Using Stock Transmitter! How to Upgrade WPL D12 ESC (Brushless & Brushed)

IG: @kuiktip
This video will show you how to connect stock WPL D12 electronic (receiver) to the external ESC either brushed or brushless.
Brushless gearbox installation / if you want to use 3rd Party Transmitter: • WPL D12 BRUSHLESS UPGR...

[@gadogamix]

For the new WPL D12, the electronics are different from the ones in this video, and I don't have the new one yet, so I don't know where to connect the external ESC.

[@robbieaussievic]

..... Well done Mate, don't know why you bothered with sub titles. Your English is fluent and articulate. So envious of multilingual people.

[@gadogamix]

If you don't want to solder the PCB, just use separate battery for the ESC.

[@silvertamman3218]

hello. is it possible to use 3s battery for esc and 2s for stock receiver same time? Obviously with different power switches an circuit.

[@deewill1650]

Gadoga what if i have 2430 Brushless 6300 kv which esc is better 25A or 35A ??

[@miguelromero1854]

Can I just use a plug splitter from the battery connector? Instead of soldering to the board

[@rosaofprague]

This is great. I have a pcb with a blown motor forward reverse chip. The steering is still working fine. Now I just need to get a new external esc to make it work again.

[@phrg8332]

very nice! I'm definitely going to do this! I hope ill somehow still be able to hook up lights though (you ussually plug aftermarket lights into the plug you used for the esc)

[@ACeperienceRC]

Very nice piece of information! 😮👍👍

[@boccacantiga5095]

Great video, all the information i needed!!

[@haajee1]

Very very nice!

[@filsdedieu100]

Very informative video ; thank you :-)

[@bunnintingz]

Hey man if I get replacement stock d12 receiver / esc. Will the stock transmitter work? How do I bind them together ?

[@tedhobby]

I have three wpl D12, and I can use one transmitter for all of three (not simultaneously). It will bind automatically (in my case).

[@aeroelastic6736]

Hi this is a very good video. Will you be able to use similar method to connect a external esc to the MN82 receiver board? Thanks

[@Alennovak666]

Video is grate, explenation also. But i think box is not tat practical. Holes should be facing front to the motor not sidways. Im having dificulties with wires. I did send message to make holes on front. Maybe he will remake it. But exept for that i love the box design and puting it all back togather. Thumbs up.

[@ggwbrc]

Nice video Thanks for information

[@jimsam2]

is it possible to use the xx-339r as an esc? like connect an external receiver to it?

[@bunnintingz]

Hey if I get a stock replacement d12 receiver / esc board. Will my stock transmitter work ? How do I bind them ?

[@meolired]

I got austar ax7s. Problem is i cant upgrade esc because ax7s is an esc/receiver combo. I wonder if you have a way of converting it too. Just need to find the signal wires right? How hard can that be.

[@rccarsanddiyothers343]

also make a video how to brushless motor+RES-v3 receiver and I'm a new subscriber here

[@genesisvillaveza6765]

What is the chip or IC used in D12 board.. i want to find out if its the same with MN99S

[@shippyshank_loves_carsandsound]

thanks for the vid man

[@nathaniel309]

Do you still have good low speed control when using ESC with stock receiver? Thanks

[@but531]

Oh that was cool, i will sub for your work. I will do the same mods to mine if i can.

[@mohamadasriabdulazid4784]

Hi did old board XX-318R support new remote with XX-339R?

[@Rudestude]

Nice can you do a vid on how to do it on the 2021 pub?

[@SevenWelt]

Cool👍

[@nathaniel309]

How is the modulation with brushless esc and motor? Thanks

[@winevibes9996]

Halo om, saya pakai receiver baru, power supply di esc dah ada, jadi udah nyala, tapi kog escnya g mau konek sama receivernya ya? Jadi kedip2 aja lampunya. Rcnya cuman bisa belok.. kesalahannya di mana ya?

[@rccarsanddiyothers343]

what can you suggest servo for wpl d12 because iwant to upgrade my wpl d12 servo

[@daijoubu4529]

Can this be done on the MN stock receiver? How can we tap into the 2 inputs of the motor driver IC TA6586 or do we have to find the rx signal from the transmitter?

[@aeroelastic6736]

@daijoubu4529 have you ever found about if the MN stock receiver can do the same thing? Thanks

[@daijoubu4529]

@@aeroelastic6736 i made an Arduino that does the conversion, I can share my code, you'll have to solder 4 wires

[@mhelborn73]

Sir hkw to install brushless motor to stock esc of wltoys a979

[@wa2lou]

Tu peux faire une vidéo avc les soudures sur la carte 2020 je comprend pas

[@pinoyOZBoyCutie]

is it the same process for brushed ESC and motor?

[@user-lk3dl4mc9j]

Hmm.😤 perasaan kemaren ada yang bahasa indo

[@Fantaman900]

display shows 2055 rpm yet the man says 20,055 rpm. small difference🤣