Underfloor Heating Installation with ProWarm In-Screed Wet System

[@HweeBinLi]

Well presented. Three questions 1) Total cost for the underfloor 2) Why underfloor in the garage 3) Running cost.

[@AllenHart999]

Total cost, This installation was main done for video purposes so you would need to contact a local installer. i am guessing that answers 1 and 2, Running costs will depend on the heat loss of the property.

[@Honest_Reviewer.]

Great video. We just had underfloor heating put into our bungalow. Taking ages, but it'll be worth it. Thank you for all of the videos over the years. Your videos really helped us make the right decisions on what to buy.

[@AllenHart999]

Thank you very much for your many years of support. Good luck with the bungalow.

[@MrCarhoo]

Allen your a champ 124k subs I remember when it was a like 3/4k congratulations brother.

[@AllenHart999]

Thank you very much for all your support.

[@Maffy-h]

Great video. I'm just about to lay my pipes. Please can you tell me do I need the expansion foam edging on my bifold door cill?

[@okislife80]

The chap is getting things for free as well as lot of reviews

[@AllenHart999]

I need help getting the point? The video says sponsored video.

[@paulbond1666]

Hi Alan I have a Worcester 35CDi greenstar 47 311 94 when the hot water tap is turned on it goes straight to lock or over heating it only does this on the hot water circuit it’s had a new hot water heater exchanger the diverter valve opens on hot water it’s had a new main board the boiler is fine if the pump is wired constantly running all the time does the pump work for hot water or just heating if it’s put back to factory settings and I turn on the hot water tap it climbs to a hundred degrees in a few seconds loads of engineers have been around just throwing parts at it with no fix

[@AllenHart999]

Have you Called WB to see if you can get a fixed price repair?

[@IgorSeremet-lz9gy]

Thank you very much, your video helped us a lot you the best

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@robpaige4953]

Great Video, Im just about to install a Cemfloor liquid screed 60mm thick with 16mm underfloor heating pipework and the installers have asked for a 500g dpm to be put down on top of the 100mm Celotex, so do you know whether the Laminon UFH Grid membrane could be used instead of that?

[@AllenHart999]

You would be best to give the underfloor heating store a call for the best advice. Thanks.

[@briansyme7722]

Not seen much coming up from you Allen. Hope all is well with you. I'm missing the content.

[@AllenHart999]

I have a few short style video,s. I need to get back on it. Thanks.

[@gamereva6413]

Great vid. Do you tee for the manifold off the primary or secondary. Thanks.

[@AllenHart999]

I am going to connect it to the heat and hot water cylinder

[@gamereva6413]

@@AllenHart999 great. Thanks.

[@anjiboddupally4803]

How much is the thickness of the screed??

[@AllenHart999]

it was quite deep, 150mm if i remember correctly.

[@keithbrueton]

How much you changed since you did that cold water snatch 8 years ago , remember me telling you that you could be a teacher ?

[@AllenHart999]

I could never be a teacher, Not smart enough but thank you so much for your many years of support.

[@petersmith2650]

Why did you favour a snake over snail pattern?

[@AllenHart999]

I did,nt design it but the loops are very small, less than 80m

[@necropig]

pretty sure Grundfos don't like their Magna 1 heads fitted sideways like that

[@AllenHart999]

Why

[@necropig]

@@AllenHart999 think the orientation helps them work correctly. Check the book, they aren't shown fitted that way

[@SaqibJavid-l8w]

This is not good leeks

[@AllenHart999]

Why ?

[@SaqibJavid-l8w]

@@AllenHart999 pipes start leaking and copper welds break off

[@AllenHart999]

@@SaqibJavid-l8w i have no idea what you mean.

[@Nickelodeon81]

Indeed, I prefer green beans.