Land Rover Discovery 3 - Wrong type of brake light bulbs causing faults?

[@wellanhouse]

Hi Cristian, many thanks for all the video's. As an ex Discovery 3 owner I had so many problems including the "3 Amigo's". The 3 Amigo's is caused by a CAN bus crash where none of the computers can communicate. There have been many causes given, but one I have experienced is bad electrical connections in unrelated circuits causing maybe slight arcing and electrical noise that interferes with the CAN bus and causes a computer error that it seems the system cannot recover from. I have found a bad brake pedal switch causes this and I can also imagine a poor connection on the bulb could also. This may be the source of the rumours about bulbs. I also had the 3 Amigo's from a bad high pressure fuel sensor - I think it just confused the ECU. I have heard from engineers that the type of CAN bus used in the Discovery 3 is not really suitable for the number of computers. Keep up the good work, and I hope this helps. Steve.

[@avozdageracaode816]

Even not owning one, I still love watching these vids.

[@Vera_and_Christian]

Thanks for watching 😃👍🙋‍♀️ Vera

[@toddhoffmaster6057]

I feel the same way. I own a Jeep JK Rubicon, Christian and Vera are such a joy to watch that I can not get enough of their videos. :)

[@hansdenotter7376]

Christian and Vera, these videos are highly appreciated. It’s because of the clear and straight analytical capabilities and work ethics of you both. Thanks!

[@davidedwards4125]

Hi, from personal experience this is a problem. My D3 started throwing lots of issues on the matrix display and went into limp mode. I limped home after a code read from my friendly garage (LOTS of codes). Got home and remembered that bulubs can be an issue, checked and one was blown, replaced it and it was fixed and been so for three years so its not a loom issue etc. I dont think cheap incandescent bulbs can be an issue, unless they blow, but cheap LED will as they dont have ballad resistors. Just like they mess up trailer relays. The other thing is the brake switch, this causes the same issue when it starts to fail. I always carry spare bulbs in my Disco due to this and usually prefer the decent branded ones, maybe one-day ill do a proper LED conversion. PS that was a lovely digram you drew.

[@Vera_and_Christian]

Sounds absolutely plausible what you wrote. Thanks 👍

[@algprt]

Hi again Christian, great video as always. Some quick remarks: (1) true, HDC activates the break lights, you can notice that on a hill descent during the night (LR break light are powerful) you will notice the red color behind. (your Freelander does that too 😉 mine did) (2) the "sensing" part of the control module can sense changes in the current/voltage, outside the specs; for example if your bulb is gone when you press the pedal, it will "know" because there is an abrupt change. It then throws an error (3-amigos...), ignition off, then on again and error is gone (but bulb is gone too 😞) Same can happen if you install cheap LED (because the power consumption is "too low" (wrong resistor values)) the module will think you have an open circuit or burned lights. 😉 (3) same error can happen if you have a break switch fault (sudden change in voltage or current sensed by the module). A quick note, I converted all my interior lights to LED... I can assure you... cheap one will fail quick because there is no voltage control for these lights, they will burn soon due to the high peaks of voltage (specially in the rear/booth interior light) if the light itself cannot endure the surge. (old filament bulbs are much more resilient in that sense)

[@Vera_and_Christian]

I will pay attention to the HDC brake light next time in the dark. Who thought of this trick? Thanks. Reg (2): the ecu is in parallel connected to the bulbs, so the voltage/current is independent of the bulbs - as long as there is any bulb installed. No bulb or open circuit can be detected by the ecu and it triggers a brake switch sync fault. Cheap LEDs are usually a waste of money. I learned that too. Thanks.

[@djaxclips]

So does this mean a faulty rely for the HDC can cause the three amigos?

[@rangie944]

Been worried for days about Vera's pen, she obviously relented and allowed you to keep it. Christian, great video, enjoy this technical aspect. Thanks for posting.

[@Vera_and_Christian]

😅👍🙋‍♀️ Vera

[@rrshse6704]

Great presentation once again Christian. Never had an issue with the brake lights in my Range Rover in almost 15 years. I think I changed the bulb on the left signal once and also the side markers a couple of times. Cheers from Canada! :)

[@The-Observer]

Very interesting video. I have a brake light issue that crops up every year, same bulb all the time. Tried cheap and expensive bulbs and it's still there. Thank you for my sticker too, it arrived this morning. I think I know where it will go but will email you a pic when I've done it :)

[@DiscoGruffalo]

The light bulb problem occurs when 1 filament in the twin filament (stop/tail) bulb breaks in a particular way and touches the other circuit inside the bulb. This is what upsets the electronics due to some feedback problem going to the ABS unit.

[@AJB1]

I wonder if it sees voltage coming into the ABS unit from the send to the bulbs (that extra wire on the circuit going from the bulbs to the ECU), and uses that to detect a brake light switch fault. If the brake lights are on, but it hasn't been told that the brake pedal is pressed, and it hasn't activated the HDC brake light relay, maybe it assumes that the half of the brake light switch feeding it must have failed, and goes into fault mode? Twin filament bulbs could feed power from the tail lights into the brake lights if there's a bad earth connection, as the tail light on one side can't get to earth, so goes back through the brake light filament on that side, across the car, then to earth through the other brake light.

[@AllenManor]

Sewing is sadly a dying art! I am impressed with how industrious you both are. In this way a Land Rover is the perfect car for Germans as it always gives you something to do! A Toyota or Honda would be far too reliable and boring as a result. Thanks for the video.

[@Vera_and_Christian]

😃Thanks 👍🙋‍♀️ Vera

[@Willard05]

I was thinking about trading in my discovery 3 for something else and my wife said "but you kind of like the troubleshooting"!

[@AllenManor]

@@Willard05 Every time I watch an LR Time video I breathe a sigh of relief that I did not buy a Discovery 3! Great car but I don't have the time/money/engineering skills that Christian possesses to keep it running right.

[@josephp5058]

Very informative Christian good to know just a bulb causing the usual heart stopping LR 3 owners dash display faults - I upgraded my rear lights sets to Disc 4 purely for vanity reasons as the old lights looked a bit dated I thought - love to Vera

[@petery3523]

Thanks for all the effort put in to make your videos, greatly appreciated both for information and entertainment 👍

[@Vera_and_Christian]

😃 you're welcome 👍🙋‍♀️ Vera

[@AlexStrugariu]

Haven't watched the video yet, but I can relate from personal experie ce that Yes! I had two burned brake light bulbs, and that caused Xmas tree on dash, suspension lowered to bump stops, no speedometer, no odometer. Replaced bulbs and all was good :)

[@AlexStrugariu]

Continuing watching the video. I always use generic dual filament brake light bulbs.

[@Vera_and_Christian]

We had that problem on my Freelander, it was not the bulb, but a corroded ground wire. Had to take almost the entire car apart to find it 😂👍🙋‍♀️ Vera

[@davidedwards4125]

Yes, me too. Had lots and lots of codes, limp mode etc. Limped home and remembered a post on Disco 3. Checked bulb, blown, replaced. Car fixed instantly. Its NOT the harness, its odd voltages in the CAN BUS allegedly.

[@briang1561]

I love your schematic drawing!

[@wammdriver]

I brought a Mitsubishi Pajero years ago that had an ongoing ABS light problem, the owner had spent a fortune st Mitsubishi on abs sensors, rings and diagnostic work, they then condemned the abs unit itself and wanted £3200 to replace it. I bought the car and driving behind it one night noticed the high level brake ligjt glowing slightly when the lights were switched on. Also when using a trailer the ABS light would go out. Turned out to be the brake light bulb, it was a stop & tail and inside the two small arms of the filament were touching causing voltage from the lights to be back fed into the brake system, £0.50 for a new bulb saved £3200

[@robgreenhill1426]

Hi guys. Got my sticker this morning and it is now proudly on the tailgate. It’s already getting attention

[@Vera_and_Christian]

Can you email a picture, would love to see it 🙋‍♀️ Vera

[@robgreenhill1426]

@@Vera_and_Christian yes of course

[@Nigel-nar53]

Great schematic takes me back to my working days. Custom Disco bags too, can't be bad. 👍

[@danhayes3546]

Hi yes the brake lights do come on with hill descent activated great video

[@eildonweir9693]

Well done to Robin. I’m an old retired Aussie, I started out as a boilermaker in the 1970’s. watching his enthusiasm while using the hand wheel bender was a pleasure. I am confident he will develop into a very skilled craftsman. P. S. Travelled to Darmstadt while working for a German company (Schenck Process), for many years. Great memories.

[@Vera_and_Christian]

Christian's brother worked at Schenck Process, Christian himself works also at Schenck, but not at Process. 😃👍🙋‍♀️

[@eildonweir9693]

@@Vera_and_Christian Small world hey, I travelled there from 2012 to 2019. But still keep in contact with old colleagues. If he recalls an Aussie (Dick Armstrong), say Hi.🖐

[@johnbowling6618]

Great video (as usual), Christian, you need a "It's LR Time" sticker on your new cable bag that Vera made. 😉

[@Vera_and_Christian]

Great Idea, I am going to put one on. Maybe I'll get patches one day, then I am going to saw them on. 👍🙋‍♀️ Vera

[@daz.j]

swapped mine out for d4 tail lights they look much better and are leds so no worries about them going out

[@davidmscott4409]

Finally someone made this video! The discovery 1 won’t go out of park with the wrong bulbs! My LR3 acts wild.

[@Vera_and_Christian]

😂😅👍🙋‍♀️ Vera

[@ONELIFELIVEITOZ]

I ended up putting good quality LED bulbs in. In saying that I did put in some cheap eBay led bulbs in and instantly got the 3 amigos transmission fault. Swapped back the good quality LED bulbs, problems solved after code cleared.PS great videos you guys.

[@MrSidestick72]

Interesting log, but from what i know the car is able to compare the resistance of bulbs within a range of value. From workshop manual: The CJB monitors the status of the lighting circuits, relays and switches. If a fault occurs, the CJB stores a fault code applicable to the specific fault which can be retrieved using T4 or other suitable scan tool. You can check it also on the "control diagram" of Exterior Lighting section (417-07) of workshop manual.

[@grahamlewis3387]

Great video Christian, Vera's bag what a great job!

[@Vera_and_Christian]

Thank you 👍😃🙋‍♀️ Vera

[@__FJ__]

I don't know if I'm alone in this, but I would definitely watch a LR bag sewing video.

[@Vera_and_Christian]

Cool, thanks, maybe we'll do one 😃👍🙋‍♀️ Vera

[@rafallubniewicz3696]

As always, a good movie. Christian you are a real Mythbuster. Thank you for the sticker. It sits in the right place on my LR3. Regards.

[@TheDefender1968]

Hello. I liked the explanation of the lights, but good good, it's the bag 😎. Congratulations Vera. A hug from Portugal.

[@Vera_and_Christian]

😃🙏👍Thank you and thank you for your picture 🙋‍♀️ Vera

[@robpeabo509]

I got tired of replacing rear brake and reverse light bulbs. It happens way too often. Today I bought Narva LED replacement bulbs. They look good, the combination Stop/tail LED bulbs are marketed as Stop/Tail. They are not ridiculously bright like some LED's are. The single filament replacement LED for the reverse light and the other rear tail light are great also. Both tail lights on each side are the same brightness. I have never had an issue with indicator bulbs and the rear fog lights, so I left them as incandescent bulbs. I am hoping that as Narva are a reputable manufacturer, and that LED's are more tolerant to voltage variations, the LED's will last the life of the vehicle. They come with a three year warranty. I am a receipt horder, I will be claiming them under warranty if they fail under three years!

[@1me1ie1]

I have received my LR Time sticker 👍😁 Thank you very much 😎

[@RickActual]

Christian, Those nuts. What a legend.

[@bane8593]

Hi two in a week yay. I can confirm that HDC dose put break lights on.

[@Vera_and_Christian]

Thanks, I don't know why we didn't do that ourselves. We even live on a steep hill. 😃👍🙋‍♀️ Vera

[@joshjay6058]

If you put a single filament bulb in a double spot or vis verse you can cause a HDC fault. Type matters not brand. I see it all the time in the shop. And when the taillight harness goes bad it will cause the running/brake lamps to do act funny and this too with cause HDC/Suspension faults. But you are correct you don’t have to buy bulbs from land rovers dealerships. Cheers! Funny story I actually had a truck get towed in cause it wouldn’t shift passed third gear. Had no faults what so ever. But it would shift it your manually commanded it too. Guess what caused it! Customer installed the wrong size bulb!!! Crazy stuff!

[@clivewasson1660]

Hi I enjoy your videos and watched this with interest a few months ago. I had a brake light issue this week. (Changed servo didn't adjust brake light switch ,so brake lights always on) This caused a HDC error followed by car lowering. Switch car off and on again error cleared. So if brake lights not on same circuit why did the lights on cause a suspension error? Keep up the good work I enjoy them regularly.

[@Vera_and_Christian]

Almost any fault will cause the LR3 to go in limp mode. The ECUs are connected to each other over a Bus. This is one of the biggest downsides of this vehicle. Christian

[@pwatom22]

Those do look like great bags.. Way to go Vera.

[@Vera_and_Christian]

😊😃👍🙋‍♀️ Vera

[@merseybeat1963]

Christian..We have an 2006 LR3SE V8 4.4 now with 207,000 miles and have had it since 23,000 miles bought as a certified car in 2008. Some years ago all of a sudden we leave our house and a block away pull over as we realize the car (which is Automatic) is not shifting out of 1st Gear. Worried that we are in a big problem. I get on to the Land Rover Forum in LR3 section and one guy says in response to someone having the same problem ..check your tire pressures and your rear brake lights..It can be caused from wrong light bulb and uneven tire pressures. I checked and rear left brake light bulb not working and front passenger tire was very off. We borrowed a car from friend and bought the light bulb from dealer..adjusted air in tire..and car began shifting normal. The stupid careless place we were taking car to put the wrong bulb in. (I say stupid because we almost blew our engine due to they're carelessness and our beloved cat died from the coolant due to them) Since then it has happened again to us again a couple of times and we learned that if we switch it to Manual she can drive it until we can get our OEM bulb..as once we bought the AutoZone recommended ones and it did not solve issue. Don't ask me why. Since then we have learned when this happens it actually WILL shift in automatic if the front headlights are in the off position. Im not lying. This is a quirky situation.The last time this happened I just said to my wife pull over probably the light bulb and there it was so she drove with headlights in the off position and ordered bulbs from dealer. In our case it is almost always the drivers side rear. A few days ago our dash showed faults..on Forum they said maybe rear bulb or battery. Our mechanic ordered us the best Interstate AGM battery ...also rear brake light not as bright as right.. so he scraped socket put new bulb in all dash lights clear. Cheers

[@mickbawn6815]

Very thorough as always,thanks

[@ShalevJonathan]

I afraid you missed the issue. The ABS module is getting 2 inputs from the brake paddle switch (one is normally open and the other is normally closed). The N.O. one is also responsible for the brake light. If the bulb you are using has a lower resistance than normal it might cause the voltage on this branch to drop. The result is that the ABS module is getting an “illegal” low on both inputs.

[@mustyguld]

🤔You have assumed that what was designed what is implemented. Perhaps there is cable manufacturing issue or its software related but we had it 2 times. In each I had to replace the right bulb and things go back to normal. Anyways it’s always fun to watch you mad scientists.

[@Vera_and_Christian]

😂👍🙋‍♀️ Vera

[@sergebuziuski6753]

It's correct if you look at the bulb with 1 filament. In our case we have double filament bulbs. Try to see what will happen if lets say Brake light filament brakes from 1 post and lays down on tail lamp filament - short. You turn lamps ON and your ABS module would sense brake lights ON.

[@Vera_and_Christian]

Sounds plausible what you say. This is a scenario what would potentially cause a ecu fault. But this could happen with any bulb. I claim that „LR bulbs“ are no different from others. Thanks!

[@simonfletcher545]

Hi there Christian and Vera. I love your channel, it always make me laugh as well as being informative. How did get into Land Rovers? What made you into enthusiast?

[@Vera_and_Christian]

When we bought our fixer upper house, we needed a workhorse. And a Freelander seemed like the perfect addition to our little project back then. That's how it startet.🙋‍♀️ Vera

[@gcmr87]

Thumbs up for the drawing

[@be4tnl]

Christian, what is your profession? you have so much knowledge of so many different things

[@TheDaf95xf]

Christian your a funny guy with your misses lol 😆 😎🏴󠁧󠁢󠁥󠁮󠁧󠁿

[@youserious6725]

I had my Disco 3 go into limp mode when i had 2 broken tail light bulbs. During day everything fine, at night it went into limp mode. Easy when you know frustrating trying to find the issue

[@selebalotsiu7139]

😢I was made to believe the wrong bulb will cause dash faults... Ouch. I once experienced but how it disappeared I dont know. The main changes made on my vehicle we brake switch and drainage pipes replacement later on

[@nutrunner5442]

Hi guys another great presented video as always so informative can I put in an order for a couple of those nice bags I have use for them in my discovery 3 also 👍👍

[@Vera_and_Christian]

😃Thanks, great idea with the bags, never thought that someone else might like them. 👍🙋‍♀️ Vera

[@Rickwardful]

I had recently a problem with my automatic Discovery 3 that was definitely a rear tail/Brake light connection problem. The vehicle would intermittently not change up gear in Auto, but would do if I shifted to Manual +/- mode. Eventually I discovered that it work fine until I put the side/main lights on. Turn the lights off and it was fine again. I had already changed the Brake light switch, but this made no difference. Once I had checked the rear lights, this is what they showed: Pressing the brake pedal did not illuminate any Brake lights, either the LH and RH or the Upper central LED’s There are in fact 4 rear side/main tail lights. 2 RH and 2 LH. Each on top of each other. Switching them on, only the upper of the RH and LH side /main lights came on, PLUS the Upper central LED! Question: Why is the Upper central LED on when the side/main rear lights are on? It turned out that there was a fault with the upper LH side main light. The Brake light filament of that bulb was blown and possibly the contact (bulb to socket) connection was not good. Simply changing that bulb, made both RH and LH side/main lights illuminate, WITHOUT the Upper central LED. When the brake pedal is now pressed, both upper side/main lights show a brighter light AND the Upper central LED works, as it should. Now, the Auto gearbox changes both up and down gear as normal, again. But who would have thought that this Automatic up-change gear problem would have been caused , JUST by a blown Brake light bulb/ bad connection?

[@nameless90210]

Same issue happened to me on 18yo D3. Auto gear box stayed in lows but manually could be pushed up. Also suspension lowered, HDC fault indicated etc. Service changed broken brake light bulb and voila all good now.

[@andicog]

Remember when you could just replace a bulb? I had a Ford galaxy, replaced one brake bulb, and then the other one went, dealer said Ford bulbs have a resistor?. Also had a vauxhall Astra that when one dip beam bulb was replaced the other would go a week later, had to be replaced as a pair apparently. Crazy.

[@Vera_and_Christian]

😅👍🙋‍♀️ Vera

[@dancosburn972]

The hill decent control dose turn on the brake light. Confirmed.

[@stevenbell7902]

When I had this problem it turned out to a build up of greasy muck on the brake pedal switch. It was diagnosed while driving in convoy and talking on the radio to the driver following me that the fault occurred when I used the brakes. Turning the ignition off then on again reset it until I braked again. The brake light came on, the suspension dropped and there was a lack of power. I took the switch apart and cleaned the contacts. It has not been a problem since then.

[@Vera_and_Christian]

👍😀In my Freelander, people come to my door at a red light in the dark and tell me what lightbulb is broken, freaks my out every time 😄.🙋‍♀️ Vera

[@trevorelgram2108]

Hi thanks I thought the brake light bulb was my problem now im told its the switch under the footbrake,can you advise

[@Vera_and_Christian]

You need to get a diagnostic tool and find out for yourself Read out the error message. If it's the brakelight switch, then you can change it easily. We have a video of course kzbin.info/www/bejne/nqCWpnmoaMqFh7M🙋‍♀Vera

[@thomassand7520]

We love Vera 🇩🇰🇩🇰

[@Vera_and_Christian]

😊😅👍🙏🙋‍♀️ Vera

[@peterbullen3347]

There is also an issue with trailer lights being LED, I had to fit a resistance load to allow the indicators /turn signal to work

[@Vera_and_Christian]

The trailer lights were flashing like a Christmas Tree when hitched to my Freelander. It was caused by a corroded ground cable on the car. It took us forever to strip the car down to its metal and locate the right ground connect. Maybe we filmed it 🤔. 🙋‍♀️ Vera

[@peterbullen3347]

It seems to be an issue with Landrover here, my brother has a RRS and same issue, but not on other European cars like VW,

[@DrB606]

Hi Christian, you are a funny, love your posts! The lights (even on a LR3 😁) are monitored by a light control module ECU using CANBUS wiring. It will throw the "bulb out"warning when a bulb draws no or not enough power. This happens the bulb does not match factory specs (power draw) or there is a ground wiring problem. I've seen people putting the "modern"LED replacement bulbs in with negative results. LED bulbs need to have the "CANBUS compatible" stamp in order to function properly on these cars.

[@Vera_and_Christian]

Thanks for the tip with the LED bulbs, 👍🙋‍♀️ Vera

[@SiCrewe]

Seems kind of odd that HDC requires a separate circuit to illuminate the brake-lights, given that HDC activates the brakes anyway. I guess the problem is that your brake lights, in reality, just signal that the brake pedal has been pressed (rather than signalling that the brakes are actually operating) so when something other than the brake pedal activates the brakes there needs to be a whole other system to illuminate the brake lights. Would probably have been simpler to have the brake lights activated by a pressure switch so they'd come on when you press the pedal OR when other systems activate the brakes without the need for separate circuits.

[@johnhammond9174]

Morning hope your both well doz LED light bubs make a difference and are thay better 🤔 John😁🇬🇧👍

[@SilverSiaram]

The "three Amigos" is quite common with the discovery 2... And is very annoying as there are multiple options that can cause it. I'm not sure you can use led light bulbs in the D3, I have a feeling it requires a high resistive load?

[@charlesdickinson7180]

Hi Christian and Vera Just want to say thank you. I received my sticker this morning. Just trying to decide now where to best display it on my Discovery. Where do you have your sticker on your lr3? Can’t see it anywhere on your videos. Try and point it out when you do your next one. I’ll send you an email with pictures once I’ve decided. Thanks again Charles

[@Vera_and_Christian]

I have mine on a side window in the back. 👍🙋‍♀️ Vera

[@charlesdickinson7180]

Thanks for replying Is that in the Freelander ? Where do you have the sticker in your LR3? Thanks Charles

[@Vera_and_Christian]

@@charlesdickinson7180 On the rear window upper left corner. Christian also put it on the fender, drivers side, close by the mirror. 🙋‍♀️ Vera

[@charlesdickinson7180]

Thanks I’ll look forward to your next video Charles

[@landrover3596]

Why not just convert to oem led taillights no more bulb changing. If you have a wiring problem that's a different story. I changed my taillights to the oem led from the LR4 , interior lights also to led and my foglights to bi-xenon bulbs. Also added bright white led daytime running lights.

[@peterbullen3347]

Hi all, I have had this error once, does anyone know if LED upgrades cause this? It happened when I was using HDC too

[@ian_s7481]

Where are the Vera sewing video’s? 🥺

[@Vera_and_Christian]

I hope to do one after our vacation. 🙋‍♀️ Vera

[@yairshemtov1406]

Hi I have a Discovery 3 2009 I replaced all the bulbs in the tail of the car for LED and after I turned on the lights I have lamps that came on in the dashboard. After I got the normal bulbs back it worked out. You can check it out yourself and broadcast it please. Thank you from Yair Shem-Tov from Israel

[@Joeysworld1]

Hey guys. What is the intro music please?

[@Vera_and_Christian]

Oh it's free, from theKZbin catalog

[@vedatguclu4678]

Meraba ben turkiyeden yaziyom siz bu aractan anliyosun benim bir sorunum var araci ben yeni aldim 2006sport aracta tv alt yapisi var ama ekranda tv menusu yok bunu kendim yapa bilirmiyim yardim edermisiniz

[@gordonbarclay6106]

Don't know if it was true or not was always told if you you drove a Volvo you couldn't use cheap bulbs as they were not suitable for the wiring. You had to put dealer bought ones in.

[@pdmark311]

I replace the brake lights with DOT approved LEDs.

[@OleSchjodtOsmo]

Great video as always :-). You can see the brake lights when using HDC in this video by Jay Tee, also commented on 3:25 in to the video. kzbin.info/www/bejne/fXPYnYd7l7ytj5o One of my brake bulbs "exploded" and strange things happened with all the lights in the rear. Changed with cheap bulbs, working perfect now.

[@johnnyclark4548]

😂😂yes you dont need the genuine globes, my experience is the body control module does have a influence and its always caused when only one globe is renewed and the problem does not happen instantly. My advice is yes buy the cheapest globes its fine but buy a 2 pack and renew both at the same time and problem solved. I have seen vehicles with cruise control problems and renewing the globes yes both fixed the problem.

[@drewbale]

V over I r omhe law ? Sowing make new seat covers with the lr logo

[@Vera_and_Christian]

Great idea 👍😃🙋‍♀️ Vera

[@danielettlin3093]

Leider die ganzen Videos nicht auf Deutsch 🤷🏼‍♂️

[@Vera_and_Christian]

Wir haben leider kaum Zuschauer aus Deutschland. Laut unserer Statistik noch nicht mal 1%. Unsere Videos sind sehr aufwendig, in der Reparatur, im Dreh und vorallem im Schnitt. Da gehen gerne 20 Stunden pro Video drauf. Da liegt uns doch sehr daran das wir so viele Zuschauer wie möglich ansprechen können. 👍🙋‍♀️