ULTIMATE POWER!!! TRAXXAS SLEDGE 4985 1650kv MAX6 COMBO

[@richduperbash2966]

In case anyone was curious, temps with the set-up were great 😍. I did get a 170F on the motor at one point, but I was hammering it in extreme heat and fine, slippery dust. Overall temps were 150F motor and around 125-130 tops ESC. Unfortunately, the rock jambs likely contributed to a damaged rear ring gear. I heard slipping and swapped in a machined input and ring between locations. Mesh is still 100% solid thanks to the M2C mount 😍. LOVE this Max6 combo!!!! Same setup as my Fireteam 6s. 🍻

[@haroldrivera3640]

@Richduperbash I need ur help,since I install max5,1100kv on my xmax my rear ring gear keep stripping even shining the input gear,any help will be much appreciated, God bless u and yours

[@richduperbash2966]

@@haroldrivera3640 my best guess is there's a crack somewhere in the diff case or bulkhead allowing the gears to push apart or get out of alignment. I'd also check your bearings in case one is starting to seize. Cracks can be difficult to see. You might have to flex the plastic in your hands to expose a fracture line. If this is a repeating theme I can guarantee it's either a bad bearing or a busted bit of plastic. 😎💪👊👊

[@damoh4895]

hey rich, if you fall into issues with the diff crown and pinion gears, i believe the bulkheads flex under load, afterall theyre very thin plastic. especially around the bearings. i went with some vitavon bulkheads and diff gears, havent stripped a gear since.

[@richduperbash2966]

@@damoh4895 thanks so much for the input Brother 👊. This is exactly what we spoke about on the M2C test team. I'll be running Vitavon in the rear sometime soon 🍻

[@damoh4895]

@@richduperbash2966 cant fault the vitavon bulkheads or the gears they sell, all top quality stuff. i already have a max6 in mine, looking at fitting the 1650kv myself in the next couple of months. im still running the factory chassis tho, havent bent it yet. have you seen the vitavon axles and carriers yet? damn are they beautiful.

[@Basherqueen]

M2C definitely comes up with the most brilliant design when it comes to after market parts. Very inspiring and challenging for me and others 👍👍

[@richduperbash2966]

Thanks so much Kimberly 😍. So grateful for M2C and your wonderful line of Basherqueen custom upgrades 🥰🥰😎💪👊👊

[@CommanderAstigRC]

Awesome session with David Bro Rich. The Sledge is quick and agile with the extra power Bro. It's always Nice to have extra power when you need it. What an absolute Beast of a truck the Sledge has become. Huge props to M2C Mitch and Avery turned this into such a kickass Tank Basher! Another awesome upload brother. Love n enjoyed it!

[@richduperbash2966]

Thanks so much Brother Chris 😜. Loving this reverse, big power setup 😍. Huge thanks to Mitch and Avery for transforming the Sledge into a hardcore basher 🚀🚀. Stoked Dave could get out there too. 🍻🤙🤙😎💪👊👊

[@averylooper5534]

What an awesome bash! I'm just loving those huge table upside down table tops!! You really put the beat down on it! Thanks for posting

[@richduperbash2966]

Thanks so much Brother Avery 😜!!! You've hit a home run with this reverse motor option 😱. She's a different breed of animal with this high torque setup 🍻🚀🚀😎💪👊👊

[@MRMechanicRC]

Dude that thing is just ridiculous now!

[@chadbiermann3380]

Great video Rich!! You have that Sledge tanked out and dialed in!! Insane air and amazing control!! Always a pleasure to watch!! 💯💯😀

[@richduperbash2966]

Thanks Chad 🤗. The Sledge is achieving her potential thanks to the upgrades and big power setup!!! 😱😎💪👊👊

[@AldoLoyal]

Loved it brother sorry about your ramp failure😢 but it’s been good to y’all over the years I agree 100% you cannot bash the sledge as hard as you just did without M2c chassis and Motor mount💪 Rock on brother🚀🤩💪

[@richduperbash2966]

Thanks so much Brother Aldo 🤗. Yeah it's a bummer about the ramp finally giving way to years of abuse 😝. Wish these ones were still available. No question the stock chassis and mount would've noodled up from this session. I still can't believe Traxxas fubarred the stock design 😂. Talk about crap engineering. Huge props to M2C for making the Sledge right with proper design and materials 😍👍👍😎💪👊👊

[@BarstoneRC]

Man Rich that was a killer run that car was just fly and beautiful that new reverse motor mount set up looks like it’s working great, I’m still running mine in the forward position I’ve been enjoying it at some point I might flip it. But great bash brother

[@richduperbash2966]

Thanks so much Brother David 😜. She feels Killer with the added torque and very balanced with this reverse setup 😍. The standard set-up worked fine, but the Sledge is heavy enough to benefit from a stronger system and really get the power down. I love the Max6 combo!!! 🚀🚀😎💪👊👊

[@rcsendandblast1579]

I can’t stop smiling for real 😊🤘 what fun the hobby has to be had. Great session Rich what a ripper that thing is 😁Wow

[@richduperbash2966]

Thanks so much Brother 😜!!! This was one of those days when the will to bash beat the crazy hot weather 😱🤣🤣😎💪👊👊

[@rcsendandblast1579]

@@richduperbash2966 yes indeed I hear you. I was lucky today I spent the majority of my last 2 days allowed to work on my hobby corner. That was great I got my Outcast almost ready to go. Last thing before the old girl is reborn is ohh 2 things mabey 3 Custom Rc upgrade rear skid and lipo straps. And acerman and servo horn. Other then that I am ready to go new lipo’s new wire connectors all cleaned up with new delta fan configuration My buddy helped me with sending me some 3D printed fan adapters for the esc and motor. How awesome is that. Not sure if you have seen his channel or not if you haven’t seen it go sub and check it out. NBRC channel is awesome. He helps me a lot with learning things with the hobby. Along side with BasherBodies I get a lot of help I am so so happy ❤️🤘😎 RC sure brings us together that’s for sure there will one day be a RC Holiday I can see that happening. It’s sure gaining traction that’s for sure. You are one of the greats buddy own it’s like the Boss you are 🤩👑🥇🍻

[@tonysmith7989]

Another 💯%🔥 run Rich 9:35 of the vid are my favorite jumps. The long upside down stalls. Thanks again for sharing your fun. 🤜🤛

[@richduperbash2966]

Thanks so much Tony 🤗. The Sledge was getting some good hang time with the new setup 🚀🚀. Glad I could patch up the ramp with some Gorilla tape 😂😎💪👊👊

[@radar6823]

How is that driving even possible? Incredible Rich. Thanks as always. You definitely set the bar. Unbelievable “AIR” control!👍👊^^^^^^INSANE air as always! 🤙

[@richduperbash2966]

Thanks so much Chris 🤗. This Max6 combo is super smooth for the amount of torque it has 👀. Makes corrections and throttle delivery a bit more predictable. 😎💪👊👊

[@NBRC]

awesome run .... my chassis is in the mail, normal motormount already in tha house .. can't wait for it so i can rip it ... great truck

[@richduperbash2966]

Thanks Brother 🤗. This is a different truck with the 7075 T6 chassis and motor mount 😍

[@NBRC]

@@richduperbash2966 i soon will find out ;)

[@madmatt2769]

Wow bro, that Sledge is even more awesome than before! 💪🏻🤜🏻👊🏻🤩🤩 Killer driving as always 💯👊🏻👊🏻👊🏻👊🏻

[@richduperbash2966]

Thanks so much Brother 😜. Digging this Big power setup 🍻😎💪👊👊

[@AverageRCBasher]

Those blind landings are so ballsy, geez

[@trinidadtobago81]

Awesome bash session as always love the sledge. Got my M2C upgrades the motor mount is amazing with a perfect mesh soon I'll do the chassis got mine in a few days ago thanks for all the ideas and thank you M2C

[@richduperbash2966]

Thanks so much Brother 🤗. Awesome to hear your feedback about the mount 👍. Mitch's chassis design to accept both motor directions was brilliant 😍

[@TurtleRc]

Your throttle control is legendary sir.

[@richduperbash2966]

Thank you Brother 🤗. Really appreciate it. 😎💪👊👊

[@TpPartsRcXtreme]

Plain simple AWSOME Session Rich, made ma friday 🥰. The Sledge looks solid as few, and i agree for hard and i mean real hard bashing the m2c is a must like it is for all other brands 🤗.

[@richduperbash2966]

Thanks so much dear Brother Thomas 😍. M2C has really done it right with the Sledge. So nice to have a big power setup in this heavy girl. She's moving great 🚀🚀😎💪👊👊

[@nunu4692]

3 seconds in and my mind was instantly blown away😭😮

[@GreatLakesRC]

Awesome reverse motor rip Rich! That set up is mega power 💪💪 Loved it

[@richduperbash2966]

Thanks so much Brother Aaron 😜!!!! Fitment was perfect thanks to Mitch and Avery 👌. Loving this setup. Truck hauls complete ass and has Killer torque 🚀🚀 😎💪👊👊

[@chaoticadventure]

Another duperbash super bash! Nice driving bro,sledge got some hang time! Damn thing rips! I'm still fine tuning my fireteam.

[@richduperbash2966]

Thank you very much Brother 🤗. The 4985 feels AWESOME in her. Can't wait to get my Fireteam back out soon. Same power setup, but way more fun to bash 😍

[@jacobhenson3952]

Really nice run bro. I got all my M2C stuff on my truck and absolutely love it. I ended up taking my max 6 out and trying the new max 8 g2 in mine with the 2250kv motor and I love it. The new max 8 has been amazing for me so far. It stays really cool and feels just like the max 6 power.

[@richduperbash2966]

Thanks Jacob 🤗. Really appreciate the feedback about the G2 Max8. I'll have to check it out 🍻😎💪👊👊

[@droningharry]

As much as I hate to admit it, Traxxas has built the best Truggie platform. The mods just make it untouchable, it’s a true Beast.

[@richduperbash2966]

Well....the Sledge is a Beast thanks to M2C 💪. Between the chassis and legitimate 7075 sliding motor mount she's a force to be reckoned with. 🍻😎💪👊👊

[@alexarel2010]

I love mine

[@ayocxrry-2435]

Facts I loved my stock sledge but I just installed the m2c jackhammer kit on mines waiting for my hobby wing max6 combo 🫡

[@capracoins4317]

Fairly new to the channel but your driving skills are insane

[@richduperbash2966]

Thanks so much Brother 🤗

[@rcsmith5909]

Just grabbed a sledge . Getting the Badger Queen and M2C upgrades same as you. Then l feel it will be a very tough truck!💪🏻🍺. Awesome vid my brother!!🍺🍺👍🏼 . Just ordered the v2 outcast as well 🤩🍾

[@richduperbash2966]

Congrats Brother 😱!!! The Sledge is a different animal with the upgrades. You're gonna love the V2 Outcast too. 🍻😎💪👊👊

[@robgoffroad]

106? You must be in Arizona! I was down there for five years and finally had enough of the heat (and snowbirds in the winter).

[@kansascityrc]

That looks like a beast with that combo!🔥🔥🔥 quick question, where would one find small plastic ramps like those at 5:17?

[@richduperbash2966]

Most definitely a Killer combo for this reverse motor setup 😱. Unfortunately the ramps were discontinued over 2 years ago. Bought them from Discountramps.com. 😎💪👊👊

[@darksunridah]

I have this set up in my Typhon 6s and Kraton 6s. I just got another Max 6/1650 combo for my Mojave 6s. I love it. I think I wanna go with a 22T pinion. I don't do much jumps just drags. Love the video

[@richduperbash2966]

Thanks so much Brother 🤗. Yeah I love the 4985 in my Fireteam and this sucker 🚀🚀. My buddy John sold me on the Max6 combo in his K6s. 😎💪👊👊

[@EJ-74]

106 🥵 dang I feel for ya It was 93 here in NC that's hot enough for me 🤣 The Sledge is insane bro Holy cow that thing rips 🔥 Awesome vid ✌️

[@richduperbash2966]

Thanks so much Erric 🤗. Yeah anything above 90F is hot 👀. Doing my best to stay hydrated and bail out quickly on these nasty days. The Sledge is hauling ass with this new setup 😍

[@RC4us]

Again killing it... truly a inspiration

[@mybusiness6125]

Awesome video as always but cracks me up when you say "Sledge is a great platform". Meanwhile, M2C chassis, motor mount etc., Arrma rods, wheels, etc. Basherqueen towers. Hobbywing power system. Uh, what exactly is still Traxxas on this thing? Maybe the arms and chassis brace? LOL. Keep on rocking!!!

[@richduperbash2966]

The Sledge isn't a great platform in stock form in my opinion. Traxxass greatly exaggerated the stock durability and fubarred the motor mount design. Price is overpriced like all their stuff. It's only great once it's made more like a Kraton with M2C and other hop ups. 🍻

[@jptothetree]

4:02 this just seems like the most unnecessary crash of all time 😆 The Sledge is just looking amazing after all the work you've put into it!!

[@richduperbash2966]

Yeah I think he stabbed the brakes or something 👀. Definitely had to chill out a bit with all the people around. Loving this 4985 reverse mount setup 😎💪👊👊

[@marc1981er]

I want do like you but with the Stock chassis, i would just cut off that piece from the chassis, you think it is a good solution, modify the Stock chassis?

[@richduperbash2966]

You could certainly modify the stock chassis to work, but it's no where near as strong as an M2C 7075 T6 chassis.

[@marc1981er]

@@richduperbash2966 you think gpm Option Chassis is as strong as an m2c Chassis? In my country the gpm is easier to get

[@curtishubbard907]

I wish traxxas would upgrade the pin grub screw’s for the revo 2.0 and the sledge for the center drive shafts wonder if m2c can make better ones for them would help great video as always worth the wate have a great day man

[@richduperbash2966]

Thanks so much Curtis 🤗. M2C is just getting started with the upgrades. Really appreciate it Brother. 🍻😎💪👊👊

[@jc49fishniner4lif7]

One word my friend AWESOME 💯👍

[@richduperbash2966]

Thanks Brother 🤗

[@wiling924]

How long does the battery last? And how much miliampers the baterry have?

[@richduperbash2966]

Running an Ovonic 5200 mah 50C and normally get 15-20 minutes of run time depending on terrain and throttle use.

[@blacksheeprc8113]

Killer bash bro

[@richduperbash2966]

Thank you Brother 😎💪👊👊

[@cyclonerc1625]

All Right First 👍To the 👑 of Bashing

[@taxpayertroy]

Brother duperbash, That’s the biggest motor you can run in this mawf? Thank you

[@nicolomasto7628]

hello congratulations a real 🚀 I wanted to ask you which pinion / crown ratio did you mount in this video to have this speed?

[@richduperbash2966]

Thanks Nico 🤗. I'm running 23/46 gearing with the 1650kv 4985 and smaller Backflip LP's.🍻

[@nicolomasto7628]

@@richduperbash2966 thanks for answering me, I wanted to ask you for advice x since I don't jump, I just need more speed for you, which ratio is suitable ? without heating of course

[@richduperbash2966]

@@nicolomasto7628 my temps have been good. You typically gain around 3 mph per tooth gain with the pinion. You'll have to experiment and keep tabs with your temps using an infrared temp gun. Above 160F motor is getting toasty.

[@nickhathaway4617]

Sick as usual I think a hobbystar 4585 1580kv or 1800kv Would be absolutely perfect Slightly smaller and lighter You should definitely try I would love to see it

[@richduperbash2966]

Thanks Nick 🤗. Hobbystar makes great motors. Get the gearing right and it'll be a screamer. 😎💪👊👊

[@tmethemillerexperience5905]

Link for that reverse motor mount and chassis?

[@richduperbash2966]

m2cracing.net/shop/shop.php#!/M2C-1453-REVERSE-MOTOR-MOUNT-UPGRADE-KIT-FOR-S-SERIES-TRUCKS/p/490913268/category=13612792 m2cracing.net/shop/shop.php#!/M2C-1499-S-SERIES-CHASSIS/p/478044753/category=136127921

[@richduperbash2966]

Go to the website to pick the mount kit you prefer. There's more than one.

[@jordanritchie2198]

Nice session Rich that's a bummer on the mini kicker ramp. If u find any send me the link I been looking all over for them. Thanks for the upload see ya in the next one ✌🏻✌🏻

[@richduperbash2966]

Thanks so much Jordan 🤗. I managed to pop the plastic back into place and Gorilla tape the ramp 😂. I'll definitely share the link if I find replacements. Definitely in the market for new ones. 😎💪👊👊

[@jordanritchie2198]

@@richduperbash2966 😂 got love gorilla tape 💪🏻💪🏻. But yes please do I can't seem to find any

[@nickhathaway4617]

I really want you to try a hobbystar 4585 1580kv feels just like the hobby wing but little lighter because of the dimensions in a little torque

[@richduperbash2966]

I might try one Nick 🤗. You know I love my Hobbystar motors 😍. I gotta say the Hobbywing 4985 1650 is a complete animal though 🚀🚀

[@bashemrc6871]

Is this over by the pump park off Richards Blvd?

[@richduperbash2966]

Yes indeed 🤗. Just have to mindful of security guys and not have large groups. 🍻

[@blacksheeprc8113]

That's what I have in one of my kraton xls

[@joshloose1078]

Still the king of bashers bud!

[@richduperbash2966]

Thank you Brother 🤗

[@StevenYDG69]

rich, have you ran the Hobbystar 4076 motors in anything? got the 1700 for my sledge no real idea on gearing

[@richduperbash2966]

Yes, I ran the 4076 1700 in my Tekno awhile back. It eventually overheated and gave out. Might try an 18T and go from there. Just depends on what kind of speed and wheelspin you're after.

[@SteynvanLent]

Holy sh# what a ripper! 😱

[@richduperbash2966]

Yeah this setup is awesome 😱. The Hobbywing 4985 is a Beast 👀. Props to M2C for making the reverse mount system a reality 🍻😎💪👊👊

[@juanarroyo2282]

Hey man I’m looking for help,my Xmaxx after My HS installed 1100kv and 54,29 now is blowing up diff ring gears,are u have or that happens to u or what I should change .thanks for the help in advance

[@richduperbash2966]

I've only been through a couple ring gears and it was because either the diff cover or bulkhead had cracked allowing the gear to shift under power. I replaced the diff cover with a Hot Racing one and also Hot Racing alloy hinge pin plate (below the plastic skid plate) front and rear. That helps strengthen the bulkhead from the bottom. 🍻

[@juanarroyo2282]

@@richduperbash2966 waooo tanks man never tough u gonna answer,I’m a sub for sure but u giving me the help is awesome really thanks I will do it for sure ur advice.keep bashing and God Bless u and yours.is awesome chat whit u #LivinglegendDuperbash

[@richduperbash2966]

@@juanarroyo2282 God bless you too Brother 🤗

[@juanarroyo2282]

@@richduperbash2966 Hey man the problem so far was the bulkhead we’re the screws hold the diff cover was not holding the cover so it was expanding and bommmmmm ring gear gone.so far I send it yesterday at track in my HS,go true a complete set of lipos and thanks God clean Xmaxx.I tried to go Duperbash but hey it’s only one #livinglegendduperbash.thanks brother really appreciate.God bless u all🙏🏽

[@monkfiche9384]

Hey, are you using the existing ESC chassis plate and ESC top plate (on top of the motor mount) m2c items? Or are the items you are using as ESC and receiver plates part of m2c’s beta testing/not released yet please? Cheers!!

[@richduperbash2966]

The motor mount, ESC mount, and center diff plate (where the reciever box was bolted to) are all M2C parts that replace the stock bits. They're soon to be available on the M2C Racing website. The 4mm 7075 T6 chassis is available already. In essence, M2C has transformed what is possible with the Sledge. 🍻😎💪👊👊

[@monkfiche9384]

@@richduperbash2966 great thanks for that! Cheers!

[@teknostructures4629]

4:08 wowwww

[@decayer6710]

Just curious, did you tune the esc by any chance, like punch or something? I got pretty much everything as identical as yours but it can barley do a backflip.

[@richduperbash2966]

Yes, I turned my punch up to max 5. Make sure to calibrate your controller to the ESC under throttle setup to assure you're getting full throttle, brake...etc. On that note, if reverse seems faster than expected, it's possible the motor direction is reversed. I've had that happen before where I had to reverse motor direction and reset the controller direction too. 😎💪👊👊

[@decayer6710]

@@richduperbash2966 Thank you! Great video btw, i subbed.

[@richduperbash2966]

@@decayer6710 thanks Brother 🤗

[@Unknownentity12345]

What pinion/spur are you running here?

[@richduperbash2966]

Think I was running a 46 spur and 22T Robinson Racing #1222 extra hard pinion.

[@RCPropaganda]

Got my chassis in, just need time to swap everything over.

[@richduperbash2966]

Congrats Brother 😱!!! The swap goes pretty easily. It's a pleasure to do and the fitment is perfect 😍

[@marlincoffia6408]

How did you attach the Arrma Kraton links in the front closest to the wheel?

[@richduperbash2966]

I used a rear ARRMA swivel ball in the front plastic link plus a washer to take out some slop. 🍻

[@marlincoffia6408]

@@richduperbash2966 thank you Sir. Also, another absolutely fantastic video bud.

[@richduperbash2966]

@@marlincoffia6408 thanks Brother 🤗. Happy New Year!!! 🍻

[@Hoosierdaddyjones812]

Some plexiglass and glue prob fix that ramp to last bit longer or maybe some stick down flooring

[@richduperbash2966]

Thank you Brother 🤗. Appreciate the suggestions. I had previously used JB Weld Plastic bonder and it held quite well on the underribbing. Hopefully I can find some new ramps before long. 🍻

[@thejeepinrealtor5742]

Same setup I run in my EXB. Doesn’t run cool at all when I really run it hard. It doesn’t go above 170 or so. Can’t make up my mind about whether to get one of these or not

[@richduperbash2966]

None of the electronics run cool when you run really hard. I've found the 4985 to be more efficient than my Hobbystar 4092's though, especially in hot weather. The Sledge drivetrain feels smoother than the EXB (in my opinion). Tough call on getting a Sledge 🤔. Definitely an expensive venture to make solid. It is a pretty tough truck, but an M2C chassis and mount is a must for harder bashing. 😎💪👊👊

[@danimudura3213]

I have a 1650kv hobbywing motor with max8. Why does my esc keep going into protection?

[@richduperbash2966]

You probably need a Max6. Could try gearing down, but the 1650 was really designed to pair with the 160A. 🍻

[@BatmanRc]

Hello this run on 8s lipo ? Thanks

[@holmer1982]

Is there any reason to get this, if you have a kraton exb? I got an exb with same motor set up and it just seems to me, that the 2 trucks are too alike.

[@richduperbash2966]

The Kraton EXB is still my favorite when compared to the Sledge. The Sledge does handle differently, perform impressively, and take a great beatdown with the proper upgrades. The transmission feels slightly smoother in my opinion, but the added cost to buy and upgrade the Sledge over a K6s EXB is significant and it's debatable if there's any or enough reason to make that choice. 🍻😎💪👊👊

[@holmer1982]

@@richduperbash2966 that’s what I thought. Thanks for the answer! Love your videos 👍🏻

[@harriprince6545]

Looks really fast mate what's the top end speed?

[@richduperbash2966]

I haven't measured yet with GPS but probably 60+ mph. 🍻

[@harriprince6545]

@@richduperbash2966 I have v2 widemaxx got a max 6 esc and there 2200kv motor it does rip as well to be fair but this looks like where I'll be heading next I've vitavoned pretty much everything other than bulkheads too so it's a tank but I'm impressed by this thing not much has been impressing me more than what I have but this definitely caught my eye

[@jimeikevag3146]

Did you need a mod to fit the max 6 when you had the motor reversed?

[@richduperbash2966]

In the stock position, I simply replaced the VXL for the Max6 with 30lb mounting tape and a zip tie (made a small cut in the bottom plastic to fit the tie under). For the reverse motor mount set-up, I bolted my Max6 onto this M2C ESC mount up front. m2cracing.net/shop/shop.php#!/M2C-1452-REVERSE-MOTOR-MOUNT-KIT-FOR-S-SERIES-TRUCKS/p/488858460/category=136127921

[@NiteShade_BZ]

Was this on 6s or 8s?

[@richduperbash2966]

6s

[@ntwrc3755]

What pinion and fluids are you running trying to build same truck

[@richduperbash2966]

I'm running a 23T pinion with 50k front, 20mil center, and 20k rear diff. Also running M2C pistons with 80-100 weight shock oils if I remember correctly.

[@ntwrc3755]

@@richduperbash2966 thanks brother

[@jamespayne9935]

Hey what kinda ramp is that

[@timbootz8894]

Hey since you have had this motor combo for a little while now, what is the best gearing combo for this set up? Still the 46t spur and 23t pinion? Let me know thank you. I am currently running the same set up in my sledge.

[@richduperbash2966]

Hey Tim 🤗. I really like the 23/46 setup with Backflip LP's. I'd say 22T if running any larger diameter wheels. So far my temps have been good despite bashing in 100+F weather and bone dry powdery dirt. 🍻😎💪👊👊

[@timbootz8894]

@@richduperbash2966 ok cool thank you, also I just got the 50t vitavon spur.. what pinion would you recommend to use with the 50t? I was thinking maybe a 20t? Let me know thanks man

[@NewLifeRC989]

@@timbootz8894 if you’re looking at a 2:1 ratio between spur and pinion, with a 50t spur, your pinion would be 25, which I think is quite large considering the available and adjustable space on the sliding motor mound. You should be good with a 20-23t pinion when running 50t spur. Monitor temps and cogging as that may affect your gearing choices. I run 22/50 on my Fireteam with Max 6 4985 combo and it runs incredibly smooth. My sledge is 20/46.

[@austinshepherd6675]

You’re running 46/23 right? Any esc settings outside of stock?

[@NewLifeRC989]

@@austinshepherd6675 punch 4, BEC 7.4 and that’s about it in terms of settings that would adjust the drive ability of the truck itself.

[@tyehicks8739]

What Castle motor would you recommend?

[@richduperbash2966]

I'd go with a Castle 1717 1650kv. 🍻

[@MrAbm860]

4s or 6s tires part number for toe links

[@richduperbash2966]

The Backflip LP's are the smaller 4s version. Don't have my manual handy for the part #'s at the moment. They're 6s Kraton steering links. 🍻 www.ebay.com/itm/193098541726?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=193098541726&targetid=1262749490102&device=m&mktype=&googleloc=9032466&poi=&campaignid=15428034462&mkgroupid=133947154481&rlsatarget=pla-1262749490102&abcId=9300763&merchantid=113678668&gclid=Cj0KCQjw2_OWBhDqARIsAAUNTTGYqqWWMOzX0Gyz0qEqHR9FATYEun6JBGjvtNoYzERN4qQBp3bHZW4aAu_kEALw_wcB

[@ayocxrry-2435]

hey wassup rich can you please link me to the battery you have for this setup please

[@richduperbash2966]

I use to run Hobbystar 5000mah 100C packs from RC Juice. The prices have risen so I've switched to Zeee and Ovonic these days. 🍻

[@FarmerFpv]

Beast combo! It's like a dog with the zoomies, lol.

[@richduperbash2966]

Thanks Brother 🤗. She's got some serious grunt now 😱🚀🚀

[@tonysmith7989]

Yup at the end you knew the shot. Lol

[@EJ-74]

Pop rivet a stop sign etc over your ramp it'll be good as new 😉 lol

[@skillz2tthemaxx157]

I’d pay you to work on my RC cars to run this beasty as yours doo

[@CANAMROCKS1]

Man I just love seeing all the Arrma parts on the Ol crapaxxas Sludge! Probably be easier n cheaper to put a sludge body on a 6s Kraton exb n call it done! 🤣😂

[@richduperbash2966]

LMAO 😂. I like your thinking 😎💪👊👊

[@StevenYDG69]

Wow! Not much traxxas left to it now... not a bad thing!! Lolol

[@richduperbash2966]

LMAO 😂. Indeed Steven. Leave to M2C Racing to turn an RTR into a proper tank 😎💪👊👊

[@joshloose1078]

Gorilla tape will fix that ramp just like a body lol

[@richduperbash2966]

You know it Josh 😂🤙🤙

[@ColPKing]

Why does anyone treat expensive toys like that. They turn out to be money Pits instead of enjoyment unless you have an issue and just need to destroy things.

[@richduperbash2966]

The great thing about our hobby is choosing how to use your stuff. What's fun for you, might be boring for me and vice versa. I'm a parts tester and developer for M2C Racing. Been at it since they first started designing parts for bashing years ago. Proper durability testing requires proper stresses are placed on prototype parts prior to mass production. 🍻

[@ddbrink663]

the sledge looks to be a lot like the arrma kraton except more expensive and the body flys off once in a while..not for this kid

[@richduperbash2966]

Actually, the more M2C has made it like a Kraton the better it's performed 😂. Definitely overpriced like all Traxxas rigs. 😎💪👊👊

[@CANAMROCKS1]

Man I just love seeing all the Arrma parts on the Ol crapaxxas Sludge! Probably be easier n cheaper to put a sludge body on a 6s Kraton exb n call it done! 🤣😂

[@richduperbash2966]

LMAO 😂. I like your thinking 🍻😎💪👊👊

[@CodyRadcliff-p3g]

What batteries do you run?

[@richduperbash2966]

I was running Hobbystar 5000mah 75C single 6s hard packs. Now I'm using mostly Zeee and Ovonic packs mostly due to cost difference off Amazon prime.