Hey bud, I’m a 40 year old dude who is really just in the last year getting into all things mechanic fixing and upgrading. I just wanted to let you know I’ve subscribed, and liked many of your vids. But more so I think it’s impressive how much you know already to Be so young! Impressive. About to do these very things on this vid to my kid’s buggy and I wanted to thank you for making such detailed Vids available! This is such a resource. Thank you buddy!!
@jamesbeason92563 жыл бұрын
The aircleaner is something that bigger is not always better. Air velocity has to be taken into consideration. You could use a 3inch flanged airfilter, but you need to start stepping down the Inside Diameter of the airintake immediately. You can probably neck it down to 25% larger than the carburetor airhorn (air intake side) and still maintain air velocity to operate the engine. You may be able to get more velocity by putting the fliter inside of an airscoop facing forward. Air does not like 90° right angles. It hits 'the wall' in the 90° bend and tumbles. That's not what we want. We want the air to be traveling as straight as possible when it enters the carburetor airhorn. You can use a 90° bend, but you have to have sufficient velocity and the 90° bend as far from the airhorn as possible, right at the filter, to get the tumbling straightER as it enters the carburetor. A flexible accordion hose used for RV septic tank is a standard 2.5 inches and comes in 10 feet length. Use it for no 90° bends. A flexible straight 2.5 inch hose is even better. PVC can be used and make your tirns with the hose or use 22° or 45° PVC or radiused Turbo silicone connectors. Use 3- 4 inches of 2.5inch PVC pipe and connect a Spectre or K&N with a 2.5 inch flanged filter. Spectre can be used with no filter oil. I recommended a pre-filter for K&N. High flow comes at filtration cost. You can step the ID of the RV hose down with 1 or 2 PVC adapters to get it to your carb or TBI Outside Diameter. Use a piece of old bicycle innertube for a connection. Both K&N and Spectre make silicone sleeves to step down from 4 inch in .500 inch increments to 2.5 inches. If you use the above ideas, avoid 90° bends and keep velocity in mind any engine will run better with a good air intake system.
@tonzapower3 жыл бұрын
That's great advice James. I'm just about to do this on my buggy so will try and do it as you've described.
@bboyztv51225 жыл бұрын
Your neighbours must love you
@mixonmachines5 жыл бұрын
👍👍 love the muffler. Can’t wait to use it on one of my projects
@VasilyBuilds5 жыл бұрын
Definitely a nice muffler. They have 5 different styles and the carbon fiber one looks best IMO. I believe they cost 39$ from china. Only problem is the Outside diameter is way to big for most pipes, so there will be a gap when welding.
@melted_pistons5 жыл бұрын
Take the restrictor out of the muffler
@strubbleler3 жыл бұрын
i know this is from way back, but the bigger intake could work if you, when the engine is warmed up, fiddle around with the air screw, that is located on the side of the carb ;)
@culicheqwerty9355 жыл бұрын
that buggy sounds good
@justinm.35945 жыл бұрын
😂 Exhaust Fell Off... nice welds 😂 glad you got it fixed 👍🏼
@DragoWerx5 жыл бұрын
That sounds nice! Found your channel from a comment you left on "John Wheels", wish I would have found it sooner since I was trying to decide between the RLV muffler or a motorcycle style muffler. Got the RLV in the garage waiting to go on... nice channel, subscribed!
@brads11005 жыл бұрын
Take the tire and tube off and make a new center out of say 1/4 or 3/16" plate. Then keep your eyes on CL for new wheels.
@VasilyBuilds5 жыл бұрын
Me and my dad actually cut out a center for the rear wheel after it fell apart too, and it was a complete pain in the but to cut it out. The welding part was easy though. If it happens again, I'm going to the machine shop. But these are the wheels and tires I'm looking at for the power levels I will be running next year rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F332760438422
@cryptohippo60085 жыл бұрын
Awesome!! Gunner at the rev is hilarious 😂 sounds great with the new exhaust tho! Just slap some duck tape on the wheels, I wanna see some offroadin rite nie! 😁
@VasilyBuilds5 жыл бұрын
Alright!! Ill see if i can find a trailer wheel with the same bolt pattern..
@cryptohippo60085 жыл бұрын
That would work!
@JohnWheels5 жыл бұрын
Great video! I really think some bigger intake pipe would help though! The muffler sounds awesome!
@VasilyBuilds5 жыл бұрын
Thanks John! I wanna try those
@boisebadboy933 жыл бұрын
Is the rear axle wheel spacing stock? Alot of the chinese karts have the back wheels so close together. Drives me crazy
@jamesbeason92563 жыл бұрын
Use 10gram roller weights. They're good for getting torque to the ground. 8grams make them climb like goats, but take topend off.
@megadawg3422 жыл бұрын
I prefer sliders to weights, they perform a little better.
@66mybeat5 жыл бұрын
That exhaust turned out awesome! Nice work!! Buggy sounds great.
@VasilyBuilds5 жыл бұрын
Thank you sir!!
@rhys76715 жыл бұрын
Also would be cool to weld some jerry can holders on the side
@GoKartsorGoneFishin5 жыл бұрын
Another great video!👍
@VasilyBuilds5 жыл бұрын
Thank you !!
@culicheqwerty9355 жыл бұрын
i like your buggy and HAYABUSA Exhaust
@stevehamby41633 жыл бұрын
I've got a fang dong 169cc buggy. Its all factory , any advice on some mods?
@mello.-.65165 жыл бұрын
Great video I never seen the dune buggy :3
@VasilyBuilds5 жыл бұрын
Thanks!! I had made a video of it back in November 2017
@mello.-.65165 жыл бұрын
@@VasilyBuilds oh well I'll check it out :)
@MrBuckshot183 жыл бұрын
Where can you find wiring harness for these types of karts? Can you do video on how to wire?
@VasilyBuilds3 жыл бұрын
My least favorite thing to do lol
@JoseManuel-lj4dk5 жыл бұрын
Lol that's how I ride my go kart. A straight pipe and same engine.
@Darrenbrown095 жыл бұрын
Whats the model or name of this thing? Would like to try and find one around me. Thanks.
@gabrielq.9064 жыл бұрын
Is that the stock exhaust pipe? I want to mod my exhaust on my 150cc kandi but can't find a pipe for it. Everything I've found is for a scooter
@jamesbeason92563 жыл бұрын
BDX Performance $150
@Nitro914 жыл бұрын
What size tires and wheels are you running
@rhys76715 жыл бұрын
Get a pit bike foam air filter they alow a lot more air flow
@A_Stereotypical_Heretic2 жыл бұрын
1:35 look at that big steaming pile of dog poop on that tire lol
@am57185 жыл бұрын
Good work
@natelee52825 жыл бұрын
Nice editing
@VasilyBuilds5 жыл бұрын
Appreciate it bro!!
@Martyimgay3 жыл бұрын
Just wondering the 2 hoses that have vacuum which are the crankcase hose and the I would say valve cover hose at the very front what did you do with those hoses being you have a aftermarket filter cause those hoses went to the old air box.
@Martyimgay3 жыл бұрын
Just wondering the two hoses that I have left over after putting a aftermarket filter which are the crank case hose and I think valve cover hose at very front… they were both connected to old the airbox I have a 169cc “150cc” go kart
@roostertailmax69425 жыл бұрын
Nice vids and buggy👍
@VasilyBuilds5 жыл бұрын
Thank you!
@hippiedave_5 жыл бұрын
Killer dude
@jesusischrist1527Ай бұрын
I cant get my clutch and variator off of my 05 gy6 150cc crossfire , any suggestions ?
@stephaniehart82415 жыл бұрын
nice vid
@boisebadboy933 жыл бұрын
In case anyone was wondering. This is a BMS Sand Sniper 250. Also, if anyone has one of these, are they good quality? Reliable? Thoughts? I'm seriously considering one
@CorralesRacing5 жыл бұрын
Buen buggy 👍suena que parece una metralleta jejjejej
@FangOfTruth5 жыл бұрын
Running a liscense plate not registered to vehicle is illegal.Better off with no liscense plate.
@H4HDJD5 жыл бұрын
Vasily Custom Builds but I would say it probably stands out more because of the license plate so I would take it off
@JetSkiBuyFixPlaySellChannel5 жыл бұрын
Just asking for a big ticket if you leave it on.
@reggiexp695 жыл бұрын
i mean you wouldnt be pull over that fast cause of the licence plate. i did run my licence plat of my other quad on a other quad i had cause one wasnt registered. so it would look less suspisious
@snapfish895 жыл бұрын
Looks like a 50$ China exhaust from the wsh/geek app.
@VasilyBuilds5 жыл бұрын
Sorta, it was a 39$ china exhaust from ebay
@JonLinton_3 жыл бұрын
What’s the top speed on this?
@elcreador66755 жыл бұрын
Excelente 🇩🇴🇩🇴🌎
@FreakinKatGaming4 жыл бұрын
ill never forget the 1st time my dumb ass tried welding and i looked at the FUCKING ARCH!!!! 3TIMES!!!! just a peek, a tiny glance to make sure i was in the right spot, MY EYES WERE ON FIRE THE NEXT MORNING! so when someone says dont look at the arch... DONT! then i see the camera angle and an arch nightmares come back to life. the horror
@TheInfamousDy4 жыл бұрын
What exactly did u do to the rollers? Just take 3 out and leave the others in?
@VasilyBuilds4 жыл бұрын
yes correct
@TheInfamousDy4 жыл бұрын
@vasily thanks bro
@A_Stereotypical_Heretic2 жыл бұрын
I hope by now you learned how much that air intake hurt your performance. Always gotta think of air like you would water...and the path of least resistance.
@howiseverybodybeinggonesof23285 жыл бұрын
Kelly Davis in Macon GA 🍂🌵☘️
@Amy-wh3dt5 жыл бұрын
It looks good an sounds good
@NewfoundlandBen7095 жыл бұрын
Nice work, may i have a link to buy the exhaust
@VasilyBuilds5 жыл бұрын
Thank you !! www.ebay.com/itm/New-Exhaust-Muffler-DB-Killer-Pipe-Slip-On-Off-Road-Motorcycle-Dirt-Pit-Bike-ATV/232235811164?hash=item361255415c:g:kiYAAOSwPIhaAUoo:rk:6:pf:0
@vibinmonuttan50416 ай бұрын
What is the HP@rpm and NM torque @rpm ??
@4486xxdawson5 жыл бұрын
At 1 40 you can see dog shit on the left back wheel , man i hate that , working on it and trying to figure out whats that smell lol
@coltonbaird70375 жыл бұрын
Dude you really need to put them weights back In you’ve gotta rev the crap out of the engine to make it move now
@VasilyBuilds5 жыл бұрын
Its not bad. I am going to try to order some waits lol and tune it.
@coltonbaird70375 жыл бұрын
O ok I guess It just looked like that on camera
@mrgmc63145 жыл бұрын
Cool cart but needs a gsxr 600 motor
@shanerogers2835 Жыл бұрын
This video was posted 4 years ago. IDK what state you live in, but in Texas the police would confiscate your go kart, or anything you have that has a license plate that doesn't belong on the vehicle, trailer.
@crazycreation69924 жыл бұрын
Is that a two stroke engine
@jasonjulian14 жыл бұрын
No, the 150cc gy6 is a four stroke single cylinder cvt scooter engine. I have one in my quad. Hauls ass pretty good so long as the vehicle and rider weights don't get nuts.
@Aaron-nl7iu5 жыл бұрын
Hey bud, what is that buggy called? I just got the same one and I dont know anything about it. It's a 150cc right? What's the name of the buggy called? Any help would be greatly appreciated:)
@VasilyBuilds5 жыл бұрын
Made by bms. Sand viper 150. Air cooled 8.5hp gy6 150cc with reverse
@HypebeastMajorities5 жыл бұрын
😃😃
@juancarlosruiz19855 жыл бұрын
What is the brand of that gokart?
@VasilyBuilds5 жыл бұрын
BMS sand viper 150
@pitbikemadness19415 жыл бұрын
How many times do you get the cops called on you
@pitbikemadness19415 жыл бұрын
Damn when I had my motorized bike running I would be the cops called all the time and I ran from them on a 40mph riding mower
@VasilyBuilds5 жыл бұрын
My neighbors are understanding
@theworldoverheavan5605 жыл бұрын
@@pitbikemadness1941 lol
@custombikes75245 жыл бұрын
U should get it street legal
@carlosperez473cp3 жыл бұрын
Lol where you from? I'm in fresno
@MrCATHALM33455 жыл бұрын
I have a HAYABUSA engine is a small pick up truck i have a short 0-100 mph video on it.
@nickdavis15575 жыл бұрын
Can I get a shout out on the next video, I'm in Memphis!
@smoking-tm9xh5 жыл бұрын
the exhaust have db killer!!remove...
@VasilyBuilds5 жыл бұрын
Yes it is very loud, so i left it in
@tstricklin8535 жыл бұрын
✋👏👍
@austinback54355 жыл бұрын
Keep the license plate
@boya3goob2185 жыл бұрын
Please go to eBay and find a 600 or a 1000.
@mello.-.65165 жыл бұрын
Ha first
@BeaSTly_Kiila5 жыл бұрын
2
@driveitbreakitfixit74965 жыл бұрын
Il sell my buggy to you
@VasilyBuilds5 жыл бұрын
I might consider it
@Realryancurry5 жыл бұрын
Get that junk engine out of there and put in the kx250
@VasilyBuilds5 жыл бұрын
kx250 is reserved for my new build. Might do a vtwin in the future