Disassembly/Reassembly Brother Laser Printer MFC-L2700 L2710 L2750 and others

[@puremotion2212]

WOW !!! Thank you, thank you, thank you !!! I dismantled, removed three stuck pages; and reassembled following your instructions. I truly appreciate your sharing your knowledge.🥰 mars 2023

[@arklas]

This video helped me remove jammed adhesive paper, wrapped around one of the rollers in the fuse assembly, from my L2710. No side effects of the repair so far. Thank you!

[@sadddee]

Not being smart enough to line up stripped pieces, I spent hours looking for where I had taken from a piece of metal. Thanks to your video, I found it was sitting near the fan at 9:29 in your clip. Thanks a lot!

[@BernieMasters]

Thank you. Your video was completely accurate in showing me how to disassemble the printer until I could reach the paper wrapped around one end of one of the rollers. Paper removed and problem solved. Much appreciated.

[@JesusSwearingen-vo1yx]

The printer was a bit complicated to hook up kzbin.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 but it does the job very efficiently. I like the ink wells versus the ink cartages that cost an arm and a leg. It prints quickly and the quality is excellent. It shuts off when not in use, so you have to remember to turn it on. Overall, it exceeds my expectations. I'll update my review in a couple of months.

[@jon3voltas]

Thanks for this. My MFC-2700DW was a breeze to clean with this video!

[@MikeCarey101]

great video- installing the rear panel is a lot easier if you just close the cover and let the 2 pins of the 2nd fuser cover slid into the slots, then down into the track (instead of trying to bend them into the track)

[@Ivansindell]

I need to disassemble the scanner feeder, your wonderful video showed removing he cover, but not disassembling the scanner feeder. Thanks

[@wanzi57]

❤ Thx 4 this great video. It was very helpfull 2 repair my MFC 7200 ❤

[@jimmyz9786]

Nice video. No need to remove ADF to replace fuser.

[@joeikt17]

Thanks for making this video. We have paper jam error and there is a weird rough sound coming from the printer. Haven't remove the fuser unit. Might have to do that to get it fixed soon.

[@steveschmoe6870]

I was able to follow your instructions down to 1:27. I do not see anything resembling what you call "the front cover" on my L2750. It would have helped had you started the segment a little further away from the device so that I could see what side you are zooming in on.

[@steveschmoe6870]

Never mind. I found a wider view in another video which shows me where the "front cover" is located. I managed to work my way down to the power plug, which needs replacing.

[@efficientcartridgesprinter5415]

relay good ti heals for all model of brother thanks for video

[@shelleyotero7357]

I have the MFC-L2720DW. I bought a memory module following a different Brother page, but I don't see where it would go. Do you know if this module support an increase in memory?

[@viandant5]

Often they are inserted in the main board. some machine has a panel under which there is a slot on the main board

[@sravanrenjith1815]

Thank you so much for the wonderful video. I have gone through your video to clean my Brother MFC - L2703DW printer. There is some burning smell coming from my printer and I open all the parts that you mentioned in the video. I realized that there are some insects inside that. I also noticed that the insects in the mainboard and its surrounding areas as well. Your video is not explaining how to remove the area nearer to the mainboard. I have removed all the screws from there and there I have noticed grease or something adhesive and some components (gears) fell down and I could not fix it. Could you please help me to get rid of this problem? Thank you

[@viandant5]

Sorry I've not that model of printer in my office so I can't take a photo. Here there is the service manual, I hope it can help you www.manualslib.com/products/Brother-Mfc-L2700dw-3562246.html

[@sravanrenjith1815]

@@viandant5 Thank you for the reply. I think that is also similar to the one that you showed in the video.

[@sravanrenjith1815]

Would you be able to provide the image of the same one that you are displaying in the video? Thank you

[@viandant5]

@@sravanrenjith1815 Sorry I have no more that printer

[@shraddhakhatri9535]

sir same proccess brother dcp 2541 dw ?

[@viandant5]

It's similar but it's not the same machine

[@407Tengah]

Thank you for this video, I had a visible paper jam stuck around the orange fuser roller, only needed the 1st 2 steps to remove the cover for enough grip access to the jammed paper. But what a godsend, always worried about using too much force on plastic parts.

[@jamkpa]

Great video! Question, on a Brother MFC-9130CW what side is the Power Supply so that I can replace the Super Capacitors? Thanks.

[@viandant5]

It's on the right

[@jamkpa]

@@viandant5 Thank you for the jet fuel laced fast response!!!

[@AshokSingh-pv4ze]

Thank you for your video. My printer assy printing pure black print, no image on paper, drum assy changed, what could be the fault.

[@viandant5]

The drum unit for start, or the Laser scanner unit

[@mahaveerinfotech7623]

Sir you have done a grear job

[@anggara722]

Sir please...how to clean scanner unit brother l5600dn...tutorial please...

[@viandant5]

Sorry I haven't that machine

[@mschf_nft2581]

I just needed to replace fuses cover. Now when I re assemble says "paper jam rear" and won't go away help

[@mschf_nft2581]

@viandant5

[@viandant5]

@@mschf_nft2581 I think you have to check the paper sensor of the fuser unit. may be one of them is out of position

[@mschf_nft2581]

@@viandant5 the fuser unit is the orange cylinder, but what it would be the paper sensor ?

[@viandant5]

a plastic flag or a photodiod

[@fenix0green]

10:01 Do you have a picture or video on how to take those gears off and put back on? Their is a spring on my printer that is out of place and clicking when the gears turn

[@viandant5]

Sorry I have no pictures

[@BeeTammo]

Hi, I have model 2710DW and I had paper error 09 I watched other video of how replace the plastic part that check the drawer in, but it was different from the video I saw and now I have all the gears disassembled is there a way to figure each gear where it goes or do you have a video for that? Thanks,

[@viandant5]

Sorry I only have this version of the fuser unit, I never hear of another type of fuser unit

[@johansyah8929]

Good job sir,can you help me ? after I servis mfc L2700D on screen mesage front Cover open,what problem a bout that? Thansk

[@viandant5]

May be the sensor of the cover is broken or out of position

[@johansyah8929]

Ok thank you very much mr@@viandant5

[@arGow]

How to disassembly a Brother MFC-J461? Il doesn't start anymore, no light thanks

[@viandant5]

Sorry I have't video or manuals about this printer. It could be a power supply problem

[@soloturk8856]

please show how to reassamble brother mfc 1811 fuser press roller. waiting for video. thanks.

[@viandant5]

I have no that machine in office. If I have one of them I'll do the video

[@repeatman]

Everything on mine works just fine, when I go to print it acts like it will print then stops with a paper jam error.

[@viandant5]

Probably something was not reassembled well. try to disassembly and reassembly again

[@angelonavarro7461]

How to fix no display panel board dcp2540dw

[@viandant5]

I think you can only check the connections with the main board

[@bluedrew]

I have "paper jam inside" msg with no paper jam. Entered service mode and did sensor check. All sensors work except front registration. How do I get to registration assembly to make sure levers are connected? Service Manual says to only remove Right side cover, and HVPS PCB first. How do I get the registration assembly open to check the levers?

[@viandant5]

The registration assembly should detect the edge of the paper and should be near the fusers where the sheet come out from the printer. It should be connected with the main board

[@ovidiojoseponzo6687]

Tengo una impresora láser Brother HL 2270 DW, cuando la desarmé para limpiarla se salió un resorte pequeño de tracción de aproximadamente 1cm x 0,35 cm. Ahora las impresiones me salen con franjas horizontales, y espaciadas regularmente, me podrían orientar dónde debo reinstalar ese resorte??

[@viandant5]

es difícil, si tuviera una foto tal vez podría ayudar

[@rcb177]

Ladies & Gentlemen, I suddenly started getting the message "No Toner" although I replaced it with a brand new Brother toner kit. I cleaned the contact leads but, the message does not go away. I would appreciate any suggestions to have this problem fixed. Thanks. RC.

[@viandant5]

Try this: kzbin.info/www/bejne/mnXEc2qmpa5_nac

[@markraptus]

Hi there, I need your help please, I need to know wich kind of diode is the one next the super capacitor you can see in bottom right corner (min. 4.07 of this clip). please can you tell me its voltage?

[@viandant5]

Hi sorry I ca't help you. I have no tech manuals

[@markraptus]

@@viandant5 if you have time perhaps you can have a look on it with a magnifier, it should be a "C91" (91volts). Unfortunately mine is burnt and impossible to read.

[@viandant5]

@@markraptus I've no Brother MFC-L2700 in office

[@foreverfriday5644]

how many papers was printed by this printer?

[@viandant5]

I don't remember

[@aldwinnuguid4472]

1:15 you should have removed the bottom tray between the paper tray and the roller before you remove the black plastic guide instead of forcing it out using a screwdriver. Without doing so you will break the black plastic and thats how you break your printer

[@viandant5]

thank you for the tips but no break problems

[@syifaservice6999]

nice, thanks for info 👍

[@antongiulioleuzzi1167]

buon giorno avrei bisogno di aiuto : ho una brother mfc l8850cdw e da un p di giorni stampa con sottofondo di tre bande orizzontali colorate da 10 cm circa nella sequenza: azzurro , violaceo, marrone arancione o nero. oppure un mix di quelli con dei cerchi arancioni da 0,5 cm di diamentro a distanza di 2 cm uno dall'altro nell'intera pagina oltre a striatura a distanza di 5 cm o 15 cm ello stesso colore dei cerchietti arancione marrone. lamp o altr?grazie per il tempo che vorrai dedicarmi

[@viandant5]

A me sembra un problema di contatti, forse il tamburo ha delle imperfezioni e scarica a massa, oppure è un problema di filo corona. Prova intanto a togliere e rimettere il gruppo tamburo

[@antongiulioleuzzi1167]

@@viandant5 grazie in realtà ho già smontato la lampada se c'è qualche controllo che posso fare prima di montare tutto me lo indicheresti

[@antongiulioleuzzi1167]

@@viandant5 ora che ci penso mi diceva voce di errore "uno dei quattro toner non è correttamente infilato nel tamburo....

[@viandant5]

@@antongiulioleuzzi1167 Non mi sembra un difetto legato ai fusori, di solito è un problema di carica del tamburo del rullo di carica o del corona

[@antongiulioleuzzi1167]

@@viandant5 grazie sei molto gentile ma come posso risolverlo ? ti sarei grato se mi aiutassi a trovare tutorial per risolvere e siti per acquistare prodotti questa è la mia mail [e-mail] per ogni richiesta. grazie per il tempo dedicatomi . cordialità

[@RealKEC]

Thank you!

[@ioannispapas9477]

THANKS FOR VIDEO SCANNER

[@jonlu003]

Buon giorno, innanzitutto complimenti per il video, decisamente ben fatto. Ho un problema alla mia stampante Brother multifunzione (MFC-L2700DN). Improvvisamente mi ha restituito l'errore di inceppamento interno. Mi chiede di togliere il toner e di verificare se c'è della carta inceppata ma non c'è nulla di visibile, nè frontalmente, area toner nè posteriormente, gruppo fusore. Potrebbe essere una questione di sensori? Ho il tamburo al 75%, può dipendere anche da quello? Sono riuscito ad accedere al menu manutenzione e col codice 32 ho avuto modo di testare, almeno credo, i sensori ma non mi viene restituito nessun messaggio di errore. Se ti spedissi la stampante me la ripareresti? Dal check sensori ottengo queste linee di testo: C1NTCVRCPO__RA, MAC 24C (termistore) e DFDR****AC****. Poi ad ogni cambio linea sento una serie di bip. Pare manchi il riferimento al RF sensor (Registration front sensor), al posto delle lettere ci sono due trattini bassi (underscore). Non saprei.

[@viandant5]

Salve, non conviene spedirla, se contatti uno della zona risparmi. Prima prova questi metodi kzbin.info/www/bejne/r4m6mKtuopKaj5I

[@jonlu003]

@@viandant5 Ho fatto anche le prove del video. Non ho smontato il gruppo fusore o altro ma ad occhio sembra non esserci nulla. Quanto mi costerebbe una riparazione , più o meno? Che cosa sospetti che sia? Ho anche notato che non prende il reset di fabbrica. Ho ancora tutti i numeri in rubrica e l'indirizzo ip impostato manualmente. Mi sono limitato a togliere un paio di sportellini del retro per visualizzare meglio il gruppo fusore.

[@viandant5]

@@jonlu003 Potrebbe essere un sensore carta difettoso o fuori posizione. Non so quanto verrebbe a costare, magari chiedendo un preventivo prima se è qualcosa da poco tipo un connettore staccato non costa molto

[@jonlu003]

@@viandant5 Ho notato che anche se tolgo completamente la carta non mi dà l'errore relativo alla mancanza della carta. Questo avvalora l'ipotesi del sensore? Ho anche provato, ripeto, a resettare la stampante ma non prende il RESET. Sono andato da menu, reset di fabbrica. Premo ok ma non succede nulla. Non è che c'entra la scheda madre? Quando faccio il reset non dovrebbero sparire anche i contatti rubrica, l'indirizzo IP ect? La stampante non arriva nemmeno a caricare il foglio, si blocca prima.

[@jonlu003]

Smontando alcune parti, dopo aver seguito il video, ho notato nella parte degli ingranaggi in plastica, una molla che sembra essere isolata all'interno del suo alloggiamento ed un paio di ruote dentate atte al raccoglimento della carta isolate. Quella molla c'entra qualcosa? Posto una foto: drive.google.com/file/d/1tUJrGkcvWUoRdUXewZ_dznOHBDVNDBM-/view?usp=sharing

[@whasappaudios]

good

[@ง่วงนอนนอนละฝันดี]

Thx

[@nawatime_titha]

❤❤❤❤❤