Music Played By: Miguel Sequeira Bringing the Losi off the shelves and back into bashing! Any questions please comment, I should answer hopefully.
Пікірлер: 26
@sparkiegaz3613 Жыл бұрын
Still got mine very minimal use ,,❤
@Ghostmaker36 Жыл бұрын
Now I want to get one and make it a monster truck with cage and update wheels and tires etc
@Jotrades4205 Жыл бұрын
Great resto! Soundtrack rocks!!
@nitronorsemen863 Жыл бұрын
Keep up the good work
@joshherrman320110 ай бұрын
Hey man, first off, I just want to say thanks for your help. I have 30 plus rc cars and just picked up my first nitro lst with a 454 in it. Thanks to you, that new carb on runs flawless. 2 question what did you use for the header seals? Second, when you did you 454 swap, what did you use for a pull cord? My cord is starting to fray. Thanks again for your help.
@haywirerc10 ай бұрын
Exhaust seals I used dynamite for block to header and protek for header to pipe. Proteks fit loosely on block but fit good for pipe seal. I had old Lrp pull start laying around, rebuilt with different cord it but is pretty much same thing. I watched the video and saw forgot to mention that the Mach .26 pull start didnt fit Mach .26ss backplates (backplate used on 454). Sh engine pull cord might be same as lrp as they are under same company, but I did break the lrp pull starter and abused it again when I rebuilt it and it hasn’t shown any wear.
@haywirerc10 ай бұрын
I also just posted video but did miss a lot of points so keep reaching out if you have more questions!
@bajzatandre Жыл бұрын
great job on the resto/video/tunes. Check tank pressure at the primer and cap. Could cause it to run lean at higher rpm. I see its rich on the low and then leans...
@haywirerc Жыл бұрын
Drove the truck around today and was running ok but there’s definitely a leak in the tank as it’s very lean and fuel is not getting to carb quick enough like you said. Primer had never worked for the entire time I’ve had it and I looked at cap o ring and it needs to be replaced.
@thomrose9119 Жыл бұрын
To fix cracked spots super glue or epoxy stops it from getting bigger
@carlyvallejos523 Жыл бұрын
No es vintage . .. vintage son de mas de 30 años
@thomrose9119 Жыл бұрын
Oh sorry this is D.& T. Toxic RC
@Jotrades4205 Жыл бұрын
😀👍
@beevang1668 Жыл бұрын
Where did you buy the body shell?
@haywirerc Жыл бұрын
Amain hobbies Chevy long bed extended cab
@chopers49Ай бұрын
Can anyone help me with the needle setting
@haywirercАй бұрын
High speed and low speed should be flush but right now I have my high speed one turn down from flush and low speed is two turns out for me. Good luck and your tune should be around there.
@haywirercАй бұрын
One turn leaned on high
@chopers49Ай бұрын
Thank you very much
@nrachewy5961 Жыл бұрын
what does it run off of nitro?
@haywirerc Жыл бұрын
30% nitro 10% oil mix
@user-cw7oi1ib2q8 ай бұрын
Is this LST a vintage one ?
@haywirerc8 ай бұрын
First version LST. I consider it vintage but they were made in 2004.
@user-cw7oi1ib2q8 ай бұрын
I got one , but i lost the wheel hub adapter , could you tell me which model its fit to replace , because i can't find the original one
@haywirerc8 ай бұрын
@@user-cw7oi1ib2q not totally sure as unfortunately the 14mm hub has a strange offset