L, but will not fire on its own. It was intermittent for awhile but now has stopped completely. Everything else is fine. Some internal connection is faulty in the cycle. Any ideas?
@kennethshropshire7516
@kennethshropshire7516 Жыл бұрын
Why don't you show what to set your meter at before you do your test. You should ...
@TwoKeysStudio
@TwoKeysStudio Жыл бұрын
Oops...I inadvertently edited that out of the video. It was set to 200ohms for the resistance tests. Basically go to the next higher setting for what the expected ohms or volts are that you are measuring. I have been considering adding a video on the basics of using a meter in the future, so look for that to be added. Thanks for bringing this to my attention.
Ice Maker Repair
7:48
applianceassistant
Рет қаралды 3,7 МЛН
FRIDGE ICEMAKER HOW IT WORKS - TOTAL DIAGNOSTIC GUIDE
21:21
Greg Thomas
Рет қаралды 205 М.
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН
1% vs 100% #beatbox #tiktok
01:10
BeatboxJCOP
Рет қаралды 67 МЛН
Finally! I Found the Perfect Budget Knife!
20:59
Project Farm
Рет қаралды 488 М.
Lighting up the gloom 2
24:27
The Sophisticated Redneck
Рет қаралды 107
Whirlpool Refrigerator Repair - Not Making Ice - Diagnostic & Troubleshooting
12:02
Magic Chef,  Microwave
31:05
Dennis Brown
Рет қаралды 97
Ice Maker Not Making Ice / Whirlpool / What To Check and How To Fix
5:27
The Handyman Journey
Рет қаралды 1,1 МЛН
What's the BEST Fridge to Buy? The Truth Will SURPRISE You!
22:59
Bens Appliances and Junk
Рет қаралды 5 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН