Vermeer Sc 252 stump cutter wheel upgrade.No money. 3pkts 6 teth. Pls lke and subscribe

[@whelanstradfallning5432]

Your videos on the sc252 are great, thank you and keep making them 👍🏻

[@RussToronto]

Thank u

[@RussToronto]

Thank you Eric

[@RussToronto]

Use any teeth and pockets you want the will all work

[@andrewwastien]

what pocket series and teeth are those? 1100 900? and what series should I chose for a sc362?..... I currently have 900 series on it 6 angled pockets and its not performing wheel I thought that the cutter wheel was not spinning at a good speed but I measured the rpm on it with a laser tool and it shows 3200 rpm's teeth where sharp too.

[@RussToronto]

I'm not sure I've just tried it on 252

[@RussToronto]

1100 are best

[@donpaulausky2348]

Hi Sir like your Videos huge fan i have a 252 vermeer & my chip shield bracket broke & cant Figured out how to fix or modify if you have any pictures of where the bracket is mounted or how it evem looks or any ideas on how to Fix i Appreciate it Thank you Don from chicago

[@RussToronto]

Hi Don sorry for late reply...I don't know if you fixed your chip shield. If u haven't send a pic and I'll look at [e-mail] Thanks

[@skojtv12]

Great videos Russ! Keep upp the good work. Have you tried to use the same type setup, but with the yellow jackets?

[@RussToronto]

U can use any pockets And teeth.Remmember its 2 left and write..then 2 straight then 2 left and write teeth. Doesn't matter but go clockwise if you like for teeth and pocket install.

[@UncleRoots413]

Wish you made vids when I started grinding. You on AS?? There is an excellent upgrade thread on there for the 252. I’m theammixman on there. Keep the vids coming!

[@RussToronto]

You there are alote of opinions on this..all I can say is the teeth ,becouse it's only 6 were down faster....but the stump is cut quicker becouse the revs stay higher...be good.

[@RussToronto]

Thanks gameface keep Cutting stump...

[@timpottenburgh5407]

Thank you for your videos I just bought one and if you don't mind I would like to pick your brain since it seems you know this machine inside and out my grinder was left outdoors and not used much from the guy I bought it from my grinder wheel does not rotate as smooth as you just turned yours and it seems like to be hanging up towards the top belt pulley and makes a rough sound when turning it by hand any thoughts? Cause I'm nervous about it being the engine bearing on that little belt...that you showed how to change the first pulley where you loosed the 4 bolts any way to lube that or what do you think? sorry for such a long and confusing question lol

[@vfreiress]

You'll need a pair of pillow block bearings. Vermeer's are expensive, so I get them at my local bearing shop at a third the price. Replace them both on the shaft that the wheel runs on (not that difficult if you're at all mechanically inclined). Remember to check the shafts that ride in these bearings when you have them apart to be certain they aren't also shot. I've learned that I need to grease these bearings with about four pumps from the grease gun, along with the two identical bearings about a foot higher up, EVERY DAY before I start operations, . If you follow that procedure this will be the last time you have to replace bearings in a very long time. There are a total of eleven grease nipples, some of which need more attention than the others (five are found on the hydraulic steering option if so equipped). Learn where they are and grease them with some regularity and you'll save yourself untold grief. Also learn how to adjust the main drive belt, and tighten it slightly when your hear the machine squealing or if the wheel slow or stops during operation.

[@RussToronto]

Hi it sounds like a bearing..if the noice is there when you turn wheel..engine of...with a screw driver handle agianst your ear.Use it like a stethoscope. Turn wheel and hear with one may be gone.

[@joelhill5099]

Can I do this with yellow jacket pockets and teeth?

[@RussToronto]

@@joelhill5099 Yes any teeth and pockets

[@RussToronto]

@@joelhill5099 yes u can