Using your DeWALT DW734 Planer

In this video I will be unboxing my new DeWALT planer. I'll talk about some of the functions of this particular planer and go over how to use it, some do's and don't's and then we'll give it an honest test run by cutting and planing some strips for a cutting board I'll be making in the next video.
Remember to use the lock bar! I noticed I didn’t use it a couple times in the video. I was still getting used to it. This is an important step as it will leave less snipe on the wood.
-- LINKS --
(As an Amazon Associate I earn from qualifying purchases.)
Tools/products used in this video
► Dewalt Planer: amzn.to/3Nl5aTZ (Amazon)
Software, websites, and plugins used
► TubeBuddy: www.tubebuddy.com/greentree
If you’re interested in seeing the finished cutting board in this video, the video in the link below will show you step by step how I make them! Enjoy!
• Making a DIY cutting b...
DISCLAIMER: This description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows us to continue to making videos. Thank you for the support!
Go check out how I made this amazing "coffee bean" serving tray!
► • Walnut and Epoxy Resin...
Instagram: / greentreewoodworks
Music in this video is from Epidemic Sound:
00:00 My Town - Jackie Martin
2:51 Segla - Jerry McHoy
Keywords:
Wood Planing, DeWALT planer, product review, wood plane, resurfacing wood, woodworking, How to plane wood, cutting boards new tools, wood planer, Justin Turpin, Green tree woodworks

[@greentreewoodworks6172]

Check out the EXACT model planer shown in this video here!!! amzn.to/3Nl5aTZ (As an Amazon Associate I earn from qualifying purchases.)

[@pwolfpapaw8474]

Thank you. You answered my question. It is a turret stop.

[@joshwatson9064]

Thanks for the video. Just purchased one and watched this while unboxing it.

[@craigabel3674]

Don't forget to push down on the lock before running your piece through the machine. It will stop the gouge (snipe) on the leading edge.

[@greentreewoodworks6172]

Thanks! I did notice I failed to do that while planing in the video.

[@craigabel3674]

No problem, my son has one and I figured it out after using it for a few projects

[@am1manTravel]

Seems like a real pain to have to lock and unlock it for each pass after making a very slight adjustment.

[@durbdeedurb]

Thanks, was wondering about that!

[@ackflak]

Considering purchasing, this was a great intro. Well done and thank you

[@greentreewoodworks6172]

Thank you for watching!!

[@durbdeedurb]

Thank you for the tutorial!

[@greentreewoodworks6172]

My pleasure!

[@1620GarageAndFarm]

Nice review !! I just scored this same planer, plus a delta jointer for 140 bucks @ a local yard sale !!

[@greentreewoodworks6172]

Very nice 👍🏼

[@MystiqueULH]

I wouldn't let my kids get near this power tool. Kids will put their hands anywhere to explore and this things has extremely super sharp blades in it.

[@slimmonty4477]

Neat

[@jashimuddin7716]

Thank you

[@Dc_tech386]

So I replace the in feeder roller with a metal roller I machine it work like magic so no need to every replace it cause the a new rubber one cause 100 box so it's a way you can look at

[@Damon_Barber]

I like the Mr. Rogers Neighborhood background music! Very relaxing!

[@CharlezMalasana]

It’s called jazz brother.

[@danielparra6314]

Was wondering, do you need to remove the dust collector piece when you put it away, if you raise the blades all the way?

[@greentreewoodworks6172]

You know…I would think so but I’m not really sure…? My planer is in storage until the new shop is built but if I remember I’ll find out and reply back to this comment for ya. Thanks for watching!

[@mariapullins4698]

Can you put a cedar log that has been cut from above 12" long to shave the bottom end to set level?

[@greentreewoodworks6172]

If I’m understanding the question right…I think you can by using what we call a “planer sled” and use super glue/shims to hold in place to get one side flat. Then when you have the one flat surface you can flip it over and run it through without the sled. I hope that answered your question!

[@grantwes]

You didn’t have the Lock bar down. You could see the plainer moving UP as you ran each piece threw the plainer. If you would have had the bar down you would not have gotten the missed section or Snipe

[@greentreewoodworks6172]

Yes I agree, I noticed that after I had already posted the video haha. I've used this planer hundreds of times since I made this video and I've used the lock bar every time since then. 👍🏼

[@ronaldguy5474]

What's the dial for on the right side? I'm thinking about getting g this one. Thanks in advance.

[@greentreewoodworks6172]

That dial is a turret stop. It prevents the planer from being lowered too far. For example if you're using a planer sled and have thin pieces it'll prevent you from planing your sled. Thanks for the comment!

[@markmurto]

The latest Dewalt dw734 does not come with the 10mm/8mm wrench, or place to put it. Its called Type 20 i think as opposed to type 1.

[@peterfryer6915]

I was wondering where my wrench was. Just picked it up this morning.

[@markmurto]

@@peterfryer6915 what is the wrench used for anyway?

[@peterfryer6915]

I assumed it was for the 4 bolts under the feed tables but I'm not certain

[@markmurto]

@@peterfryer6915 Well, the holding place is eliminated on the model 20 tool tray, but you can get a model 1 tool tray for $14 on eParts and its an exact fit. You can even get the stickers. I was bummed when Home Depot sent me the model 20, but the wrench I can do without I guess.

[@greentreewoodworks6172]

That’s good to know. The Lowe’s closest to me still has the “type 1” on display but I’m curious to see what’s actually being sold. 🧐

[@jessealvarez8893]

Why didn't you just run the intire board so you don't have snip?

[@greentreewoodworks6172]

Hindsight (and how I do all my work milling) I would’ve cut the whole board to the desired length, planed it, then cut it into strips. I’m not gonna lie, this was early in my woodworking journey and I didn’t know any better 😅

[@bucketofsteam9260]

If you're an idiot like me, make sure you don't unlock that bar with the head too far up. Your fingers will appreciate not being slammed between the bar and top hood.

[@greentreewoodworks6172]

Haha I never thought of that. I bet that would hurt. I usually only plane 4/4 boards and sometimes 8/4. But nothing big enough to raise the head up that far.

[@manny3549]

Small children and power tools are not a good mix. They don't know the difference if it's powered or not especially when daddy is at the lumber store.

[@rafalski101]

Working part not blocked ⚠