UBNT Power Beam 5AC 500 Point to Point configuration for long range

[@samyu9791]

I have 1.8km link with good signal(all are blue), alignment. What is the maximum throughput I can get? Thanks

[@sastechs7202]

Hello I have a question, Install point to point near power station area have any for connectivity ?

[@bharathmunigala8014]

Can i use ap side power beem 5ac and client side nano beem m5 400

[@TechTricksZone]

yes you cann use only if its connected and no compatibility issue. as both same UBNT so it should work

[@jmrezabek]

This was a Great Video - You made it look as simple as it should be...but for some unknown reason I can NEVER get to the Wireless Mode Drop Down Menu...to see AP PtP and Station??? It is diving me nuts... I have reset the units several times, used different machines, etc...any thoughts?

[@TechTricksZone]

did you try upgrade latest version and check again -techtrickszone.com/2019/01/14/ubnt-airgrid-m-series-firmware-upgrade/

[@arafath788]

How many mbps can possible to transfer ... I have 500mbps fiber connection I want to tranfer by point to point in my work place it’s possible how many mbps will get my destination place ..?

[@TechTricksZone]

it depends on the distance of Link. short distance will give more speed then long-distance and also depend on the area interference and other parameters.

[@arafath788]

Distance only 500 meters

[@jerryjerry3045]

The step by step is very helpful, but the speed you clicked through made it difficult to follow and understand , especially when the warnings came up. but overall very helpful

[@TechTricksZone]

Welocme

[@vishnusharks]

Please suggest model the for 25km range P2P in ubiquiti device

[@arunwaghe1830]

Hi, I have paired both Power beam 5ac device as per your video instruction but from access point throughput Rx showing only to 5 Mbps also signal -66 , please advice what to do increase speed

[@TechTricksZone]

change channel width 20 to 40/80 or change channel also

[@oscarmulusa6389]

I'm trying to do a 5km distance PtP connection but the radios(Powerbeam 5ac 500) won't associate. It gets connected when I use PtMP on both devices and when it connects I get a throughput of 12Mbps only. Kindly advice

[@TechTricksZone]

change the channel and channel width to 40Mhz and check if it work with ptp

[@vishnusharks]

What is the distance you have been configured

[@JayGraphix]

Same mistake everyone else makes ... Everyone cranks up the TX Power, which burns up your antenna ... I am 2 miles apart, running -2 output ... as recommended by Ubiquiti.

[@BLUEfit-i6i]

can i change AP mode ptmp to ptp from client sir?

[@TechTricksZone]

if you want to connected more than 1 Client to same deevice you can use PTMP

[@samchelinaz]

Why did you disable eirp if i may ask?

[@sumansargam3262]

50+Km which device use sir please help

[@DadapeerDA]

Nice JOb., everyone can understand better., Thank you.

[@jaysontesoro4232]

Question sir, this power beam can connect 5km los?

[@TechTricksZone]

Yes if line of sight clear

[@jonjohnson2844]

turned off because of click noises, sorry

[@tiktokvideos4750]

ap me connect dusre user ko singlan kaise dekhe please help me sir

[@alexv305]

Hello, I have a 15km link that is pure line of sight. What kind of bandwidth do you think the powerbeam 5ac gen2 can do?

[@TechTricksZone]

Throughput depend on the area interfernce .so if no-interfrence area and light of sight clear than it should go 100+ Mbps speeds

[@meetbhatia4570]

In 12 km mine only giving 30-35 mbps only beacuse it is very noisy area any way for more throughput ? Someone told me to purchase ligowave costing 100000 for a pair is it worth to buy ligowave ?

[@lucaslebay4500]

Is that good for a 120 meter distance with around 240 users using this ?

[@TechTricksZone]

its depend on the speed you want to give each user

[@vishnusharks]

I have internet one side another side I don't have internet can I share

[@TechTricksZone]

Yes you can - read more about mode-techtrickszone.com/2019/03/14/what-is-the-use-of-different-wireless-mode-in-wifi-router/

[@realinkspecial2294]

Thank you so much...

[@TechTricksZone]

Welcome

[@hokagemoto]

sir the signal strength of my power beam hits to -69 main and -64 receiver..it has warning.. what is the problem of my configuration..???.the distance of my beam is 11km.. thank u sir

[@TechTricksZone]

check the tx power of both radio full 100% and try changing frqency and make signal atleast -60 for both side .your warrning will go once link connectivity will stronge

[@hokagemoto]

@@TechTricksZone thank you so much sir

[@TechTricksZone]

Welcome ! you can get more tutorials at techtrickszone.com

[@muhammadfarhad2570]

How many price??

[@TechTricksZone]

get here- amzn.to/31axi6S

[@vishnusharks]

Can I connect 25 km P2P range

[@TechTricksZone]

Powerbeam for 25KM is higher model visit UBNT site

[@grzegorzsakan3750]

I have ac loco, 150 meters, perfect visibility, speed is 300 mbps. How come yours is 650? Device is rated up to 450.

[@cephas2009]

He uses the PowerBeam 5ac 500, and is using a 80Mhz Channel width! his test is accurate. Increase your channel width! The device rating is on both are 450 Mbps+

[@parkashacharya9931]

sir merey pass 2 roket m5 AC device hai par compiletest nahi aata country site mein or 25 k.m hai distance kya karoo counfigration good nahi hoo rahi hai help me

[@TechTricksZone]

contact in UBNT forum for compaince test enable command.. for 25 KM distance use 30dBi soldi dish antenna

[@mohammadtahashaikh5302]

I have tried the same but it was not working what should i do ??

[@TechTricksZone]

make factory reset both the device and reconfigure one by one as followed this tutorial or also find link in description one more configuration manual for same

[@georgemavimbela]

I wish this was supporting 4G Network

[@TechTricksZone]

May be in future comes

[@V2Kaskader]

Watch Mikrotik LGH lte kit

[@owaisazam5333]

good job sir

[@SkJahangirKabir]

328.08 yd ONLY....! THIS IS NOT LONG RANGE. IF YOU CAN MAKE A VIDEO WITH 20KM LONG RANGE....

[@castlehill6717]

Im thinking of buying one of these.... Do I need two? Im trying share my friends internet from his basic router. Do I need my own access point? A router of my own? Im having trouble understanding this :/. My guess is that it uses a coax cable, how do I convert that back into a wifi signal again so my devices can connect to it?

[@TechTricksZone]

What is the distance from your friend ome to your home? by air distance

[@Sundetov19]

👍👍👍

[@henrypenafiel7970]

buen dia deseo realizar una conexion que pase por 4 puntos, pienso colocar estos equipos: 4 Estaciones base ubiquiti powerbeam Ac 5ghz con antena 27 Dbi 4 2 Ubiquiti airmax pbe-m5-400 antena 25 dbi poe+25km 1 Rollo de cable utp categoría 6 - 305 metros para exteriores quiero saber si esta bien o sera mejor con otros equipos, y que tipo de conexión haría, gracias

[@TechTricksZone]

Please draw a diagram and send to use so we can understand clearly.. send diagram here- TechTrickszone.com in chat window

[@lebergerdesphotons4565]

where's the trick?

[@TechTricksZone]

For what?

[@lebergerdesphotons4565]

I was expecting a trick, given your name. It was just the absolute basics of utilization. That's ok, just don't get why you call it a trick.

[@TechTricksZone]

Find here more - techtrickszone.com

[@tunintunin3417]

That is not long range, 300 m, mine are already working at 5 km, I thought I would learn something here, nothing. Thx for lost time.

[@shivabhalerao6263]

Hi