Long Crease On A Quarter Panel Fixed With No Paint

[@ianwatches]

You're an artist.

[@vidicz]

Thank you much appreciated.

[@DZ32100]

Hey Zan buddy ! Bobby Zee here from Dent Zero. Great video

[@vidicz]

Hi Bobby. Thanks for watching.

[@DZ32100]

@@vidicz Always Brother

[@royalmotors]

Great video Zan. Can I ask - as you're working left to right along the crease, I can see the paint flex. What I can't tell is what the tip of the tool is doing. It looks like you're pulling the tip downward from just above the crease to just below it, but then again you may just be using the point of the tool to push outward from inside the panel. Can you explain the direction you are putting the force on the tip of the tool here?

[@vidicz]

It looks like this because I had a hard time hitting the center of the crease because it had a sound deadener on the inner side of the panel. That made it harder to push the center.

[@royalmotors]

@@vidicz I understand the sound deadener mass it more difficult... So you were pushing - not sliding the tip?

[@MSXRECORDS]

@@vidicz so to be sure you was pushing not sliding the tip?

[@CarbageRacing]

So are you pushing directly in the center of crease or above it? Looks like above it the whole time. Thanks

[@vidicz]

In the center. It might be the way the light breaks in the recording.

[@p.bexiga7967]

You are PDR black belt !! 👍

[@vidicz]

I try my best 😌 thank you 👍

[@billcui7827]

good job always. thanks you for sharing.

[@vidicz]

You are welcome 👍

[@keithreeve5911]

Great video show just how finely tuned your work is, more practise for me though.

[@vidicz]

Thanks Keith! You will get there 👍

[@inkanthem]

How much could one charge for a repair like this?

[@vidicz]

It all depends on the market you are in

[@vjekoslavcvetnic7500]

Da li plougama kada pritišćeš vrhom alata udubinu isključivo pritišćeš okomito na udubinu (iza lima) odnosno pikaš okomito (iza lima) ili pritisneš pa pod pritiskom kliziš i rotiraš polugu kao da peglaš neravninu (iza lima) i peglajući vrhom pod pritiskom izguravaš neravninu klizeći alatom (iza lima)?

[@vidicz]

Ovdje sam pikao ali ponekad se može i klizati sa alatom.

[@vjekoslavcvetnic7500]

@@vidicz , hvala na odgovoru! Gledajući sve izgleda lako, kada treba sam početi bude 1000 pitanja...

[@BonanoTM]

Thanks for the video

[@vidicz]

You are welcome 👍

[@davidaguilar2866]

How long did this repair take curious

[@vidicz]

Took about 2 hours in total with filming and all.

[@dentowlnorthwestirelandden4019]

Great repair 👍

[@vidicz]

Thanks 👍

[@dominikk3677]

Top work

[@vidicz]

Thank you Dominik K!

[@allenchandler1034]

great job.

[@vidicz]

Thank you Allen

[@nerma4597]

Super video, hvala

[@vidicz]

hvala tebi 👍👊🏻

[@SrbijaParacin]

Bravo svaka Čast 🎉🎉🎉

[@vidicz]

Hvala!

[@andrewbaird509]

Good job 👏 good skills

[@vidicz]

Thank you Andrew

[@viktorolishkevych7316]

Super.👍💪

[@vidicz]

Thanks 👊🏻

[@sergeipanteleev1204]

MASTER

[@vidicz]

🙏

[@razaqureshi5538]

hi teacher

[@vidicz]

Hello Raza

[@Kantry70]

👏👏👏👏👏👍👌😉😎

[@dentsoff_abolladurasfuera_8839]

Nices🤙🏽🤙🏽

[@vidicz]

Thanks

[@Marco-qe5zw]

How much does a repair like this cost?

[@vidicz]

Prices would greatly depend on the location of where car is being repaired. They vary a lot from country to country