UHMW Build Considerations

[@tonyflamescontents3763]

I can perceive it right here Your a good cook dough

[@mattrossetti9264]

Awesome video. Thank you for being so informative! Enjoyed learning.

[@agelualofa]

Thanks bro. Love and appreciate your work. Very helpful

[@adog-jw3vg]

Very informative. Thank you

[@granthall2325]

Pls don't forget to do the reel guide or how it works + setting it up & measurements to fit to gun thx from South Africa

[@cobia40]

Go Hebrew National Hotdogs Hahaha. Great video Ed. I met you last year in November when I brought a group down to dive in Key Largo. I swing by and come see you again in June. We bring groups of divers to dive down in Key Largo 3 - 4 times a year from Mississippi. Hope to see you then.

[@terrydottin6495]

Great videos as usual. Can you make a video on cutting the close track and cutting for the spear shaft

[@eugrilo]

Adoro a T-shirt! Love that T-shirt!

[@cameronrodriguez9491]

Will the blanks sold on neptonics handle 3 16mm bands with a 5/16 shaft? Thanks

[@jeffreysarita7723]

Nice sir...I hope i have speargun like that.

[@jelsontvmix5432]

Nice spear gun I wish I have this spear gun

[@adog-jw3vg]

Hey. Looking to build my first gun and having trouble find the teak blank from Neptonics. If I end up buying a piece of teak and cutting my own, what is a standard width of a gun blank?

[@killshotspearguns2522]

hey Adog4368...Depends on what you want to build. Most of the guns I build are 42-44mm x 32-34mm. My bluewater blanks are 2.25" x 1.75" You can certainly cut it down thinner but at some point you will have the wood will begin to flex and Flex is BAD.

[@terrydottin6495]

What type of bits is used to cut the track

[@fambamextreme]

Awesome video...Cut open, closed track, trigger pocket video next😂🤙🏽🤙🏽

[@ericfitz05snakes]

Could you do a video on the open track? It seems like the enclosed tracks are a larger piece of wood than the open track unless my eyes are deceiving me?

[@killshotspearguns2522]

The blanks are actually the same dimension, 42x36mm. The enclosed track is on the 36mm side and the open track is on the 42mm side. People occasionally think the enclosed track is too tall but it tracks well and does NOT flex. The track is deeper on the enclosed track which; 1. puts the shaft lower on the gun. 2. allows me to put the band slot in the middle of the gun instead of the bottom 1/4 3. removes more wood; wood is what makes the gun rigid (eliminates flex) I will do a open track video soon.

[@jeremyh8965]

awesome build! How did you cut the notch for the line routing?

[@killshotspearguns2522]

I use a rotary tool with a wood cutting bit and a small round file. It removes material quickly so you really have to be careful when cutting that groove.

[@gerardcapuafishingtv8174]

Amazing video plss do a spearfishing video I like it!! I wish I have that one🤙🥰

[@granthall2325]

U need to make a T-shirt that says THE FISH JUST SURRENDER!!!! 🤣🤣🤣😂😂😂I laughed my head off when you said that!!!

[@benjamincyr1697]

Where do you get all of your parts from ? Love the vid !❤️

[@WRA005]

Neptonics I think

[@killshotspearguns2522]

Hey Ben Cyr, I use both Neptonics and Koah parts. Which I use depends on availability and the style of the speargun. You can purchase parts directly from them or contact me. I usually have a pretty generous supply of parts on-hand but will let you know if something is out of stock.

[@benjamincyr1697]

@@killshotspearguns2522 Thank you very much ! I love the content and the details :) thxx - will contact you !

[@tripurafamily9583]

Where can I buy the triggers? Would anyone tell me plz?

[@killshotspearguns2522]

I don't list them online but you can purchase them by contacting my shop. Phone number and email address is on our website (www.killshotspearguns.com).

[@vinniesquad1451]

Where can I buy the kit from?

[@christopherbugros9370]

Hw can I bring that wood shok in Trinidad 🇹🇹

[@tombaguam]

Where do you purchase your teak speargun blanks?

[@killshotspearguns2522]

Did you ever find a source for Teak? I had a major supply issue for awhile but I think I've gotten a handle on it and might be able to get something sent out depending on how much and what you are looking for.

[@rickydelacruz1998]

How to order sir and how much

[@lmnop20sharks]

Hi, can I use 2 x 16mm bands on a 7mm shaft?it's a 130cm spear gun I'm making with a 160cm 7mm shaft.

[@killshotspearguns2522]

Yep, I personally use 14mm bands but I rig most of our longer guns (110+) with 16mm bands. I would only use two bands though as three will simply overpower the shaft and you will lose accuracy.

[@lmnop20sharks]

@@killshotspearguns2522 OK, my measurement was wrong. I thought the length of the gun was the entire stock. It's a 110 I made. How do I get the correct length of the bands?

[@DeepBlueSpirit2]

Hi brother, there are some variables so there is no exact rule. It depends. Do not overpower a 7mm shaft. It will oscillate when fired and it will kill shooting range. 'Less' can be better lots of time. Also the stretching and size of bands will depend also on the ability (or comfort) to be able to load a gun. You might even go for a thicker but shorter shaft. Less bend, less oscillation, similar weight - maybe even better range. For your 160cm @7mm shaft you can easily use smaller size bands. For 14mm (small ID) bands you might like a 65cm rubber. Nice to load and good acceleration. Test the gun on accuracy after - so it is known how it shoots. Save dives!

[@lmnop20sharks]

@@DeepBlueSpirit2 I will try the 14 mm bands. I find the 16mm and have my chest sore and I am wearing a 3mm wet suit.

[@JoandryGr]

Hi friend how much do you sell 1 gun, how much also one blank? And where do you buy the mechanical for the the gun ,like the trigger and all. Thank you and nice video

[@tg2515]

Neptinics sells all the parts you need

[@natsudragneel7430]

That was good

[@scubadiving123]

Hii 1 speargun Tigger can be ordered

[@mox1968]

Great video, answered a lot of questions I had that I didn,t know I had !!!!! Do you coat your guns with teak oil or are they sealed with something else?

[@killshotspearguns2522]

I use Watco teak oil finish and then use a hand-rubbed polyurethane finish. It doesn't flake but it does require 3-4 coats before it goes on the rack. Then I just wipe it down with oil from time-to-time to keep it looking good.

[@benjamincyr1697]

What type of wood do you use for your prototypes? Love the vid !❤️

[@killshotspearguns2522]

Depends...For a concept on a total prototype I'll use a 2x4 or other cheap lumber. If I want a working prototype I'll usually use African Mahagony. It is cheap, will stand up to saltwater pretty well and is similar in density to teak so I get a feel for how it will need to be weighted. I can also use it for a few years if I want to. Once I get everything dialed in (trigger spacing, track, line routing handle bases, etc.) I'll keep it in the shop so I can measure against it when building the teak guns.

[@benjamincyr1697]

@@killshotspearguns2522thank you very much !! :)

[@JohnreySimbajon-ey5iq]

How much? How to buy?

[@fishhunter348]

Do you just epoxy the track in?

[@killshotspearguns2522]

Sorry, didn't see your comment until this morning. No, I use two screws to secure the track in-place. You could glue it in w epoxy and I'll sure it would be fine...probably more stable.

[@NO-kq7jy]

We need some videos of you spearfishing

[@killshotspearguns2522]

I need to get out more...but when I go I usually focus on just shooting fish and leave the camera in the bag!

[@normanjr.jajalla7002]

Sir I'm Norman from philippines.i want to buy a speargun.killshot speragun like what I seen in your video.and sir how much it cost for that?.

[@killshotspearguns2522]

Sorry Norman, I actually don't make those anymore. I still build epoxy enclosed tracks which are really nice though.

[@fabrigasmaka8256]

How much would I sell a 140 cm for, do u ship to to Canada or Caribbean?

[@killshotspearguns2522]

I don't build that in a 140cm, sorry. And yes, I would and do ship to the Caribbean and Canada. I usually use PayPal for those transactions.

[@fabrigasmaka8256]

@@killshotspearguns2522 ok I understand. What's the price range for a 135, triple rubber. Do you think, it could reach before Christmas?

[@gawangconstructiontv195]

Nice boss

[@reedzwarrior3648]

Nice vedio sir

[@wailyncutamora7256]

Wow

[@ArifudinMyf]

Jika saya ingin membeli spearguns ini saya membelinya lewat situs apa ..?? Saya orang indonesia 😇

[@jksperao132]

pak berapa harganya karet speargun saya dari negara Indonesia bisa saya pesan karet pak

[@P4NC4_hakim546]

Hello Im from indonesia 🇮🇩🇮🇩

[@DeepBlueSpirit2]

Nice, fun and clean presentation brother. Great informative video. All the best! >

[@nasuririzal4324]

Hey mister, make just one speargun for me

[@joselitolace8779]

..sir when i was saw your video i mean i like your vlog about speargun but im a beginner...about fishing boss i have no enough money to buy speargun can you pls give me 1 speargun even second hand its ok for me thank you...