valve settings short method tractors&marine MECHANIC

[@rhodellucero6650]

salamat sa mga tutorial mo sir God bless

[@robinsonaroca6920]

Hola amigo cual es el torque de culata para este motor

[@ervinsafra]

salamat sa lesson boss, pwede po ba next time 4 cylinders naman na kubota ang gawan mo ng video ng pag timing? God bless po.

[@tractorsmarinemechanic]

Npakarami n po kc na po kc Ang gumawa non sa KZbin.pero cge sir...gagawan kita para sayo.subscribe k lng para maupdate ka kapag nakagawa ako ng four cylinder.

[@ervinsafra]

@@tractorsmarinemechanic salamat po sir, nakapag subscribe na po ako.

[@Psilocybinsvamp]

Did you not forgot the o-ring? 😬

[@mechanicjojo7383]

Boss TAGAL na Po akong subscriber Sayo mellenial mechanic pwd ba magsimula na akong mag vlog sa pag memikaniko kaw Po master ko hahahaha God bless po

[@tractorsmarinemechanic]

Cge malaya k magvlog. wag mo lng copyahin ung mga video ko kc makacopy right k.at salamat for subscribing.

[@mechanicjojo7383]

Yung turo mo lng kokopyahin ko pero Yung video Hindi Po..

[@dotsie1978]

Thanks for this. I have that engine. Although I don’t understand the language you are speaking. It’s probably too much work for you to add subtitles in English to it?

[@tractorsmarinemechanic]

I'm sorry if you do not understand my language but if you want to watch in my playlist.i have another one video which is a long method tune up for a 3 cylinder engine.

[@tractorsmarinemechanic]

To understand that video just remember if you rotate your engine going to the right.there are always two valve must be open then apply valve setting on the remaining valves.the same procedure rotate again your engine...again,two valves should be open and the rest engine valves apply for valve tappet clearance or tune up.that is a short method.

[@kelanifellizar5419]

Boss my toturial vidio ka ba ng oberhauling cobuta

[@tractorsmarinemechanic]

Pakinood po nito sir sa ibaba, top overhaul lng po at Hindi pa ako makagawa ng video. kzbin.info/www/bejne/iGfZoWmCfM6ondE

[@hrfch3352]

Cual es el orden de encendido del motor 3 cilindro yanmar

[@tractorsmarinemechanic]

132 thank you for watching.

[@hrfch3352]

@@tractorsmarinemechanic muchas gracias

[@CandidoCaranto]

Boss pano mag adjust ng valve clearance gamit ang firing order

[@pabloferrari5324]

Hola tengo un tractor iseki necesito saber cuánto kilos de torque le dan a la tapa de cilindro

[@tractorsmarinemechanic]

58 lbs

[@allanducado5251]

Boss ano firing order kapag 3cylender kubota l3608

[@tractorsmarinemechanic]

Salamat sa panunuod sir.alam.ko po lahat ng Kubota na 3 cylinder ay 123 Ang firing order.sir baka pwd follow mo rin ako sa fb page ko.tractos and marine mechanic din po Ang hanapin nyo.salamat

[@boyraon3566]

God eve Po San Po pwd mkabele 3 cylinder n mkna

[@dudongdmc3595]

Boss tutorial din sa 2 cylinder salamat boss

[@tractorsmarinemechanic]

Sir,pindutin mo ung playlist mo at Makita mo or mapanood mo don meron npo ako video Nyan.

[@dudongdmc3595]

@@tractorsmarinemechanic ah okay salamat po sir

[@camilogalleguillos370]

Como saber si exiten pistones de 82 mm de diametro ya que los que encsrge son de 83 mm consita puede haber una solucion es para un trctor kubota motor D1463

[@tractorsmarinemechanic]

I'm sorry I can't understand

[@ErwinBautista-w8r]

Ano po valve clearance po ng l2201 kubota

[@redentv4839]

Boss anu sira hindi lumabas ang langis sa may rocker arm hindi naman baradu malakas naman ang bomba ng langis abut 40psi ganyan dn makina 3cylinder yanmar

[@tractorsmarinemechanic]

Dapat po alam natin model ng makina sir

[@FortunatoArce-bi4lt]

saan ang adjustment ang krudo medyo maaksaya sa krudo sir tnx.

[@tractorsmarinemechanic]

Baka sira na sir Ang plunger.

[@FortunatoArce-bi4lt]

tnx sir

[@jay-arates3931]

Hello po sir,,,paturo naman po Kung anu Ang valve clearance ng d850 Kubota,,,salamat

[@tractorsmarinemechanic]

May feeler gauge kb? Sa feeler gauge mo pwd 0.25.

[@jay-arates3931]

0.25 inches po ba or mm sir?,,,tsaka sa intake at exhaust na po ba Ang ganyan sukat?

[@tractorsmarinemechanic]

Intake,exhaust at 0.25mm

[@jay-arates3931]

Salamat po sir,,, Godbless...

[@kubotad]

@@tractorsmarinemechanic sir ano pala valve clearance ng kubota d1462-di engine

[@gabrielcarvalho7593]

Motor de dois cilindros z402 Kubota por favor digam-me as medidas de válvulas regulagem obrigado

[@tractorsmarinemechanic]

025mm please also watch this from my playlist kzbin.info/www/bejne/pWWqdJ2gp9t3ntk

[@gabrielcarvalho7593]

@@tractorsmarinemechanic obrigado grande abraço daqui de Portugal

[@hectorchavez3583]

Héctor Chávez Vega motor John Deere 3 cilindro el tiempo del motor i encendido gracias Dios bendiga ecuador

[@tractorsmarinemechanic]

Thank you for watching

[@ahmedzxc8318]

ياريت ترجمه بي اللغه العربيه