This is the best tutorial ever! Samsung should pay you for this
@petraotto9681Ай бұрын
Top, hab nach einem anderen Video nur das mit der Alufolie gemacht, was nichts gebracht hat. Aber der Hinweis mit den Zählerständen zurücksetzen war GOLD WERT!!!!!! DANKE
@FARABALE664 жыл бұрын
this video is the only one giving precisely the steps. Thanks a lot
@ahairstonification4 жыл бұрын
Thank you so very much. You saved me time and money. People like you are the reason good moral values are still in place
@eriktennant737Ай бұрын
Exact same setup as my C430W. Thank you for taking the time to make and share this.
@clearcreek69 Жыл бұрын
I was having difficulty removing the transfer belt & decided to go online for help. Thanks for this video
@Elnasir11 ай бұрын
Your video helped me detect why my transfer belt wasn't printing properly. Thank you.
@viandant511 ай бұрын
happy to help you!
@steinolavsletten25377 жыл бұрын
Lots of fellow print-users praise Your video, today I join the congritation of happy print-users with a fixed and working transfer belt !!
@JasonBlue-qn6zm Жыл бұрын
Thank you very much! I don't use my printer often, but for the last few years, it's been printing dirty. I followed your steps here, and it's printing like new!
@emilylaney4 жыл бұрын
A+ video! For anyone with trouble removing the wire clip: I had to use pliers to firmly pull out the wire connector. It was too tight to remove with fingers. No damages.
@ineterceptor6 жыл бұрын
I have different model, but the basic principle is the same. Thanx for saving me buying new printer! Merry Christmas!
@CreArtationUk3 жыл бұрын
Geat video and explanation thanks. I had a transfer belt fault on a CLX-3305. Completly taking apart as per your second half of video and cleaning has solved the problem👍 the only different thing I did was fitting the side springs before the outer cover was reftted. Acess to them was then easier.
@fredaustria21336 жыл бұрын
That was the solution for my big problem about the yellow lines on the C460W- Great....Thank yu
@freda27583 жыл бұрын
Thanks, guy! You saved me a lot of tears.
@thalakullick92727 жыл бұрын
Finally I did make it. Thank you so much! I just used a qtip (cotton) in order to entirely clean the residue container.
@acp15423 жыл бұрын
Thanks so much for this. I was on the point of throwing out this printer for
@zeckuss4 жыл бұрын
Thank you so much. Your video helped save our problem
@timdemeyer68444 жыл бұрын
Thanks a lot! Very detailed video and nice breakdown of steps!
@jamgonzaga67544 жыл бұрын
solved my problem !! Thanks to you, my printer's working again. Awesome, keep it up!
@Mcfa Жыл бұрын
your instruction helped me a lot. Thank you.
@hirmizzz4 жыл бұрын
Thanks a lot dear Viandant ! Very clear & detailed video
@clearcreek69 Жыл бұрын
I thought I fixed my problem yesterday but I printed something this morning & my printing is still smudging. I'm going to try cleaning the drum today
@friend4466 Жыл бұрын
Thanks for this video 👍 You did an awesome job explaining step by step. I fixed my printer myself following the instructions and it works again.
@vovanfun8 жыл бұрын
Thank you for the video! It was interesting, this model has not yet analyzed the transfer belt! Best reguards from Kiev
@viandant58 жыл бұрын
+vovanfun thank you, have a nice day
@pnp64086 жыл бұрын
Just saved me from buying a new printer. Thank you!
@gpmoja4 ай бұрын
Great tutorial
@ezrayates21754 жыл бұрын
Excellent informative clear instructions. My printer had been fine until I needed to replace the black toner with a new one and the next print was awful quality with faded strips. Followed your instructions and felt very comfortable with my execution of the process but unfortunately made no difference to the faded bits. Could it be my new black toner cartridge?
@viandant54 жыл бұрын
Probably the cartridge is defective. The low quality is on all colors?
@DerThomes5 жыл бұрын
Great Tutorial, well done and thank you very much.
@Thomasisport2 жыл бұрын
Super erklärt. Und bei meinem Drucker hats funktioniert. Danke
@WilfriedMehlhopLange5 ай бұрын
😎 SUUUUUPER- Thanks so much
@francoish96413 жыл бұрын
MERCI pour cette superbe vidéo !
@gerthuber22046 жыл бұрын
Very useful video, my printer prints clean once more. Thx!
@franciscofortunato18642 жыл бұрын
Muchas gracias por mostrar tu meticuloso trabajo!!
@kings_pride5 жыл бұрын
thanks, had to clean the transferbelt because there was some dirt on it causing white dots on black images :)
@tehsalt5 жыл бұрын
Thanks for the informative video, fellow human.
@jorgeiturri4 жыл бұрын
Excelente video... muy ilustrativo. Muchas gracias
@JuanCeSS Жыл бұрын
Muchas gracias me ayudo mucho tu video.
@mimi-c8o2s2 жыл бұрын
Tausend Dank für dieses Video!!! Echt super gemacht 😍
@AlinaDominikSanow Жыл бұрын
Good Boy, i love you for this Video 😙
@MK-hr5yv2 жыл бұрын
Great video, thanks👌
@Sarwiz13 жыл бұрын
Very good video
@philippebich16354 жыл бұрын
Bravo ça marche. J'ai pu tout nettoyer 👍👌
@herbertwild9837 Жыл бұрын
Verstehe zwar kein englisch, muss ich bei diesem sehr gut erklärten Video auch nicht. Herzlichen Dank
@viandant5 Жыл бұрын
There are the german subtitles
@marinesculucian65388 ай бұрын
Interesting and useful! How can you know how much toner is left in each cartridge? thanks
@viandant58 ай бұрын
The toner level? You can print the printer status kzbin.info/www/bejne/iKK8ao1tl699mac
@silsila50403 жыл бұрын
Hi, this video has been most helpful. Upon cleaning the transfer belt, it has started to make very loud screeching noises when calibrating and printing. What can I do to solve this issue?
@viandant53 жыл бұрын
I the unit has been correctly assembled, I think you have to lubrificate the cleaning blade of the belt, or wait until the loud disappear
@RaquelAFog6 жыл бұрын
Excellent video! Thank you so very much!
@ALCOSALUD5 жыл бұрын
Thanks a lot, Big help. When I need to made urgent print at wekend and my printer it does´nt work .
@nickfontannaz41765 жыл бұрын
Thanks for the clip, very helpful, I replaced the transfer belt with a new one (Samsung) however the Status light continued to flash any ideas? Thanks again
@viandant55 жыл бұрын
I've no idea, the transfer belt counter shuld be resetted.
@jimsteinhauer55103 жыл бұрын
This procedure will require going into the Tech menu to reset the counter for Transfer Belt (there are other KZbin videos on how to do this depending on the model, but it essentially a specific sequence of key presses on the controls: the display will read Tech menu if you are successful. For the printer in this video without keypad, the sequence is Menu, Back, Left, Right, OK, Stop/Clear, Menu. The C460 with a keypad uses Menu, #, 1,9,3,4, Menu. Once in Tech Menu, then go to Data Setup, then Clear Count (for the specific part you have replaced)). The mainboard doesn't "know" that the Transfer Belt (or any other consumable part) has been changed: resetting the counter is the only way to tell it you have completed the procedure. If you get error messages on any of these other "Consumables" and/or the Status light continues red/message appears you need to reset any of these parts, the Tech Menu is the only way to do this after you change out the part. Important: only change out parts once you have pulled the plug. Hot-swapping parts with the unit powered on may create problems with locking in error messages and may damage the mainboard processor.
@golfernst4 жыл бұрын
Excellent!
@user-yk7tu4dw2z Жыл бұрын
THANK VERY MUCH
@lamar9525 Жыл бұрын
Great instructions. Is there a replacement blade available?
@viandant5 Жыл бұрын
may be on alibaba
@lamar9525 Жыл бұрын
@@viandant5 OH, thank you I didn't think about them.
@MrCarissim3 жыл бұрын
THANKS FOR HELP ! :-)
@tuamigo643 жыл бұрын
Gracias por compartir.
@YelitzaDeColina-kp6zc5 ай бұрын
no hablo ingles pero estoy totalmente agradecida por su ayuda
@viandant55 ай бұрын
There are spanish subtitles
@marcocosby84037 жыл бұрын
You helped me big time friend
@drechenlard64917 жыл бұрын
you sir are a hero!
@pierregautier99808 жыл бұрын
Thks . it was very usefull for a 3170. it almost the same. now the printing are perfect.
@InspirationZoneandRelaxing5 жыл бұрын
Thanks for your help... It was very nice...
@SonjaSannert Жыл бұрын
thank you so much!
@sjakob522 жыл бұрын
Hi great video. I have the same printer. I bought black toner but it is not original - they promissed it would be just as good as the original. Now I am not sure why the black color is weak when I print. Would it help to maintain the printer (maybe I did something wrong when I mounted the black cartridge) or is the problem that the toner is not original. It would be nice to know before I start maintainance. Thank you in advace. Hope the spelling is ok.
@viandant52 жыл бұрын
I think there is nothing wrong mounting the cartridge. Probably the toner cartridge is defective but the problem could be the drum unit too. The compatible cartridge are often good quality
@pavelalf10 ай бұрын
THX 🙂
@bernardschmitt18134 жыл бұрын
Merci !
@liebbyelias24766 жыл бұрын
Should I still follow this video to try sort out the problem x
@Qlii256 Жыл бұрын
CLP-315 with transfer belt not being wiped. I did clean it and disasembled just like in the video. The wiper has two rubber parts that do the wiping. The bigger one came loose when I tried cleaning it properly however. I cannot find a replacement part. Do I need a whole unit or will just the wiper fix my issues? It seems like the wiper does not take off all the powder left on the belt for some reason.
@viandant5 Жыл бұрын
I think it's difficult to find the wiper blade. May be on aliexpress
@zelphx5 жыл бұрын
VERY helpful!!! Thanks!
@angelruz91194 жыл бұрын
thanks, i fix it
@OmaLisbethsMaultaschen7 жыл бұрын
Great Video!! Thanks a lot - I just exchanged the transfer belt! My printer now is printing again :-) However - the note on the little display "prepare for ne transfer belt" is still there. How can I "delete" or stop this message ...
@viandant57 жыл бұрын
I don't know any reset method, it should delete itself with the new belt
@emmyc93336 жыл бұрын
i can't get the transfer unit to stick back up in its original position, which makes it impossible for me to put the waste cartridge back. you make it look so easy. any suggestions?
@viandant56 жыл бұрын
there are no tricks, it should go into position without too much problems
@rabbitzki3 жыл бұрын
Hi, do you have a video showing how to change the Fuser in a samsung Xpress C480FW please?
@viandant53 жыл бұрын
it's similar to samsung clp 320/360, in this channel there is a video
@omaroufkir73526 жыл бұрын
thanks very mutch , شكرا جزيلا
@JudithLang13 жыл бұрын
I’m having problems with paper jams using glossy vinyl paper. Will this help if I clean that part?
@viandant53 жыл бұрын
No, probably the problem are the feed rollers, or the fusers
@vasilisntafos_Billy-Bo6 жыл бұрын
excellent...thanks man!!!!
@laurencemarks28337 жыл бұрын
Great video. I'm sure the ITB for a Samsung CLP-315 isn't very different. Does the belt itself ever wear out? The symptom is a blurry line maybe 6-10 mm wide across that page--sometimes yellow toner, sometimes black. Samsung literature says to replace the belt assembly. Is the real problem likely to be the wiper blade, or that the belt itself is worn out?
@viandant57 жыл бұрын
probably the belt itself is worn, and the wiper blade is one of the causes
@laurencemarks28337 жыл бұрын
Grazie, Signore Viandant. I've found that replacement ITB assemblies cost $US 65-$US 130. But replacement belts are $US 18-$US 20 from China and I now have one. I have a spare ITB assembly I can play with. I had one question, but now I have two: 1) Can I disassemble the assembly to the degree necessary to replace the belt? The Samsung repair manual suggest that this can only be done at the factory where special jigs are used. 2) Do you think that the wiper blade has worn in such a way as to damage the belt and would shorten the life of a new belt? Or perhaps that it's normal belt wear? (I realize that without seeing the blade both of us are just guessing.) I think I might go back to the China websites and see if the wiper blade is available. I love the CLP-315 and have used and used it. We also have a CLX-3175 (all-in-one). I have performed the special mods on both of these as described here: rumburg.org/printerhack/ . Don't try this on anything but a CLP-310 or 315 or CLX-3175. It takes advantage of a quirk in the firmware which was removed in later versions.
@viandant57 жыл бұрын
I've have a video on how to disassemble the belt. I think the wiper blade is ok.
@viandant57 жыл бұрын
I think that hack will work only if you do not have a new firmare version.
@laurencemarks28337 жыл бұрын
It seems to work on all CLP-315 and CLX-3175. It will BRICK any newer models. This is why I keep maintaining my old ones.
@marcindrozdz45437 жыл бұрын
Thanks for this video. i have managed to repair my printer
@ken3535232 жыл бұрын
hello, good afternoon, my printer marks the entire sheet with a very dark background, they told me that the problem could be the tape, if the tape is cleaned with alcohol and the blade, I will solve the problem or I have to buy the complete new tape, thanks .
@viandant52 жыл бұрын
Which tape? the belt? Yes you can try to clean it with isopropyl alcohol
@pattanantasb.10617 жыл бұрын
Very well thank you.
@renanramirez68054 жыл бұрын
Thank you!!!
@CydonianTR8 жыл бұрын
hello, thanks for these, great videos! I have a question, I have a samsung 3305FN printer and it gives 2 errors: "replace ITB" and "replace fuser unit". I know there is a chip resetting method for drum unit by soldering in drum chip but I want to learn if there is a way to reset "ITB=image transfer belt" or "fuser unit" with some chip soldering or anything like that??
@viandant58 жыл бұрын
Thank you, I regret but I don't know any reset method for fuser or ITB
@rahensbroek8 жыл бұрын
the reset chip is only for the toner/dv unit
@jessicaabigailscott7 жыл бұрын
Hi, thanks for your informative video. I bought a new transfer belt and fitted it as per your instructions which went well. But, when I turned the printer back on the error message "prepare new transfer belt" still came on. Any suggestions? Thanks.
@MrSuicycle5 жыл бұрын
After replacing the unit, you still need to reset the counter of the printer, which is done in the Tech Setup. To enter it, the combination of keys varies depending on the printer model - and unfortunately, Samsung didn't make them public (but they can be found for some models around the internet and on YT).
@thomasspielhofer32293 жыл бұрын
@@MrSuicycle It's usually 1934 for most models
@IanMcPherson_ab7 жыл бұрын
I performed the cleaning process, but the printer won't print colour anymore - just black and white - any suggestions?
@viandant57 жыл бұрын
a cleaning process in a CLP-365? I think it's a problem of settings
@IanMcPherson_ab7 жыл бұрын
I figured it out - I missed replacing the screw that holds the black flat plastic part at the end near the wires. After installing the screw (which I now call the colour screw) the printer works perfectly - no more ghost images and bright colours. Thanks again for the video it was excellent!
@cauvinh47746 жыл бұрын
Nice video.
@schanama8 жыл бұрын
Thanks!
@남극펭귄-n9k3 жыл бұрын
감사합니다 꾸벅~
@DanBurgaud4 жыл бұрын
How often do you need to clean the transfer belt? once every 10,000 pages or so?
@viandant54 жыл бұрын
Not necessary to clean it often. MAy be 30-40.000 pages if there are no print quality problems
@thalakullick92727 жыл бұрын
I couldnt make it. Perhaps, it was very dirty. I did everything you mention on the video and no. :(
@hphp-ny9wt6 жыл бұрын
ขอบคุณครับ=thank you
@bernardomalfavon95302 жыл бұрын
Hello, thanks for the video, I followed the cleaning instructions, but I still have a problem, when sending more than 2 sheets of some document, I get a ghost print of the watermark of the previous sheet, when I disassemble the transfer cartridge I notice that has remains of toner with the previous printing on it, apparently it is not discarding them, any solution? greetings from Mexico
@viandant52 жыл бұрын
Are you sure the problem is the transfer belt? It could be caused by the drum too and by the fuser rollers
@victoraguilars.42812 жыл бұрын
Hola Bernardo! has conseguido resolver el problema que mencionas? Me trajeron una impresora que hace exactamente lo que mencionas, un "fantasma" de la impresión, pero sólamente es en la siguiente página. y no existe un segundo fantasma...
@bernardomalfavon95302 жыл бұрын
@@victoraguilars.4281 hola, no pude resolverlo ya que no consegui otra unidad de transferencia para probar, lo que hace mi cliente es mandar a imprimir una hoja por una, y asi casi no sale el fantasma ya que el repuesto es costoso, va a esperar a que se le termine el toner para desechar el equipo.
@viktorin38x5 жыл бұрын
красава! всё аккуратно чётко!
@rogerdzul49657 жыл бұрын
No sabia que allan x el mundo tambien repara impresoras!!!
@danvee39287 жыл бұрын
Awesome!
@marcelolobfig4 жыл бұрын
I just replace the drum unit, a new cartridges toner, and the lights still blinking, all of them. I was wondering if you could get some solution to this problem. Thank you
@viandant54 жыл бұрын
There are no reset procedures. I think the problem are the chip. Are compatible cartridges? However Samsung make all they can to create problems to cartridges, even original ones
@marcelolobfig4 жыл бұрын
@@viandant5 the cartridges are compatible but not original and the image drum unit chip was already replaced. Could it be the transfer belt? Many thanks
@viandant54 жыл бұрын
@@marcelolobfig Yes, it could be the transfer belt. Check the printer folder to have more informations
@abdulhakeem_tweel5 жыл бұрын
The right plastic lever shown you opening from the minute 1:18 was suddenly fell down of my printer, I tried to return it back but couldn't know how, any help?
@viandant55 жыл бұрын
probably it's broken, try to reassemble the printer without that lever
@armandas1017 жыл бұрын
How do I find out what error my printer has ? Because it is flashing red and not printing I don't know why
@reinhardschiffler93946 жыл бұрын
das hat mir geholfen !
@daisygreen52253 жыл бұрын
Can I use hydrogen peroxide to clean it as a substitute?
@viandant53 жыл бұрын
No, better the normal alcohol
@robertopattaro88754 жыл бұрын
hi, i have do this deep cleaning but after doing that my printer print only in grayscale. I dont understand why? You have any idea?
@viandant54 жыл бұрын
What is a deep cleaning? Check the printer settings in the printer folder, may be it's set in "Grayscale"
@MultiEscaper5 жыл бұрын
Хорошо видно на видео как происходит замена .
@stephenkenny32817 жыл бұрын
have a problem with my Samsung clp-365w. On power up it doesn't go through its usual warm up procedures. It is connected to the computer via usb. Removing the usb cable causes the conputer to sound so it knows it is disconnected from the computer. I think it is a hard wear problem with the printer itself. I have recently emptied the wast container. I worked after that but one morning after I powered up the printer all lights on the display came on steady and the printer didnt go through its usual warm up proceedures.
@viandant57 жыл бұрын
the waste toner container has a fuse, it needs to be reset
@stephenkenny32817 жыл бұрын
viandant5 how do you reset the fuse. I have tried cleaning the waste container
@viandant57 жыл бұрын
I do not know any reset method
@stunetwork1014 жыл бұрын
What is the problem when the pick up roller won't engage? It won't turn.
@viandant54 жыл бұрын
II think it's not an electonic problem to the main board, you should have an error message. It could be a mechanical problem, a gear or something not in the right position
@Suselinchen13 жыл бұрын
can i do this for samsung clp300 too?
@viandant53 жыл бұрын
No it's different
@sofiamiranda64774 жыл бұрын
Hello, i have a clp 315 and i cant remove the drum unit, seems like its stuck?
@viandant54 жыл бұрын
Yes, it could happen i's hard to remove. Try to move it up using a lever or a screwdriver then pull it out