How to DEEP CLEAN / Refurbish a DIRTY Shark Navigator Lift Away Vacuum

[@kanita0958]

Housekeeper here, pro tip: but a mesh laundry bag, put your dirty filters, (hepa and cloth filters) in it and wash them in the washing machine. The mesh protects them. I do this at least 3 to 4 times a week to keep my sharks clean after each use in my clients homes. Then air dry them. Same for the canister, a pressure hose will clean the mesh filter. All my vaccums have suction as of they were new and I use them A LOT!

[@nyscurls08]

How do you clean the brush and bottom of the vacuum?

[@JoeBlobA]

@@nyscurls08 I run a motel, Idk about this model, but most of them you can unscrew the bottom. I take a knife and cut straight through the hair and carpet strands using the plastic on the brushless portions as a cutting board, then I can pull it out of the brush portion. My mom always used scissors

[@girlcalledsun1719]

This video was a lifesaver for me today - thank you! I depend on people like you to teach me since I don’t have my dad around. Thanks for your help!

[@alloverdaplace2043]

Damn that was sad about no dad thing. 😕

[@alexvids9232]

Sorry for your loss. I'm dreading losing my dad. 😭

[@Vikassy]

@@alloverdaplace2043 q11d

[@msmalloryb86]

I'm so sorry for your loss. I completely feel you. We just bought our 1st house in Nov 22, my husband suddenly passed 30 days later 5 days before Christmas to be exact... my whole world has been turned upside down 😢

[@CH.2024.]

Brilliant video. Female operator here -- and this helped me so much! thank you!

[@VacuumWars]

Great to hear!

[@shyanngoss6589]

Total lifesaver for me today!! I couldnt figure out why my vacumn wasnt sucking up, it was just spitting out and making a whirring sound, followed your video and in the bottom hose it was soooo clogged! The whirring sound is gone and it picks up, but I feel like it was still spitting some out behind me when I had the carpet setting on, but when I switched to the floor it was fine. As long as I go over the floor slowly to allow it to pickup on the carpet setting, it will pickup and not blow back. THANKS SO MUCH!!!

[@rodneyclements4386]

Thank you for taking the time to post this very informative information. Took our daughter's Shark apart per your instructions, to repair the beater bar. The 2 screws located underneath the 2 small drive wheels would've been an issue with disassembly. Thanks again!!

[@mandyjb77]

Thanks for video. Truly a deep clean. I have this exact model after all these years. I have a spare filter set I bought and that way I can replace them while the other is being cleaned and then dried. I don’t think mine has ever gotten as dirty as this one. I will say I think it’s easier to go ahead and dunk the debris bin in soapy water and wash it that way (a small angled brush or bottle brush would probably make it easier). I just leave mine to dry overnight after I attempt to dry it off. The two things I dislike about this old model is the lack of lights and that part in the bin where the dust/hair gathers and I almost always have to stick my hand inside to remove the glob. We do have kitties and two long haired people here, but still...the professional Shark/years newer model, they worked that kink out because the bin is easier to empty on it. And my newer one has lights. I really wanna upgrade to the DuoClean as soon as we’re able. I feel behind in the vacuum times. 😆

[@rychei5393]

I am surprised you didn't use a bottle brush inside of the hose. These are great vids, I'm loving them, thank you!

[@anthoniewyrick5203]

I use long bendable bottle brush on mine💯👍

[@laquerisma]

Looks like they vacuumed the barn with it.

[@judymontanez2676]

Judy here, This was just what I was looking for. Great Video, clear instructions you made it seem so simple. Love my shark, Your the best. This was my first time watching you, I subscribed. Thanks!

[@marnelvt]

Thank you so much for this video! My mom gave me her old Shark as she upgraded but it needed a reeeaaally good clean! It’s like a brand new machine!

[@VacuumWars]

Awesome!

[@amandapack9018]

Thank you for the video! Very helpful! My work was throwing one away...All it needed was a cleaning and a new roller!

[@mikekufner1192]

Love this! now I can deep clean my own every few months to make sure it stays in maximum working order for as long as possible. My house is so dusty this thing gets kinda gross fast. Not nearly even 20 percent as bad as that one but still, my wife's hair is everywhere so there's lots of hair and dust. My wife loves this particular vacuum. She says its the best she's ever used.

[@panoramic_life38]

Thank you for the video! I was having a hard time 😫 I didn’t know about those hidden screws 🤦‍♂️! I appreciate the video 👍 thumb up

[@TehKitteh01]

Just wanted to say I bought one of these vacuums used over 3 years ago and it's the best one I have ever used. It hasn't missed a beat, even with having 2 cats. It gets all the fur out of the carpet and furniture, no problem.

[@ayo509]

Does it still work

[@TehKitteh01]

@@ayo509 Yes! The seal around the canister came off, so I had to replace that but it still works like a champ.

[@shegimmienerd]

@@TehKitteh01 what vaccum is ir that u have?

[@TehKitteh01]

@@shegimmienerd Shark Navigator lift away.

[@ah244895]

Abrupt ending. Soaking the main canister in hot soapy water would seem to be much more efficient. Blow drying with an air compressor would efficiently remove all water and prevent any future rusting. If you were doing this frequently, get an ultrasonic cleaner, makes work work of embedded dirt.

[@stephaniepumfrey545]

That's what I did

[@shaynamaewallace3797]

I was gifted this vacuum almost a year ago, used, and just now found out about the "lift away" and long extention handle parts 🤦‍♀️

[@lkw5699]

After watching your video I was motivated to clean mine. I had so much hair wrapped around the brushes I haven't looked at in a year. I cleaned all the hoses and main dust bin out. It now sucks up dirt like it is brand new again

[@Prospermiinow]

Thank you for taking the time to share this video. You have truly helped me. So very grateful. Be Blessed.

[@karenhartley5685]

Thank you so much for this video. I hope it helps me to save my vacuum cleaner! I appreciate all of the effort in the details that you put into this video.

[@elizabethswarckof7899]

Thanks so much! I could not figure out how to get the brush roller out to clean behind it. I never would have thought there were screws behind those little wheels!

[@anthonystreeter7217]

Thank you for the video. We have a 5 and 3 yr old so we use the vacuum A LOT! They're pretty expensive for a descent one so this is good to know to keep it lasting.

[@VacuumWars]

You are so welcome!

[@johnerlinger3744]

Great video. I learned a couple of helpful things. I used my hair dryer to ensure all the parts were dry before assembling.

[@Sam-dd7tn]

Thank you. Mine isnt nearly this bad, but I like to do a deep clean on my vaccums 2x per year and wasnt sure about this model.

[@MystiqueULH]

I have a long dowel and in order to clean the house which is flexible as it is I put a sponge on the dowel and ram it thorugh the hoses by stretching and then gathering over the dowel and sponge then rinse it out with a strong stream of the hose - works like a charm

[@dawnwitt7633]

Just came across this video. Excellent! Thank you 🤗 Just a note, I used a tide pod and white vinegar in hot water to clean filters, soak hoses and wipe everything down it’s all like new again. Rubbing alcohol worked nicely on clear plastics after I rinsed

[@VacuumWars]

Thanks!

[@dawnwitt7633]

@@VacuumWars I have a bit newer shark NV 391 26 and the brush roller and the motor are attached to the clear plastic inner casing. I can’t figure out how to get the brush free from the clear plastic case 🥺

[@NatachaPoggio]

Your video was very helpful, thank you. I haven't had a deep cleaning to my vacuum since I bought it 2 years ago, so I learned a lot about the parts I need to maintain properly. One thing I felt could be improved is to use biodegrable detergent (because the one you use will be bad for the soil in your yard, and the environment, and it will send a nice message to everyone following your instructions). Thanks again for being so throurough.

[@51623allissa]

I actually found mine next to the dumpster of the community. That's insane. It still works although had some obvious where and tare but was not nearly as dirty as as the one in this video. Thanks for showing me how to clean it. I've wanted one of these for YEARS. They're expensive though. Thanks again for making this video.

[@Arizona-360]

This is my 2nd time watching as I clean my 10 year old shark lift away vacuum. I used a bottle brush to clean in the hose areas and it worked great

[@wowowiiwaa1337]

Wow you go all out! and I thought I cleaned mine good enough. Glad I checked your video out!

[@darkknight145]

Just an FYI, the later promo videos from Shark indicate you can wash the HEPA filter under a tap.

[@herbfellows6435]

A 50 cent brush from Ikea does a great job, the bristles are deeper than a toothbrush but yet somewhat flexible, and the brush handle is much stronger than a toothbrush.

[@lilysnana1955]

Thanks for a great video! I couldn't remember if I should wash the felt filter (having misplaced the owner's manual!) so this was most helpful. When you discussed blockages, though, it reminded me of the time my Shark just wouldn't pick up anything and my husband was all set to go buy a new vacuum but I knew there had to be something going on. I took off all the hoses, as you recommend, and found a Bic pen caught in the U bend! It was tricky getting it out, but so worth it since the machine works great again! That was several years and two houses ago, so I'm really pleased with my Shark investment!

[@VacuumWars]

Awesome! Glad it helped!

[@acuchemkid2007]

I have this vacuum as well and cleaned it recently. One thing I did to not get the hoses wet was use my extra long dryer lint brush and run it through the hoses.

[@heatherprincipe9972]

Thank you. My first shark was the one in this video and what I have now is purple. Both state in instructions to rinse filters with cold water. The first one I put the filters except the hepa in the washing machine a few times before reading not to do that. I used either hot or warm water. After that would hand rinse but with hot water while putting a cleaner in the filters beforehand at times before rinsing clear. The purple I only rinsed but with hot water. Since instructs cold water I will use at least luke cold.

[@karenvaught3995]

Good on you for keeping these out of the landfill.

[@lisahauff4683]

I followed your example and saved myself driving it to the vacuum place to be cleaned. Thank you!

[@VacuumWars]

Happy to have helped!

[@Emmisullivan14]

I just bought this today. I love it!

[@kimjackson1052]

I was pretty frustrated when I couldn't get the cover off, & this video calmed me down.. I love LOVE my Shark! I also got it used. It wasn't near as dirty as the one you're working on. I've made sure I have a couple filters at least, that way I can wash the first one & let it dry completely, & put the 2nd one on so I'm not without my vacuum for the 24-48hr dry time. It works really well. Someone here mentioned getting filters on Amazon & I did that as well. Life savers! I have to cut my 30" hair off of the Brush roll OFTEN lol, but doing proper maintenance has kept my vac like new for around the four years that I've had it. & Lastly, my husband was so impressed with my Shark Nav Lift away that he bought a 2nd one, used as well! Now he can clean up the messes from his builds, projects & other things any time he needs to, which is really helpful! Thanks again!

[@carlosmalone1428]

BEST VIDEO EVERRRRR 🤪 easy and to the point TY 🙏❤️

[@sweeperkeeper9550]

My aunt has the non lift away version of this and only cleaned it once for the about 4-5 yrs of having it and I tell you the filter was WAY worse than that sooooo I took it upon myself and she brought it over and it it was SO bad and currently the filter is drying so I think it’s gonna work so much better!

[@pauljs75]

Curious... When did they change from the "donut" filters on the NV series? The old ones had more surface area for filtering and honestly weren't all that hard to clean. (Now I'm wondering if it's still easy enough to get them?) Other than that, it's better to clean the filter after every three uses instead of three months or so. Keeps a significant portion any really fine material from getting to the motor and that's what can eventually kill the vac in the long term. Looks like whoever had that one last never really stayed on top of that part of maintenance. Also to clean out the hoses from anything that sticks after using some soap, a soapy rag with string tied to it. Thread string through and bunch up the rag so it's a bit hard to pull through but not completely stuck. Pull that through the hose back and forth a few times to floss anything that may stick if rinsing doesn't do it.

[@cjuengel8747]

Thanks! I was just about to go to a repair shop before I found this video, it works like new!

[@VacuumWars]

Great!

[@bethgork7332]

Thank you! I just bought mine, have 2 large dogs & it’s been raining…I try to clean their feet before running around inside…but still dirt & OMG my new vacuum was filthy after 1 use…until I found your video. Thank you so much!! ❤

[@VacuumWars]

Thank you!

[@howardcarver1415]

Oh Happy Day! when I found your video for my specific need! Thanks much for your help with this Shark vacuum cleaning process. I was ready to give up attempting to clean it myself. 🤗

[@VacuumWars]

Glad I could help!

[@timtableman5434]

Genius editing. Thnk u sooo much for fast fwdng the unneeded parts of the vid.

[@VacuumWars]

No problem 😊

[@krinsyn6396]

thank you for this tutorial! i was able to extract and clean the vacuum brush =)

[@lilleysnider293]

Cute little helper!! Terrific tutorial!! Thank you!

[@douglasswright484]

I had a smaller, older Shark🌼 that would clog and not even move on my thick wool carpets. This new Shark is amazing!!

[@johnmolyneux228]

Thank you, the video was very helpful! I to need people that know to teach me how to do think correctly.

[@sugarpuffnstuff]

Thank you! 🙏🏻 Appreciate the very thorough instructions! Now my vacuum works great! 👍

[@VacuumWars]

that is great!

[@susanlahti2702]

I am having problems putting the wee little wheels from the bottom back on. The ones at the very front that you took off to get to the screws. They don't seem to want to pop back in. Anybody? Any suggestions? Never mind. Thanks though but I managed it. And....it's done. So glad I saw this video. Helped tremendously.

[@danbale4160]

Considering some of the comments here: * The dustbin can be washed out. I take a hose sprayer, set on "Full" or "Jet" and have at it. * All three filters are supposed to washed out with (cold) water; I use lukewarm water. ** I'm surprised the HEPA filter doesn't ever get replaced. I find it interesting that water doesn't flow through the HEPA filter. I fill it with lukewarm water and let it sit in the sun for an hour or so. Flip it over to drain it, then take a hose sprayer to rinse out the loosened stuff. * I don't use any soap, per the owner's manual, but I might be tempted to use a light mixture of Dawn dishwasher detergent and warm water on the two pre-filters. * My Shark (ZU560) keeps the roller brush free of hair, so I don't have any real need to remove it. (We have three cats and a dog; let the reader understand!) It would be nice if it could be *easily* removed so I could sanitize it every once in a while. Instead, I lay the entire vacuum unit outside with the bottom facing sunward, turning the brush a quarter turn every 15 minutes. Ultraviolet rays from the sun is a great sanitizer! * I also let the sun dry and "sanitize" the filters and the dustbin. * Regardless of the sun drying everything out, I still wait 24 hours before using again. * I found the owner's manual for my unit online. (Some comments mentioned not having one.)

[@joeheukensfeld9924]

Had no clue the metal mesh filter inside dust cup could be cleaned. Just saved buying a new vacuum. Thank you.

[@viajerozz]

Great video thanks! Question: Why not clean the HEPA filter under water? Is it full of carbon? Mine ran pure black when I did it with water per other videos.Thanks!

[@Alexscott100]

How did you get the hose to dry out any way other than air drying

[@zyberjunker]

Thank You so much for your VDO. how to. My problem was the hidden screws under the little wheels. I can see why people just rather throw the nonworking appliances in to trash. Take time and patient to fix. What are we going to do without people that like to fix things.

[@chadmorgan5046]

Thank you for your video, with your help I was able to properly clean my shark and get it running great again.

[@blastw0rks]

I Like The Fact The You Explained Every Thing And Took Your Time I Have A Shark Nv46 Navigator Lift Away Have Had For Long Time It Was Brand New At The Time It Still Works Just Like It Did When It Was Brand New Just Recently It Need A New Bottom Hose And Dust Dirt Bin Cup Thing And It Has Not Need A Belt Since I Have Ownd It

[@VacuumWars]

Great to hear that it has been a good vacuum for you! Thank you!

[@Bennythecoredriver]

Would have been nice to see the finishing product lol

[@MuMu-fu7qe]

😭

[@elizabethconley4996]

Love your video! Definitely helped my confidence to do clean my own shark

[@VacuumWars]

Awesome! Thank you!

[@soupwifey]

Thanks for sharing this. It helped me a lot.

[@SexyMexiChili]

would have been nice to see the vacuum all cleaned and put back together! nice video though. I will definitely be doing a deep clean of my vacuum soon.

[@01Dirtnapper]

Great info since I have to do the same process and the screws under the wheels and sticker would have been the last for me to figure out!

[@mandamargh]

This was exactly what I was looking for! Thank you! Great video!

[@Kamiiiiiiiiiiiiiiiiiiiiiiiiiii]

you can use a dryer vent brush to clean out the middle of those hoses. Best vacuum I ever had was the Fantom. Lasted a little over 25 years. I have the Shark Liftaway now, def. not as good as the Fantom, but works! Wish The Fantom Was still around!

[@VacuumWars]

Great tip! and thank you!

[@paulhart8140]

Great video! Helped a bunch, thanks!

[@thewizardofchinohills7277]

WOW! I Surmise That Reconditioned Sharks Are Big Business. You Spent a Little Time On This. Pretty Cool.

[@jenk6895]

Wow! Whoever owned that vacuum did NOT take any kind of care of it obviously! I’ve never seen a vacuum this dirty! Gross.

[@Thatgamerfurash]

Jen K I’m 15 and I have the same vacuum literary and I keep mine extremely clean

[@eileenfuentes6975]

I bet the yellow orange gunk, almost a rusty color-- is from someone vacuuming up soiled places with pet urine. For it to turn that whole cartridge that funky color - - - I'm willing to bet whoever owned this vacuum used that cheap scented carpet powder to absorb cat or dog pee and would vacuum it up. And wherever else they'd vacuum that filth in the bristles and on the bottom of the vacuum would spread through the rest of the house. Yuck.

[@eileenfuentes6975]

@@Thatgamerfurash wow a kid that not only vacuums, but a kid that owns a vacuum and keeps it clean? shout out to your parents for doing a good job lol How often do kids end up on this side of KZbin? watching and commenting on videos on how to clean your cleaning supplies so that you can have a clean vacuum to clean with and live in a clean home... lol I'm impressed!

[@Thatgamerfurash]

Eileen Fuentes well when i turn 18 ill be out of the house so i got almost everything i need

[@xeserupseinopelttil4574]

Same. I've owned mine since 2015, only cleaned the filters once, but periodically clean the bottom out. It's a bit dusty, but not overly disgusting.

[@peteallennh]

Fantastic video, thanks a million! This is exactly what I needed to know.

[@VacuumWars]

Glad it was helpful!

[@donb1979]

My god what on earth did they vacuum with that? They must have one nasty house

[@zoinks5717]

Pretty sure they use it for like business and stuff

[@jellyjordy1154]

That’s what mine looks like, except the bin and filters are cleaner

[@-Bellana-]

This was perfect! I was worried I wouldn't find a good video for this! Lol thanks!

[@VacuumWars]

Glad I could help!

[@johnmule9419]

Nice, professionally done video..really helped me a lot.

[@VacuumWars]

Great to hear! Thank you!

[@halakennedy4706]

Great video! Thanks for all of the tips. I'm actually about to deep clean mine now. I was wondering, maybe you said it in the video and I didn't hear it, why can't you just wash out the canister? With water? Should it not get wet? I was trying to read through all of the comments to see if anyone else asked but there are so many! Lol!

[@lindamorgan2678]

I was thinking the same I see someone else above mentioned to just wash it out

[@KELLSEY444]

I just wash mine out with the garden hose. Clean the center cone part with a detail brush. I've only done it on a hot summer day, so drying it hasn't been a problem. I guess I would use the hair blow dryer if necessary.

[@lindamorgan2678]

Thank you Good information .. Is there any reason you cannot just wash the canister with soap and water and let it dry completely? I would like to sell mine and make it look very clean Thanks again

[@steventhehistorian]

Thanks for making this and sharing!

[@fluff1353]

I have two Sharks but mine are newer. The taking off of the plating to reveal the brush is different. It is hinged with three quarter turn releases instead of screws. The trick is trying to clean the layers of pet hair, dust etc that build up along the intake cover and the stand up bristles behind the roller. Short of completely disassembling the entire head, it is a chore to clean effectively underneath.

[@itsGaiaPeralta]

Mine is newer too and I wasn't able to take it off with a screwdriver were you able to get it off? I had to cut and yank all of the nastiness out it was so draining.

[@fluff1353]

@@itsGaiaPeralta I think manufacturers encourage us to take the sweepers in for maintenance. Most models I've seen have screws within the turner brush housing that need to be removed to get the roller out completely, but require a special tool. The way the newer models are, you can only disassemble it so much and clean it so much without some kind of professional tools. Yes it ends up being a major hassle to clean the roller housing effectively. I guess cleaning it regularly from the start would help a lot.

[@monty3503]

That is the dirtiest vacuum i have EVER seen, i would never let my own shark vacuum get that dirty!!!

[@HelloCarolineKate]

I know and imagine they were not too ashamed to sell it 😯

[@blastofo]

I found one and cleaned it and it was beyond disgusting. I had to pull out a dozen handfuls of someone elses hair. It was all jammed up in the roller. Had to cut it out with a razor blade.

[@sandramullen7804]

@@HelloCarolineKate exactly. You would clean it all up before selling. And if they had done that they wouldn't have had to. 😂

[@dawnedalzell4545]

Thank you. You did a wonderful job demonstrating. My vacuum is like new.

[@VacuumWars]

Awesome!

[@AmyB.]

Thanks. Didn't know I could take the brush out. That may help.

[@MakingSawdust]

A gasket showed up in the bin of my NV357 and I'm trying to figure out where it came from so I can glue it back in. My best guess is the end of the short hose that connects into the brush roller. Very similar to what you are holding at 14:02. Thank you for any thoughts and your time.

[@emmachuang776]

Shark Vacuum Filter Replacement:(www.amazon.com/SHJIUPO-Replacement-Compatible-XFF350-XHF350/dp/B07Q33R8PN)

[@ashleyblack8962]

Very educational. Thank you so much.

[@gigismith1362]

TIP..... after soaking and scrubbing the inside of the hoses and parts with the best cleaner for the job- which is DAWN..... run a little bleach and water solution thru hoses/parts. To disinfect. To Keep yourself and your household healthy. Don’t forget to spray Lysol (if you have it) onto those filters while they’re drying to kill bacteria

[@bubl8015]

My Shark NV360 Navigator Lift-Away Deluxe has security screws so I had to buy a set to remove he screws. They were 6 sided - nice Shark!

[@jagjit86]

Exactly what I needed. Thank you!

[@VacuumWars]

Glad it helped!

[@Sam-dd7tn]

Btw, do you have a link for the little band inside the spinning hand tool? For some reason mine is stretched out and now the little brush bar wont spin..

[@Sam-dd7tn]

Connie White okay. Maybe i will have to buy a replacement hand tool. Thanks for the reply! 👍

[@herbfellows6435]

Don't know if anyone else has mentioned this, but I use a leaf blower outside (you could also use a hair dryer on cool, but a lot less powerful, or a can of compressed air which gets expensive) to blow out the initial dust and then again after each time I clean something inside. Just be sure to point it away from you. Works a treat.

[@MystiqueULH]

If you are a diver and have scuba tanks there is an attachment for just dust blowing that absolutely does a great job. Short bursts will clean a lot of junk out. I also use it to blow dust out of my computer but with a bit of distance cause you don't want to blow anything off of the motherboard.

[@seanmcaleavy2369]

I have an air compressor, with a 50-foot hose, that is always turned on at my house. I use it for my nail guns and tires and to blow the dust off of things. I blow out the filters every time I empty the cup. It takes less than a minute.

[@NisiMichelePhotog]

Great video instructions my vacuum thanks you so much!

[@Hc80578]

I own a shark nv70. The instruction manual for mine says you CAN rinse the HEPA filter under the water dirty side up until it runs clear. If I want to clean the filter inside the dust cup with a scrubby green pad as shown do you need to use soap with it or just plain water to remove the dust from it??

[@soniamedrano4417]

Thanks, awesome video and good information.

[@ToothBrush531]

Can I get the actual container part wet? I’m thinking about just soaking it to get it clean.

[@geraldinechapleski5495]

Do you happen to know what the (clear) tube with the spring in it is for (12:30ish on the video) attached to the top of the casing for the motorized brush assembly? I have it attached to the part that would suction the dirt from the floor, but not attached to anything on the other side. Yet, it was full of dust/pet hair? Is it supposed to connect to something? Thanks!

[@cwhitmore88]

Worked for me. Thanks!

[@VacuumWars]

Glad it helped!

[@GenericGi]

Excellent video. Still relevant. Well done!

[@eyeonart6865]

This video was so helpful! I would buy a used vacuum from as as you are so complete restoring.

[@blueoyster8892]

Thanks for the tutorial...great information to know..thank you😊

[@VacuumWars]

Glad it was helpful!

[@kyracarsonmusic]

Hello. I accidentally rinses the base where the HEPA filter and cord is with water without thinking about it. If I dry it with a fan, can I still use it without electrocuting myself? Thank you.

[@nikkinj]

Love a shark vacuum but the brush roll cleaning is ridiculous.

[@jonielynnperry1990]

I did this to mine. After putting it back together the brush will turn for a second then stop. It won't stay spinning. Is there something I should look for that I may have done wrong putting it together?

[@KM-bt5oz]

Purchased my filters Amazon. Cheap all the filters are available. Love my shark!!!

[@AWiz-lx8lh]

Great Job and Video Mate. Impressive!

[@VacuumWars]

Thank you!