Check out this 2110 build! It's going to be wicked! #vw #aircooled #race VW 2110cc Engine Build, Part 1 - Type 1 High Performance air-cooled racing engine, Volkswagen, VWDB VWD,
Пікірлер: 177
@VWRICH234 жыл бұрын
I could just watch this all day...even at work lol
@vwdarrin4 жыл бұрын
Thanks man!
@johnrideout71243 жыл бұрын
I bought a vw van that had a terrible clanking noise from the engine. I couldn't wait to pull it apart to see the cause. Two hours later I was looking at a crankshaft that was broken in half inside the centre main bearing, at the same angle as the oil drilling. The clanking was caused by one half under load, followed by the other half as the cylinders fired.. This was in Australia, and I knew the driver, he was always labouring the engine, which caused the break. But I had never seen or heard of a broken VW crankshaft before.
@toddmichaeljaniszewski4 жыл бұрын
Your videos are always fantastic. As an amateur engine builder, I've been so happy to go over your engine build vids again prior to my attempts. Alas, I wish I had access to a shop/tools/machining you have access to. There's nothing remotely around me so I'm left to my own learn from books and videos!
@vayabroder7294 жыл бұрын
Love 90.5 mm cylinders; great for street motors. 1776 or 2110 are the best. And CT is in da house!! Thanks for sharing, sir!
@vintagespeedvw78644 жыл бұрын
Street car motor track night. All sounds good to me. I should have mine all together soon for a track night. Good stuff Darrin.
@GregsGarage4 жыл бұрын
I always enjoy the engine builds! That 2110 looks pretty bad ass.
@VWWRENCHIE4 жыл бұрын
VW Darrin..one of the BEST.👍😎
@vwdarrin4 жыл бұрын
Thanks man!
@bartwineland16293 жыл бұрын
Another great video. Thank you! Can't wait for the type 4 build.
@rlprgp623 жыл бұрын
Darrin, Love the build. Looks really good. Thanks for sharing...
@jojomojo94393 жыл бұрын
Great video Darrin! Thanks for all the great VW knowledge.
@newmantv56683 жыл бұрын
Thanks for the video looking to purchase a bug over the weekend, first in over 20 years.
@briandouglasbell3 жыл бұрын
Darrin!!!! it's so awesome that you're back teaching us again....more type 4 content would be great as well...thank you SENSEI!!
@modotvideo4 жыл бұрын
Thanks VWdarrin for sharing your knowledge
@vwdarrin4 жыл бұрын
Thanks for watching!
@demetricshorter69533 жыл бұрын
@@vwdarrin sir, do you have an email address or contact information you share? I have a VW (1600) engine I would like to ask questions about. My email is Dnshorter123@gmail.com Any help is greatly appreciated
@Cmnore2 жыл бұрын
Getting ready to build a s/p 2110 for my bay window and your videos are invaluable. Thank you for your excellence
@Buckswoodshop4 жыл бұрын
Big Thumbs Up Mr. Darren!
@vwdarrin4 жыл бұрын
Thanks Buck!
@twodacurb4 жыл бұрын
I just started watching you vids,I think you are THE VW MAN, THE MAN. Thank You very much for all your VW help over the years. I'm also glad you recovered from your health scar.
@snocrushr4 жыл бұрын
Watching 👀👍👍
@airheadvw44794 жыл бұрын
Talk to brothers machine in California they build alot of type 4 stuff. They have good stuff they did my heads for my 2 liter
@123rusty4 Жыл бұрын
CT in the house !
@racekar8010 ай бұрын
Can’t believe you use ultra grey, Porsche and motorcycle manufactures use an anaerobic sealant for engine case half’s. Honda and Yamaha have an excellent product. I have used permatex right stuff which is very good as well.
@Doubleodude3 жыл бұрын
I love this thank you Darwin and CT
@BusGreaseMonkey3 жыл бұрын
I’m going to do two builds soon. One stock 1600 and one performance build. I’m excited to play with these little engines.
@michaelmcclown55933 жыл бұрын
Dam you get around, Dangar Marine and vwdarrin 😁.
@rheidtech4 жыл бұрын
Really like what ur doin man. Appreciate your drive👍🌄🇺🇸
@jpaull4 жыл бұрын
That looks like its gonna make some power!
@SladesVWBeetle4 жыл бұрын
I always enjoy your engine build videos !
@jhao18644 жыл бұрын
Awesome job
@kabochii_mlbb22762 жыл бұрын
Me and my husband are both volkswagen lover here in Philippines... I uploaded also the volkswagen engine he rebuild... And I am so proud of him....... God bless and keep up the good work sir!
@VWWRENCHIE4 жыл бұрын
That Ultra Grey is great stuff..its factory spec on my Toyota oil pan..vibration resistant.😎
@jaytownley722 жыл бұрын
Love your videos Darrin, been a big fan for years 👊🤙
@danielmccoy85124 жыл бұрын
I think this first time seen with flywheel installed, before the case half together.
@throttlebottle59064 жыл бұрын
easier to rotate and check things during assembly
@gti6664 жыл бұрын
Always I learn new tips with your videos. Thanks for share us!
@VWJawbreaker4 жыл бұрын
Track night when it cools down.... sounds good to me.
@adamUDavies3 жыл бұрын
I could watch you put motors together all day long. Great video 👍 I had a 2275 built and the guy painted it black , claim's it helps disapate heat. He said Harley Davidson does the same thing ? Wondering if anyone else has done this ?
@craigmonteforte1478 Жыл бұрын
I enjoyed watching this video for myself at nearly 60 years of age it’s been many years since i’ve had a VW Aircooled engine opened up. ironically my last one was a early 70s Beetle in 1984 ish i bought a crappy Bug that was running on 2 Cylinders it drove across town home. at Midnight and with a Flashlight we saw twomPlugs dangling on their a wires out of the Heads the next day i discovered those Heads were stripped out and my local VW Repair shop sold me my very first set of Heliocoils and told me how to install them which i did the motor was a Leaky one and i pulled it to put in a newcGasket set that came fromBrazill complete with 4 Pistons and New Rings for $117.00 everyone told me they were Junk and not last that Bug was one i gave my little Sister as a College Car she beat the hell out of it and drove it for a few years then gave it back to me running years later i pulled the motor and gave the Rusted body and Pan to a ScrapYard and from what I know that motor is still running in its 4th or 5th Air Cooled VW over 35 years later FYI the VW Enthusiasts in my Home town is a small group and a few. oth them i still keep in touch with and have given me tabs on that Engine Block for funsies i grew up,inSouth Florida and we had a Business there called The Beetle Shop that had a large group of Bikers working there and that shop built high performance Motors for the localKit Car Company Classic Motor Carraiges that built a lot of the nicer Porsche Speedster Replicas using Type 1 VW Pans and engines that shop bored and Stroked the Blocks and for years they used a Shortened Transporter Bus as their Shop,Truck it was so rediculously shortened the People in the Front Seats could touch the rear Window from that position it was made to,look like.a Surfer Bus and i’ve seen them pull the front Wheels off the ground from a dead Stop ! We had that and a old Fiberglass Boat someone put on a Modified VW Pan that has Survived into a Marketing Tool for acRea Estate Company Locally i saw it 20 years ago and it looked like it could be a runner but was used as a Static display Vehicle only it was Parked in A Restaraunts Parking area with a lot of Traffic goin by it daily
@gregparker99432 жыл бұрын
Thank you for sharing your build. Although, I do have several questions. 1. Self sealing nuts are not designed the way you installed them, 2. I noticed that you did not adjust the torque wrench for the smaller studs and allow for the nylock added frictional torque value to add to the final torque for the 8mm nuts. 3. During your torquing of the main studs, I noticed the torque wrench clicked, yet you went further after the click. Is this a standard practice in building a VW engine? My other question was the head studs were not installed during the assembly of the case halves. Are you installing them after the case is torqued? I would be worried during installation of the head studs might push any metal chips through the inside of the engine. Is that something not to be overly concerned about, or am I over thinking things? Thank you.
@FixinBugsNStuff4 жыл бұрын
Great video! CT I thought you were going to lose a finger when the 2 halves went together. 😂. Oh you guys decided to get ac after I visit. I see how it is. No worries 😉. One day I will come down to build my Super 1600 with Darrin and hopefully you. Take care guys!
@vwdarrin4 жыл бұрын
HAHA! Thanks man!
@andyparker5224 жыл бұрын
Great Video!
@vwdarrin4 жыл бұрын
Thanks Andy!
@caduceus334 жыл бұрын
What a nice, clean, and organised set-up you have here, looks great!
@terryprevatt4 жыл бұрын
Great info. Thanks Darrin and CT.
@vwdarrin4 жыл бұрын
Thanks Terry!
@jimcatanzaro78082 жыл бұрын
I was never into VW always into Chevys cheap power But these guys seem nice and light to work on
@1970chevelle3964 жыл бұрын
I have one of those same kind of A/C's in my office. There cheap to run compared to the central A/C.
@brianhanel68972 жыл бұрын
I've always used gasket sench you know the one with the girl on the can and the dauber on the cap never had any leaks or any problems getting the case apart later great stuf
@scottalvey17873 жыл бұрын
Darrin, I’m interested.
@vintage76vipergreenBeetle4 жыл бұрын
Great info guys. 👍
@vwdarrin4 жыл бұрын
Thanks man!
@onehappykombi2 жыл бұрын
Mike Fn Garage recommended me your channel. Subscribed!
@alikatate23502 жыл бұрын
Oh yeah Great video for someone who knows very little!! I subscribed 🤙🏼
@banugobanviddunusamy74963 жыл бұрын
Hallow Mr.machaniker your work and your Workshop Are very cleaning......Amazing sir.....
@OwhyeeVdub3 ай бұрын
That's a serious lift.
@mikehammer45464 жыл бұрын
Darrin, have you ever thought about doing a 40 hp with big bore kit and 1600 rocker? I hear its a good set up for single port stockish motors.
@jonlaws44934 жыл бұрын
Please, please, please show how you set rocker geometry for this motor! Thanks Darrin
@wtbm1234 жыл бұрын
Cool good video
@vwdarrin4 жыл бұрын
Thanks!
@youwantshum98603 жыл бұрын
I usually cut a 45 degree tip on gasket maker tubes, comes out more evenly/quicker.
@hdscarmax-dx2fo4 жыл бұрын
Sweet video
@stevewesley81872 жыл бұрын
VALCO makes a squeezer for small silicone tubes that works great .
@Doubleodude3 жыл бұрын
I get ten points because I saw you put the cam plug in backwards and then smoothly switch it. LOL
@low-fi11033 жыл бұрын
Im just watching this like "cha-ching"..huge money to build motors like this..I have a very similar built 2110 and it was about 7k from case to carbs.
@leehuntley1892 жыл бұрын
Darrin have you tried applying sealant with acid brush I've had great results with acid brush
@dalejrfan8200020004 жыл бұрын
There is a gentleman in Strasburg Ohio. That builds VW engines.I will try to get his number.
@dalejrfan8200020004 жыл бұрын
@Joseph Andrade ?
@cigarcaptain4 жыл бұрын
great stuff D
@mastermatt2894 жыл бұрын
Great video learn so much just watching and listening to you talk and build. Question do you set static compression on big cam motors or do you set it to dynamic compression.
@aebrahim49623 жыл бұрын
Hi, Thanks for posting your builds- helps for first timers . To enquire, is loctite high temp silicone any good for sealing the cases?
@slimjim1194 жыл бұрын
It's great to see u dude great video
@vwdarrin4 жыл бұрын
Thanks Jim!
@hussianmohmmad46133 жыл бұрын
😍ilike to pieces main bearing… but did you put 2 pins in to side of case (main bearing dwal pin
@Omar-Type27123 күн бұрын
Great vid. Very informative. Where are the other parts.
@seventhson278 ай бұрын
If you don't get those dowel pins in the main bearings lined up just right, the motor will run about 10 miles, then suffer an "unscheduled disassembly"
@MrsPenPal4 жыл бұрын
Gifted hands
@TheDarthSoldier3 жыл бұрын
Definitely looking for a new motor for my beetle, gotta tear apart the old one. Sat for a couple years and when I got it started again, oil and smoke were coming out the exhaust. Definitely like your stuff. What do you charge to do a build like that?
@jeanlawson913310 ай бұрын
Yep... AIN'T IT JUST AIN'T IT 😎
@TimsWorkshopTJY4 жыл бұрын
Hi Darrin, Have you ever rebuilt a flat 6 on a 911 or like on a corvair? It would be a cool video to see
@rheidtech4 жыл бұрын
Dont forget the orings for the coolant passages😲
@throttlebottle59064 жыл бұрын
lol
@GarageTimeAutoResto4 жыл бұрын
What do you use in the cylinder base gaskets
@frankmcnab5223 жыл бұрын
I've got a 1970 karman ghia
@MrVwgigalow4 жыл бұрын
MST valve covers for a buggy not so much for street car there shape makes it impossible to fit between the body
@dalejrfan8200020004 жыл бұрын
Hopefully this helps you out.
@frankcamper73182 жыл бұрын
Darrin, I believe the 13mm huts torque down to 14 ftlbs from the 40horse on up, not 18 ftlbs -- unless you mean 18 just for the aluminum cases?
@VWWRENCHIE4 жыл бұрын
I still miss Tite Seal.
@mastermatt2894 жыл бұрын
Hey what is your professional opinion on the K style thick wall 92 barrels. 92 at the case and 94 at the head
@briansteinc4 жыл бұрын
Nice video. I like the engine build shop and the neatness of the parts layout. Just curious Darren what county do you live in. I'm over in polk county southwest of Disney.
@harryloibl51832 жыл бұрын
Hay Darren what’s your thoughts about a stroker 82 in a stock mag case thanks buddy
@michaelfiaschetti7722 жыл бұрын
What would you recommend for 1958 beetle type 1 sedan, to beef it up a little? Thanks Mike Fiaschetti
@mrvolkswagen33623 жыл бұрын
82 x 90.5...why not bigger if you are using bubble top...just bought one looking for a stout combo..suggestions??
@ryaneide17012 жыл бұрын
Hey Darrin. Doing a similar 2110 build. What cam do you recommend with Panchito 044's or Empi GTV's and 48 IDF's!!!
@mehmetturanozturk7 ай бұрын
Hello, my name is Mehmet Turan Öztürk, i live in Istanbul Sarıyer Türkiye and i watch your videos with interest and appreciation, i am not an automobile or engine mechanic, but as far as i know from my sincere friends who do this job, they use classical gaskets in engine blocks, but you use liquid gasket, doesn't this cause any problems in the future? Thank you and wish you happy days.
@ocavant2 жыл бұрын
Where did you source those sealing nuts for the main studs?
@harveycruz24093 жыл бұрын
Hello darrin, in this video I notice that you only put the o rings of the case in only 4 studs and not in the middle, I have an aluminum case and the person put the 6 o rings, right now my motor has a leak in the studs in the middle of the lower part, I ask, only the o rings go in the corners, thanks,
@vintage76vipergreenBeetle4 жыл бұрын
The type 4 valves guides info. Ask Ray on thesamba.com or shoptalkforums.com where to get oversize guides.
@dougpolansky60014 жыл бұрын
I am interested in an engine like this one! Don’t have to have such RAD heads though. I have tried emailing you several times but it gets kicked back as undeliverable. Do you have a website? Great videos.
@robertm21723 жыл бұрын
So I’m a old vw guy I am from the 90s I’m a modern day guy that’s plays with supercharged cars but I still own a 65 Convertible VW beetle that I bought 22 years ago and now. The cars going to paint soon as because I need my beach cruiser back. So the question is way back I bought a Fuel injection block with no provision for a fuel pump is this a better block to build a More reliable motor?
@shoominati237 ай бұрын
I miss your videos Darrin, I wish you would do more regularly.. Anyway, I was thinking about a 2180 build, with a 82mm stroke - do I need to have the camshaft relieved or not? I wish things for engines werent as pricey, but I refuse to go to a watercooled ie a Subaru - its just not a VW no more plus the ground clearance ive seen with the sump riding so low is terrible! hope to se you soon bud
@misterbs-fixit16364 жыл бұрын
So wish I was closer. I’d be haunting you to build me an engine
@1fastbuggy5024 жыл бұрын
Darrin. Do you do ant oil modifications to a high H.P engine cases ?
@Kanrinin017 ай бұрын
What is this gasket joint? aren't you support to put anerobic gasket here???
@aaronlarkins23163 жыл бұрын
been watching your vids and have stock motor that i wan more out of for daily summer driver seeing its Illinois. need help
@zundfolge14322 жыл бұрын
I have heard that if I build a 2110 and put it in a swing axle trans that it will strip 3rd and 4th gear is this true?
@capthwdy084 жыл бұрын
How much will the used 1600 be and will it be a super 1600?
@oldtanker48603 жыл бұрын
I want a Karmen Ghia too... :( RE that engine you were building what kind of price (ballpark) is it? For a slightly more than stock engine (say 60 to 70 HP vs 40) what do you recommend?
@jaimemartinez59342 жыл бұрын
I'm doing a rebuild on a 1600 . I want a little more power nothing crazy just a little. Make it sound beefy What do u recommend?
@Krasimir_BG3 жыл бұрын
When are you going to post Part 2
@jankasdetailing4066 Жыл бұрын
Do you know det ring size on 90,5mm piston? 1,5x2x4 or 2x2x4?
@dougfreet2670 Жыл бұрын
Are you still looking for seats for your 66 low back seats : I have a pair