Late to the party, sorry. Over revving usually means an air leak, so...Change O rings on starter, Carby, and two on the inlet manifold (with one O ring, you need to take the manifold off the engine block by unscrewing both mounting screws). Make sure the venturi connection on the engine block is free of gunk, the end hose of the carby connects to this, as the vacuum can be affected if it is blocked and it will rev almost to the moon, so try pushing some wire back and forwards through the little pipe there. Also make sure that hose is clear. Make sure there aren't any leaks in the snorkel hose or through the filter housing itself; crimp the hose in various sections (with your hand) to see if the revs lower when you do. Try placing a small brass washer or two under the carby lifter. Last of all, if none of the above works, try putting the poppet valve in on the "B" position rather than the "C" position. You can even try "A" if you like. C is leanest mix, followed by B setting, and A is the richest setting. Good luck (if you are still fixing it).
@mudzy9820 Жыл бұрын
im having this issue, done the carb seals, cleaned everything, only thing i havent done is engine seals but if i disconnect air hose from filter it lowers rev a tiny bit
@greggregson9687 Жыл бұрын
@@mudzy9820 Try following the advice I gave above, in order of ease. Over revving is too much air, or loss of vaccuum. Rarely, it can be fuel starvation, but this usually cuts the engine (or stops it from even starting).
@rogermcdonald16072 жыл бұрын
Good job Phil and congrats for going over 300 subscribers sir!👍🇺🇸🇬🇧
@GuysPlayingWithTools2 жыл бұрын
Interesting carb, I haven't seen one of those before
@andrewsmowersandsmallengin86432 жыл бұрын
Great video mate hope you're well
@themowerman2 жыл бұрын
Well it goes on.. I'm sure you will crack it mate
@henrymurawskibigdogrepair2 жыл бұрын
Keep up the good work you’ll get it Phil
@markwiley95162 жыл бұрын
Phil you will get it right just keep going on it
@Big_Johns2 жыл бұрын
Nice video Phil, on that carb does it have any check valves in it, sometimes if the check valves go bad of get damaged it'll cause the high revving. And hey, you're looking good brother.
@mowtoegee7049 Жыл бұрын
Like already said it will most likely be an air leak somewhere. Greg gregson mentioned everything to check. If for any reason it still playing up after all those things (which will solve 90% of the time) you can try to fit a small washer onto the carburettor body under the cam plate. Sometimes the cam plate can wear down over time and the engine behaves its got an air leak, but its not. so the washer is to push it up very slightly
@almclean48352 жыл бұрын
Odd looking carb, not seen one like that before. I’m sure you’ll get the issue sorted.
@mr1pearl2 жыл бұрын
Well you have my attention on this one I've never seen one like that really different ! Hope you get it sorted and please document it I'm really curious. Usually high revving engines is governor related 🤷 Also that spring looks really long but hey it came out of there absolutely stumped !
@colinjamieson86092 жыл бұрын
you can add brass washers/shims CR03619A buy from dc spares these take revs down.
@henrymurawskibigdogrepair2 жыл бұрын
Conquer that’s a two stroke should be able to adjust the fuel mixture and back off an idle and that should be OK but I’ve never seen a motor look like that before
@trevorwinkworth1208 Жыл бұрын
man where are the on off wires that go into the carby. they must have made different carbys for over seas models. i have 6 victa 2 stroke mowers there fantastic
@garyclifton21802 жыл бұрын
Gd luck Phil sorry I can't help but a interesting video IV had a Briggs for 20 years it's not run for last ten problem was it was working I went to work my son cut the grass I tried week later it revs it bits of so just got put away
@Salmaanfredericks-ne6hr9 ай бұрын
Where can I buy this repair kit
@trevorwinkworth1208 Жыл бұрын
did you sort it out mate
@BrucesShop2 жыл бұрын
Yes a pressure tester would identify your issue.
@stumpyssmallengines2 жыл бұрын
i know you will fixit phil
@Big_Johns2 жыл бұрын
Where have you been hiding Stumpy? 🙂
@stumpyssmallengines2 жыл бұрын
@@Big_Johns I’m back John been so busy sir hope your well
@Big_Johns2 жыл бұрын
Yes sir I am, just checking on you, busy is good though. 👍
@TheOldFatBastard7 ай бұрын
That’s a victa for ya lol might just be old and warn out mate