Excellent video and instructions. Sending a link to my son so he can fix his Arosa. I like the fact that you protected the driveway from getting dirty.
@jeroenpeters61154 жыл бұрын
Hi, did you only replace the grease in existing joint? (and the rubber housing)
@joolsonthetools5 жыл бұрын
Great video! Such a simple method with the pliers for tightening the clips too. The “special” tool is very expensive 👍
@crisspyro4588 жыл бұрын
nice tutorial. more lupo tutor's ... :) i have 1 too verry helpful. tkx
@bobic197319 жыл бұрын
jestes dobry w tym co robisz. pozdro
@MultifunctionKaTech4 жыл бұрын
Good vídeo thanks for sharing.
@CANERm38 жыл бұрын
Dont buy Aftermarket one buy only OEM original vw part i had very bad experience with Aftermarket one ripped only 1year another split in 2 pieces before splitting half it leaked grease , after that i fitted original vw Part after 2 years its still fine and leakfree
@manochico5258 жыл бұрын
thank you so mych!!!
@Kieran461005 жыл бұрын
really super demo. great help, thanks a million
@leej83947 жыл бұрын
Thanks for the video, very good and great instructions.
@tomaszwegrzynek23953 жыл бұрын
Thank you
@hatimelias74656 жыл бұрын
Great.. thank you very much
@foxdark51654 жыл бұрын
best job
@abood0044 жыл бұрын
thanks
@markbulley11796 жыл бұрын
Advice from attempt. Buy a CV joint remover tool rather than hammer off, less risk of damaging the CV joint and you may actually get it off!
@burokakaroki36037 жыл бұрын
Thanks!
@thisname1is1sukzable3 жыл бұрын
thankyou!!! exactly the car i needed to fix too.
@KiranParmar885 жыл бұрын
Great vid! What's the three lower arm bolt size?
@FixYOURride135 жыл бұрын
Hi, if I good remember that wos 13mm
@KiranParmar885 жыл бұрын
@@FixYOURride13 fab, thank you!
@tubedujacques3 жыл бұрын
similar as skoda felicia 1999????? great instruction
@FixYOURride133 жыл бұрын
Hi, true, similar like all vw group 😉
@mihaichelmus4 жыл бұрын
Nice tutorial, this video will save me £50. You put a new nut at end? Or is the old one?
@FixYOURride134 жыл бұрын
Hi, thanks 👍, if I'm good remember I use the new one, was in cv joint kit.
@josephweston66286 жыл бұрын
I’m really struggling to get the hub off once the centre nut is removed. Any ideas?
@FixYOURride136 жыл бұрын
Joseph Weston hi, us rust penetrator and hamer watch out for the thread .
@aof5prandom9396 жыл бұрын
do you know how to replace the trunk door lock? If you do could you make a tutorial... For the Vw lupo
@FixYOURride136 жыл бұрын
Hi, No we don't have , sorry
@samiralim958 жыл бұрын
nice video👍✌
@markbulley11796 жыл бұрын
Good vid. Can you tell me the size of the centre nut? Mine is 30mm so guessing up to 35mm. Is working off one axle stand cool? Seems okay.
@FixYOURride136 жыл бұрын
PHIXER hi the red one had 30mm but don't be surprised if yours be different.
@markbulley11796 жыл бұрын
Certainly is, my 30mm doesn’t fit :( My local halfords goes up to 32mm and even that doesn’t fit.
@FixYOURride136 жыл бұрын
PHIXER hi, check the nut you have 6 point or 12 point nut because the socket must be the same tape 6 or 12 points.
@markbulley11796 жыл бұрын
It is a 12 point spline and can confirm a 36mm socket is needed for Polo 9N3. I attempted to do today but was delayed by getting the CV joint off, taking to garage. Lord knows how you got yours off in a few taps.