Volvo D13 no crank no start/ Bad ECM replacement

D13 engine died while the truck was driven , after driver wasn't able to start it! Inspected all the wires that goes to the batteries to the starter and to the alternator, everything was fine , tryed to bypass the starter, it was cranking the engine but still no start, after inspected all fuses, fuse FE 4 were blown, (ignition fuse in the box in front of cabin, replaced it still no start, after removed the upper wiring conector from ecm everything was fine, tryed to remove the Lower one and something was holding it! Tried to pull harder and it came out with one melted pin, plastic around that pin on ecm was also melted on the conector everything fine! Is a probability that was a short inside the ecm olson that was a short somewhere on the wiring harness, replaced the ecm from another one from another truck , and it started , everything is fine!!! Did anybody had something similar?
If you have any questions let me know in the comments below!
More repair videos in the playlist on the link below:
• Meritor differential d...

[@sigbaw4510]

Replacement ECM does not look new and it still start without programming.. now I know its possible.. thanks for your video, keep uploading bro

[@valeriumoscalu7580]

It's going to start only if it's going to be from the same engine and the same year! If not you will need to reprogram it!

[@mcmariolomza8744]

​@valeriumoscalu7580 can you program used ecm with PTT?

[@valeriumoscalu7580]

Yes!

[@Saidi-zd3ot]

​@@valeriumoscalu7580how we can do it Can u share us a video for it

[@Jere_Bear9]

Same thing I just said lol I guess that's if it's not deleted tho

[@themaestro7922]

Looks like Pin B57 of the EECU broke off in the harness. Pin B57 is a power supply. Most or all of the pins on that end of the B harness and that end of the A harness are for ECM power or ground. This is why they are bigger than the rest of the pins. And wow. It clearly got very hot.

[@mjyouletstalk.6724]

Thank you!! Sir for sharing

[@themaestro7922]

Good info in your description

[@valeriumoscalu7580]

Thanks!

[@user-ie7sp3ij9c]

Hey man my truck is a 2012. It was running fine with check engine on. I went on vacation for a week and when I try to start it the lights would come on, but it won’t crank at all. The only message i get it Maintenance required vehicle Ecu. And j1939 Communication error with Engine ECU. Please help me out with this if you have any idea what could it be

[@johneynoneck]

My Volvo FM 9 turn or hold key ignition light up but no start or intermittent

[@fernyc6711]

My ecm is not melted all the way u think it’ll stil work ?

[@gersonacevedo4495]

Hey I had the same problem (crank no start) on a 07 volvo d12 and I replaced the ecm for a different used one with the same part number, now it starts only when primed and accelerates fine then dies seconds later. Does that mean I need to get the ecm reprogramed??

[@valeriumoscalu7580]

Usually if its removed from another truck that is the same make and model it should work fine! If I'd doesn't you can try to reprogram it! Are you sure you don't have any other problems?

[@user-ie7sp3ij9c]

Hey man my truck is a 2012. It was running fine with check engine on. I went on vacation for a week and when I try to start it the lights would come on, but it won’t crank at all. The only message i get it Maintenance required vehicle Ecu. And j1939 Communication error with Engine ECU. Please help me out with this if you have any idea what could it be

[@phillipslattery3260]

@@user-ie7sp3ij9c same here brotha

[@user-ie7sp3ij9c]

@@phillipslattery3260 It was bad ecm

[@johndilinger3063]

Hi Valeri I have a problem with my Volvo D13. I was hoping you can help. How can I get in touch with you? Thank you

[@valeriumoscalu7580]

You can text me: 4253991589

[@johndilinger3063]

@@valeriumoscalu7580 thank you.

[@drazenkaralic1827]

did you have to program the new ECM once installed

[@bikerboy2k142]

That ground on the ecu does it ground to the block where the ecu bolts in or do it bolt some where else?

[@mihailbejan8202]

Valeriu salutare. Pot să intreb dacă folosim un ecm uzat dela motor asemanator cu aceiasi ani aproximativ. Este nevoie de reprogramare sau avem sanse să pornească fară? Si dacă este nevoie de reprogramare cum de reprogramat ? Prin remplace hardvere sau new software ? Mulțumesc anticipat.

[@valeriumoscalu7580]

Daca e acelasi an si acelasi model trebuie sa mearga fara reprogramare!

[@mihailbejan8202]

@@valeriumoscalu7580 da dacă nu merge avem sanse să-l reprogramăm fară dilear oficial ? Si prin ce dacă stii ? Remplace hardware sau new software.

[@user-my8op2lm2z]

Hello engineer, is it possible to control? P05..Works somewhere P03

[@andreyonushko5405]

Good day! Tell us the 2017 VOlvo FMX D13C 420 engine. Burned out control unit! can we supply with FH 2012? D13A 480

[@henrylopez5332]

If the Ecm it’s not connecting with the scanner and it’s ground and power wires it’s a bad. Ecm?

[@aditya03ify]

This DG look like factory tech tool

[@shaznmohamed5266]

Hi i am from sri lanka

[@Farshad._.]

Your idea from fe04 idem fe40 ?? Because power of EB57 electrified from F40 Can you elucidation to me? Thank

[@aditya03ify]

Hi. Which diagnostic tool are you useing.

[@lanceturner352]

I'm the same issue, in my truck, i can get to gear 10 and the truck starts to sputter out.. i was told it was my ecm at the volvo shop, its costing me 3500 for a repair.. is that right?

[@valeriumoscalu7580]

Yes, at Volvo shop price is approximate like this! I the ECM it's around 1200 and it should be programmed !!!

[@bth9101]

Just had mine go out. Costing me $3000. Got to get it programmed all over again and get the DEF off it AGAIN.

[@juanwaysniper083]

@@bth9101 so one you get a new one a program it. It reactivated the DEF?

[@juanwaysniper083]

@@bth9101 once

[@user-ie7sp3ij9c]

Hey man my truck is a 2012. It was running fine with check engine on. I went on vacation for a week and when I try to start it the lights would come on, but it won’t crank at all. The only message i get it Maintenance required vehicle Ecu. And j1939 Communication error with Engine ECU. Please help me out with this if you have any idea what could it be

[@xiangzongshi3953]

How much for this parts

[@valeriumoscalu7580]

800 for ecu + 360 for programming +work!

[@user-ie7sp3ij9c]

Hey i have a 2012 vnl. Its not doing anything when i try to crank it. Its giving me this message along with check engine light. J1939 communication error with engine ECU. Any idea what could it be?

[@themaestro7922]

Did you find the problem? Was it the ECM?

[@valeriumoscalu7580]

In my case was the ECM

[@270lilmike]

@@valeriumoscalu7580 Hey I just had that same code come on my display and truck shut on me everything seems normal but it won't crank or start when you turn key over. How much was the ecm if you don't mind me asking?

[@valeriumoscalu7580]

Around 700 for ecm and 270 programing

[@270lilmike]

@@valeriumoscalu7580 thanks

[@bereketsaid470]

i need power & GND input

[@shaznmohamed5266]

I need volvo engine control unit

[@user-zx8xh5rs8d]

Добрый день. Говори по русски с англ. субтитрами.

[@Volvomacktruckausterlia]

Engine programming missing 😂😂

[@musamusa6677]

Рашен акцент

[@valerianilichlomtadze6216]

Я грузин ... рашен акцент!😁

[@geoeconomics5629]

Cat 6NZ28895 all day long all year long

[@valeriimoscalu8794]

Волво центр