Lets Install Those No Name Chinese IDF Clone Carbs on my Volkswagen! Big Fail? Part 2/2

  Рет қаралды 38,256

VWJAWBREAKER

VWJAWBREAKER

Күн бұрын

Пікірлер: 248
@tommiesmith3369
@tommiesmith3369 3 жыл бұрын
It’s all about jetting that’s it. Those could be great for your setup. I don’t think valve size is a gauge to work with - of course it is but reality says you can get many varieties of setups functioning on the same valve size . It all goes back to where do you want your power band . A large venturie will be soggy on the bottom end and awesome in the higher rpm range . And vise versa for a smaller vent . The venturie effect is squeezing the air through an opening where it speeds up on the other side - this aids in port velocity for lower rpms and also vacuum to pull fuel out of the bowl. But can become a choke at higher rpms. On a big vent you loose all sorts of port velocity on the bottom end but gain the loss of a “choke” on the top end so it flows and flows. All about drive habits and just what you want to achieve. IDAs can be the best of both worlds if setup correctly. 44s with 36vents is a strong all around setup . I ran 44s with 32vents for ever such a good setup for my little motor . I think the board with flow is not functional if the information is not consistent when comparing . I also think carbs are easy - need to do a video of what is what and why things are happening when they happen.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Well said sir! That’s pretty much what happened, large vent on this setup absolutely flew mid through upper rpm band but was soggy down below. Of course I needed to up the idle and main jets some more. However, I don’t race this car and street drivability is important for me. I ended up putting my 44’s back on for now. I know it could be better than what it is but all around it’s great how it is. I figured I’d see how these perform and for the price I couldn’t go wrong. IDA’s with 36 vents would be perfect but then I’d be out cnc machined intakes 🤷‍♂️ Sometimes it’s just best to leave things alone but then that’s no fun 😂
@GoodOldMike
@GoodOldMike 3 жыл бұрын
That jam at 11:56 is pretty dope. 😀 Still watching and curious how this is going to work out.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I have to agree, not to mention the dudes music in general is killer. Need more tunes! It worked out ok if I would have remembered what size intake valves I had when ordering the carbs. The venturi is too close to the intake valve size so I lose low end and it idles higher than I would like. Top end is no joke! Need smaller venturi for these carbs and it’ll be perfect. But that’s a story for later down the road.
@zas5892
@zas5892 2 жыл бұрын
Both of my 48 setups on both of my Motors are totally streetable they idle perfect at 9:50 and there are 9 1/2 10 1/2 to one motor and they are all day all night on the street no problem Gary put the carburetors back on they'll work
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Yes they would work however I had some reasons why I went back to the 44’s. Appreciate the input 👍
@zas5892
@zas5892 2 жыл бұрын
Right on maybe on the next big motor
@dillyd3488
@dillyd3488 3 жыл бұрын
Bare feet wrenchin'....Now THAT's how ya do it!
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Barefoot when it’s safe to do so... that’s life in the south 😂
@jaytee1086
@jaytee1086 3 ай бұрын
I put a 1915cc at 11:1 with heads i ported just as massively in to a Manx buggy that weighed 1100lbs. .lol......i even polished the exhaust ports and the header pipes.(I even polished the collector and u-bend). So i fabricated a manifold for a Holley 350 cfm 2 barrel carb for simplicity....after adding a carb spacer it worked amazing with proper jetting. (And yes i had to create a custom throttle cable). But that's what we do for the love of our toys....lol
@VWJawbreaker
@VWJawbreaker 3 ай бұрын
Sounds like it was a blast!
@jaytee1086
@jaytee1086 3 ай бұрын
@@VWJawbreaker Yeah it was I had to sell it after all.,,...but it was a blast for the time I had it. . But I sold it for a pretty penny. $27k...
@VWJawbreaker
@VWJawbreaker 3 ай бұрын
@@jaytee1086 nice!!
@Opalsdad
@Opalsdad 2 жыл бұрын
Brand new here… very first video I stumbled across, to be honest I wasn’t feeling it at all, But I saw that you were working BAREFOOT 🦶, this is when I knew I found the right channel!
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Appreciate your comment and honesty. It’s really difficult to be entertaining and try to provide knowledge at the same time. Especially since I’m not a know it all, I just share my experiences, thoughts and what not. Thanks for being here 🤙
@alec1451
@alec1451 5 ай бұрын
I have found myself grinding and welding in flip flops before lol
@VWJawbreaker
@VWJawbreaker 5 ай бұрын
Sometimes it happens… I try to always be safe but we know how it goes 😂
@kevinvincent4323
@kevinvincent4323 8 ай бұрын
I installed. Type 4 motor in my 72 beetle. I like the removable deck lid idea. I made my rear apron removable. Otherwise I have to do serious disassembly just to get the motor out.
@VWJawbreaker
@VWJawbreaker 8 ай бұрын
A removable apron is a great idea!
@bernardstander7642
@bernardstander7642 3 жыл бұрын
Lol, your neighbors must love you like mine love me!!! Also running a stinger on Daisy and trumpets on the Baja!!!
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Nice!! Luckily my neighbors don’t hate me too much as I do my beat to keep it down in the evenings and early mornings.
@boydchapman5660
@boydchapman5660 3 жыл бұрын
I am just getting into vw beetle cars. I am learning g alot from your channel. I love your channel, no fluff just getting it done! Keep up the great work.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thank you sir, I appreciate the feedback. Check out some of the other great channels in my video description. Remember, I’m not an expert, just a VW guy doing his thing and recording my experiences. Others know way more than I do but together as a community we are stronger.
@jahmahrahdesafilli6268
@jahmahrahdesafilli6268 Жыл бұрын
Just to say thanks for the video. I pulled a lot of very useful information from Your work here. In fact I bought 2 of these for My volvo 740 project but I could only fit one on because they are too tall to go under the wedge bonnet "duh" anyway like You I'm always learning from My mistakes. Best of luck with Your cars. Best Wishes Jahmahrah
@VWJawbreaker
@VWJawbreaker Жыл бұрын
I appreciate the kind and thank you for taking the time to comment. We all learn from one another, no matter if some want to admit it or not. No one knows it all so the more we can share what works for each other, the better we can all be. Glad the video was able to help you out! Happy New Year.
@jahmahrahdesafilli6268
@jahmahrahdesafilli6268 Жыл бұрын
@@VWJawbreaker Oh I forgot to say for tuning the mixture I always use a little device called a Gunstons Colour Tune. It's a clear spark plug that allows You to see the actual colour of the explosion, and You then make adjustments to get a nice blue burn. I've had mine since the 70's and have always tuned My engines with one : - )
@VWJawbreaker
@VWJawbreaker Жыл бұрын
@@jahmahrahdesafilli6268 that sounds like a cool concept tool!
@vintagespeedvw7864
@vintagespeedvw7864 3 жыл бұрын
You’ll get it figured out. We all sit back and ponder on these cars! Good video.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
If I would have remembered that my intake valves are 42mm and not 44mm when I ordered the carbs we would have had a different outcome. Ran great mid and upper rpm, lost low end torque due to the venturi being too large. Live and learn lol
@umarghazali631
@umarghazali631 2 жыл бұрын
Hello Sir, I really Enjoy watching all of your video. Especially on the Tricks and tips stuff. Im having trouble on tuning weber Progresif 32/36 . I hope you will post one from your video. Thank you!! Keep Up the good Work sir!
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Thank you sir, I’m glad you enjoy the videos. I do not have a video on the progressive carb and currently don’t have plans on putting one out. Maybe one day but I’m not sure who has my progressive carb that I lent out.
@Fastvw1
@Fastvw1 3 жыл бұрын
Grass hopper has much to learn about intake manifolds and heads but good job on the basic's. Oh need to do some more home work on IDA's they come with 37 venturis
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
For some reason I thought I had larger intake valves when I ordered the carbs. I know the IDA’s have smaller venturis but these are IDF’s to keep the intakes the same.
@jnwhrt13
@jnwhrt13 2 жыл бұрын
Sounded good revving it up - what’s the engine size or is it really the matter of those hoggin heads needing the extra - could you have upgraded the venturis and jets to achieve a better outcome ?
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
It’s a pretty stout 2054 with fk8 cam, 1.4 rockers, 10.0:1 compression. I could have put smaller venturis in it and gone from there on the rejet, decided to put the 44’s back on since I do so much driving. I could have gotten these to work decided not to.
@Robc509
@Robc509 3 жыл бұрын
Thanks for looking at these carbs and taking us along. it has been educational. I've not got into these kinds of mods yet on my vws and will be sure to look back here and follow your set up guide. Appreciate it 👍
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thanks for being here Rob, I’m glad you found the video useful even if it’s for a later date.
@Spidious
@Spidious 2 жыл бұрын
Thanks you for the quick pin release. It's so much easier to get to the carbs to adjust them.
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
It’s such a simple thing to do that makes life so easy!
@DasLuftVolks
@DasLuftVolks 3 жыл бұрын
FYI stock Weber 48 IDA come from the factory with a 37mm venturi.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
That’s good to know for the IDA’s. These are IDF carbs since I already had the IDF intakes and linkage.
@AlanDavid1955
@AlanDavid1955 3 жыл бұрын
Hey Gary I stopped in Daytona Beach today at a place called Daytona Aircooled Parts he repairs Vw’s and Dune buggies , he said in 2 weeks he’s having a VW gathering at his shop and some companies that sell aftermarket parts for your VW will be there , I’m going , I thought I would let you know ! Alan first day of bike week was great. !
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Awesome man, enjoy bike week! I should be at Charlie’s show in a few weeks, hope to see you there.
@AlanDavid1955
@AlanDavid1955 3 жыл бұрын
@@VWJawbreaker great see you there
@travis67vw
@travis67vw 3 ай бұрын
How well does that centerpull linkage work with idfs?
@VWJawbreaker
@VWJawbreaker 3 ай бұрын
@@travis67vw works better than a regular hex bar imo! Over 4 years without issue on this CSP linkage.
@michaeltetzner5847
@michaeltetzner5847 5 ай бұрын
Hi, Gary, have been watching your videos on youtube for quiet a while now.. Very informative ! I am in the process of building a 1835 engine for my '73 beetle. Have the engine ready so far, and just pulled the old engine, to transfer all the cooling tins and other bits and pieces. Tried to do a mock up with the new manifolds and carbs, and there is a lot of interference between the manifold flange and the cooling tin. So much, that it is pretty much impossible to get the manifold in. How did you modify the cooling tins to make that possible ? Any tips would be greatly appreciated !
@VWJawbreaker
@VWJawbreaker 5 ай бұрын
Glad some of the videos have helped ya out! As far as the head tins, you’ll most likely need to modify them a little at a time to get the manifolds to fit. Usually you’ll modify the interior “flap” that goes between the spark plus. You might be able to bend things around a little to get the manifolds to sit properly.
@Mtbeaver9
@Mtbeaver9 Жыл бұрын
I have a question why we don't use f2 emulsion tubes in vw? what does the emulsion tube do?
@VWJawbreaker
@VWJawbreaker Жыл бұрын
That can be a long answer but the short of it is, the emulsion tube is used to maintain the air fuel ratio at all speeds.It consists of a well with main metering jet at its bottom. The jet has holes on its sides.It is in communication with atmospheric air. Initially air is drawn through the holes into the well and fuel is emulsified.
@chicagomike6666
@chicagomike6666 2 жыл бұрын
also--where did you relocate your coil..?? Mine is high up on shroud and always in the way...currently running Pertronix II and bosch coil...
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Coil with that cross bar linkage was between the fuel pump and fan shroud.
@jimlester5003
@jimlester5003 3 жыл бұрын
Sweet video Gary. Gives us food for thought! Thank you. Love the website too! Jim
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
We love and learn, here are some good examples in this video. Thanks for always being here Jim, have a great week!
@doglao1236
@doglao1236 Жыл бұрын
in brazilian race car vw bug called FUSCA Divisão 3 with 1600cc engine and weber IDA 48 140WHP, nice to see the race. Nice Job, I just rebuild another engine with weber 40 idf.
@VWJawbreaker
@VWJawbreaker Жыл бұрын
That’s some good hp out of a 1600!
@kenshelhamer9816
@kenshelhamer9816 3 жыл бұрын
I think your vacuum signal is lower with the bigger venturies and you need bigger idle jets.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Yea sir, you are correct. Still with the bigger idle jets it won’t idle well.... best to drop venturi size and rejet.
@Slick56
@Slick56 3 жыл бұрын
Ahh Dual Carbs... as soon as you said 48's I thought about port velocity and jetting. Some one should be able to supply you with vents or have a shop spin some out on a lathe. likely you will need to jet up on the main and drop the air a little. You can get bigger vents for your 44's or have your current vents bored out to say 38mm you will need to bump up the main and drop the air jets some as well. Idle jets may need a bump up too if you cant get it to adjust with the mixture screws. CB has that update kit for the IDF'S that changes the secondary vent to a spray bar and it comes with new vents and jets. but that kit would kill your bottom end too. I found stock idf44mm carbs on the street are just right for me. I run very similar engine to yours. A set of CB ultra wedge ports with bigger intake valves would do the trick too. I have a sweet set of gene berg 52's that I would love to run but would have the same issue as you right now. manifolds linkage vent size ect. Sad to say for me the next step is fuel injection or turbo or both to get more power and keep drivability with out tearing my motor down. thanks for sharing I am also not an expert but enjoy and appreciate what you are doing.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Like you, I’m not an expert. I’m just trying new things and bringing everyone along for the ride. You are correct, the vents are too big to idle and for low end. She screams hard up top though but not very streetable imo. I did find a set of smaller vents for these carbs, that’ll be a project for another time down the road. Thanks for the feedback, hope you have a great week.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Oh and ps, for some reason I thought my heads had 44mm valves, not 42’s. If that’s the case these would have worked better.
@haskyb9184
@haskyb9184 3 жыл бұрын
Interesting video, Gary. I like and respect that even though it didn’t work out you still uploaded. Didn’t even realise there was such thing as a 48 IDF. Another good less in carbs right there! Ben 🇬🇧
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
The reason they didn’t work out is that I was thinking the intake valve was bigger than it was.... if I would have remembered that when I ordered them things would have been different. It ran great mid and upper rpm, just lost low end torque. With that being said, I’m not an expert and we all learn together. Thanks for being here Ben.
@taxiarchisk.6031
@taxiarchisk.6031 Жыл бұрын
hi the point is that you need a race machine to put these chinese carburators otherwice you need to rejet them... to work ok .tell me what is your opion about the most suitable extra carburator for a Volkswagen Beetle. a single 40 type Weber .a Pict- 3 39....or type Weber 32/34......thank you
@VWJawbreaker
@VWJawbreaker Жыл бұрын
Actually that’s not true at all and this engine is no where near stock. They were better accordingly but the venturies were too big. Personally, I don’t like running single IDF’s or the 32/34 carbs. I would need a lot more info before I could recommend a carb.
@christianarocho4886
@christianarocho4886 3 жыл бұрын
Hello Sr. Can you provide me how to look up the carbs in ebay?
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
If you’re looking for IDF carbs, type in IDF Carbs.
@ChipsAndSparksGarage
@ChipsAndSparksGarage 3 жыл бұрын
It will work, just not today.. Great idea, on the removable hinge pins!👍
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
It ran and ran well above normal rpm idle range. I lost low end due to the venturi size, change them for one size smaller and it’ll be just fine. I thought my heads had the next size larger intake valve when I ordered them.... ops lol It would have worked fine if it wasn’t for that.
@doginu
@doginu 3 жыл бұрын
You needed larger main jets at least 2 sizes, the F11 emulsion tubes leaned it out even more. Just buy some 40 mm Venturis/Chokes for your Webers
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Those had 40mm vents in them. It all worked out in the end.
@thisisschennss8291
@thisisschennss8291 Жыл бұрын
Hi i want to know, after 2 years how reliable this carbs? And do you make a mod of the carb to make it reliable?
@VWJawbreaker
@VWJawbreaker Жыл бұрын
I didn’t want to buy a set of vents for the 48’s so I put my 44’s back on. I’ve setup a few sets for friends and helped them tune them in. I’ve only had an issue with 1 carb so far. It’s all in the prep and bench cleaning and setup.
@oversplodegarage41
@oversplodegarage41 3 жыл бұрын
Great video! You are not lying about those ports. Way bigger than stock. Hate it didn’t work out for ya at this time. Sounded good and mean though!
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Those ports and heads are huge man! I thought for some reason the intake valve was the next size larger than what I do have, if that was the case they would have worked perfect. They did work and run well, just idling higher than I wanted and lost some low end torque.
@KCPurpleBug
@KCPurpleBug 3 жыл бұрын
Love it may have to look in to some deferent carb and I like the quick change on the hood
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thanks Jim, appreciate you being here.
@2GuysandaBug
@2GuysandaBug 3 жыл бұрын
So many things to account for. Thanks for sharing, learned something new today.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Glad you learned something new. Even though they didn’t work out as planned, we all something learned together.
@eugenebaroni1298
@eugenebaroni1298 3 жыл бұрын
Great video man. Stay safe out there...
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thank you sir. Stay safe and have a great week.
@davidryan573
@davidryan573 3 жыл бұрын
Good parts is good parts, leave them on the shelf for the Frankenbeetle, when I would come into good deals I would pick it up, motivation to finish the project.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Excellent point David, that’s what I’ve been doing for the franken beetle build!
@braunshock6112
@braunshock6112 3 жыл бұрын
Keep up the great work, it's all about taking the knocks and coming back better..... I've bought a set of the 40s and just trying to work out whether or not to port and polish the stock heads or get new ones.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
As I always say, I’m not an expert. I made a mistake by thinking I had larger intake valves than I did, that’s why they didn’t run well in low rpm’s. Mid and high rpm’s it pulled like a beast and needed way bigger main jets.
@adammiller6606
@adammiller6606 2 жыл бұрын
That’s the way it goes sometimes. You’ll get er. ☮️
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Thanks 🙏
@scottalvey1787
@scottalvey1787 2 жыл бұрын
Can you go over how to install your electric fuel pump?
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
I can try to get a video done in the near future.
@vza423
@vza423 3 жыл бұрын
Thanks for posting.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thanks for being here.
@OFFAxisBuilds
@OFFAxisBuilds 3 жыл бұрын
Nice explanation and great video
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thanks man!
@mcdanielsmotorwerks423
@mcdanielsmotorwerks423 3 жыл бұрын
Thank you for showing these off to the community, I'm sorry the carbs didn't work out for you, I know that you have to pick your battles on what upgrades you want to make work. I had the same issue with 48 IDA's prior to installing 37mm Venturi. The way the 48 IDF's were out of the box you would have needed at least a 70 idle jets, and with the large Venturi and FK8 cam your idle might have settled in around 1200'ish RPM this is fine and well for the strip but is just not particle for a driven street car.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
100% correct, this would have been perfect for the strip but not practical on the street. They did great on mind and upper rpm, just no low end torque and some drivability was lost. We live and learn, we wanted to see what would happen and now we know.
@SladesVWBeetle
@SladesVWBeetle 3 жыл бұрын
Honestly they sound pretty nice brother! I know you’ll get it figured out for sure. Sounds nice reving up!’
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thanks brother! Everyone learns something new all of the time.
@SladesVWBeetle
@SladesVWBeetle 3 жыл бұрын
@@VWJawbreaker Absolutely, it’s all part of the journey.
@douglasbarnhart3324
@douglasbarnhart3324 3 жыл бұрын
Thanks for sharing.😁😁
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thank you for watching!
@MarkLoves2Fly
@MarkLoves2Fly 2 жыл бұрын
I like the deck lid idea. I don't remove mine enough to justify it myself, but props to you!
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Appreciate it, although I can’t take credit for it since I saw it somewhere years before.
@69mag
@69mag Жыл бұрын
Yeah, if that's all you took out of this video it was a win! Doing the dual 40 IDFs on my 68 Westy right now, taking some more classes at KZbin University😊
@VWJawbreaker
@VWJawbreaker Жыл бұрын
I’m sure between all of the other great videos out there, you’ll get yours dialed in.
@69mag
@69mag Жыл бұрын
@@VWJawbreaker Between you and EZGZ I'm picking up a lot more VW know how. This is my third VW to go through, I've got an 87 Syncro and am the caretaker of my sisters 72 Super Beetle (Formula Vee)
@VWJawbreaker
@VWJawbreaker Жыл бұрын
@@69mag the fact you compare me with EzGz, I appreciate that. We all have our way of doing things. My videos may not be suited for everyone so I try to direct people to other channels. It’s all about keeping these classics on the road.
@Jayvans_Super
@Jayvans_Super 3 жыл бұрын
I love that linkage
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
You got that right, the best investment yet!
@victormuro1
@victormuro1 3 жыл бұрын
Tks for the content !!! It helped me a lot here. I bought one of this as well but mine is a twin "Weber" 40. I would like to see how u install the drives for the gas pedal. How can I have photos or something of that? Thank u a lot. Cheers
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I’m glad the video has helped you! Are you talking about the linkage for the carbs?
@victormuro1
@victormuro1 3 жыл бұрын
@@VWJawbreaker exactly. Sorry I'm from Brazil so I was looking for the right expression for that part!! kkkkk
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@victormuro1 I don’t think I have any videos on the linkage.
@victormuro1
@victormuro1 3 жыл бұрын
@@VWJawbreaker tks...when you install it u had to change the stock linkage ? I mean it was easy to install ? Tks again.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@victormuro1 you’ll need linkage for dual carb setup. The stock throttle cable coming through the fan shroud will hook to the dual carb linkage.
@michaelbarnes7086
@michaelbarnes7086 3 жыл бұрын
Gary, scott barnes here in Virginia. Hey have you ever used the empi electronic ignition that goes in the Bosch 009 distributor? Pertronics is 150 to 180 verses 45.00. Just wondering if their reliable. Thanks buddy. Again love your videos.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Hey Scott! I haven’t used the empi electronic ignition yet. I know a few people who have and it’s been hit or miss. What I did, because of the price of the Pertronix and my cheap 009 copy had slop in the distributor shaft, I spent a total of $199 and went for the CB Magnaspark kit and haven’t looked back.
@type3666
@type3666 2 жыл бұрын
Nice Bug ;))
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Thanks!
@aarondavis5535
@aarondavis5535 3 жыл бұрын
hay did you get it running good where did you get those carbs from
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
There’s a part 1 to this video... they are from eBay.
@chicagomike6666
@chicagomike6666 2 жыл бұрын
nice video! I am running dual 40idf weber carbs--I think venturis are 28mm. My engine compartment is really cramped---some have suggested I cut "windows" or portholes into sides of engine compartment to let me tune them easier. Right now...its pretty damn hard to do anything...any thoughts on this. Will holes like this compromise rigidity---any other alternatives for adjustment and tuning?
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
I’m right there with you and with large hands it was about impossible to adjust the carbs and when I got a clogged idle jet, we’ll that was a nightmare. I ended up cutting windows in the sides so I can access everything much easier. Mine are removable so it minimizes dirt and what not from coming into the engine compartment. Do what works for you though as it’s your car.
@dmwgreywolf1123
@dmwgreywolf1123 3 жыл бұрын
You talked me out of getting those. Whew, that was close, I was getting close to what I thought would be an upgrade, but sure looks like nothing but a headache there. I'll retreat to "if it aint broke, dont fix it". lol Good looking out man!
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
They actually ran great, mid and upper rpm was great... My idle issue was due to me thinking my intake valve was bigger than it was so the larger venturi moved the power band further up.
@terryprevatt
@terryprevatt 3 жыл бұрын
They will work just fine once the Venturi is figured out. I run these in my bus with no issues.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@terryprevatt yea sir, I can drop down to a 38mm vent and they’ll be just fine.
@1fastbuggy502
@1fastbuggy502 3 жыл бұрын
Love that attitude ! GET TER DONE SON !
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
We all learn together!
@valdiviajr1
@valdiviajr1 3 жыл бұрын
Gracias homes 👍
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thank you 🙏
@modotvideo
@modotvideo 3 жыл бұрын
Thanks for sharing your Experience even though it didn’t totally rock
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
We all learn together, I’m no different.
@modotvideo
@modotvideo 3 жыл бұрын
@@VWJawbreaker yes indeed and thank you for sharing this. I will go back to watch the set up video again but u got these from Amazon right?
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@modotvideo I got these off of EBay due to them being cheaper.
@jasonsalsbury9191
@jasonsalsbury9191 3 жыл бұрын
As always great info and video.Do you find one style linkage better than another thinking about trying my hand a some China 40 idf but don't know what linkage set to go with.Thanks
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Thank you sir. I’ve had several different styles of cross bar linkage.... spend a little more and get a quality set from a quality company, it’ll save you so much time and effort in the long run. As for the center pull linkage like I have, the CSP linkage is the best imo.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Also, if you don’t already have dual carb setup, it might be cheaper and better to buy a full kit instead of piecing one together.
@jasonsalsbury9191
@jasonsalsbury9191 3 жыл бұрын
Good deal as always thanks for the info and time.
@Figment078
@Figment078 3 жыл бұрын
what kind of fuel hose are you running on there?
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
3/8” fuel injection hose from the local auto parts store.
@erisgh0sted961
@erisgh0sted961 Жыл бұрын
Those intakes make me think of Scarface. Also I thought you were checking for fuel leaks with a grill lighter. I was like 😯, all brass.
@VWJawbreaker
@VWJawbreaker Жыл бұрын
Lol, those ports are pretty big.
@robertsroberts4327
@robertsroberts4327 3 жыл бұрын
Can I send you my after market webber to go through? I cant get the thing to stop burning rich. Driving on it now for 2 yrs but keep fouling plugs.. I have a fuel pressure regulator installed.. 3 psi.. tried using vacuum guage to set, no go.. maybe I need to just order another carb from redline. Any ideas?
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I’d double check your accelerator adjustment and jets, wouldn’t hurt to double check the float. If you’re running that rich it’s probably one of those three.
@carguytroy
@carguytroy 3 жыл бұрын
What linkage is that you have? Looking for something along that line for my Ghia
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
That’s the CSP bell crank linkage. The best linkage I’ve ever used.
@carguytroy
@carguytroy 3 жыл бұрын
Right on. I’ll have to check that out. Thanks.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@carguytroy no problem. Have a great rest of the week.
@deanrobinson3717
@deanrobinson3717 3 жыл бұрын
They sounded awesome with the stinger, you will sort them, I’m sure if anyone can, you can !
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
They did sound good, it was a mistake on my end. I thought I had bigger intake valves than I did.... oh well, they make different venturis for them.
@richardbonn3882
@richardbonn3882 Жыл бұрын
Thanks BRO !
@VWJawbreaker
@VWJawbreaker Жыл бұрын
Absolutely 🤙
@michaelbarnes7086
@michaelbarnes7086 3 жыл бұрын
Just looked that magnaspark kit up. Man what a deal! Coil, wires and distributor complete. I have a 1641 engine with dual 40hpmx carbs and side winder ceramic exhaust. Will that distributor kit help with better startups and acceleration etc. What's your take on the 1641 engine. To be honest it runs like a hungry fat lady at a buffet. Sorry that was wrong. In a way. I should have went aa 88 pistons. Probably would have ran substantially stronger. Hey, thanks for responding pal.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
The nice thing is the Magnaspark is fully customizable and can grow with you as your needs or engine combo changes down the road. That setup does deliver more spark energy which will help with all around performance. I had a 1641 before I built this other engine. I wouldn’t recommend the slip in 88’s as the wall are too thin and the engine will run hotter. The machine in 88’s, well you mine as well machine for 90.5’s or 94’s at that point. Just some random thoughts for ya. Have a great rest of the weekend.
@philiphapeshis1226
@philiphapeshis1226 2 жыл бұрын
They are good carbs for the money.
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
As long as they are bench cleaned and set, you can’t beat them.
@jimlester5003
@jimlester5003 3 жыл бұрын
Gary, tech question for you. I'm installing the weber 34 ict duals on my trike. The tin are trapped between the manifolds and the head. Should I clearance the tins or do you think it will be okay? It's a single port. Thanks. I just needed some advice even though I may already have an answer. Have a great day! Jim
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Hey Jim! It would be wise to trim the head tin so the manifolds clear, if not you could end up with a vacuum leak.
@jimlester5003
@jimlester5003 3 жыл бұрын
Thanks for the voice of reason. Lol. I knew it but almost wanted to chance it. Fix it now in the garage instead of on the road. Thanks again Mr. Wizard.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@jimlester5003 not Mr wizard, just been there done that experience 😂
@johncollins5552
@johncollins5552 Жыл бұрын
The H40 pairs generally deliver better power across the rev range than the rest of aftermarket stock 1600 if anybody needs to know, dell ortos are also good but they're getting old now.
@johncollins5552
@johncollins5552 Жыл бұрын
Nice decklid mod, have you done an easy out rear apron mod, that's something I want to do this year just cos my apron is rusty anyway and might as well make life easier so I don't cut my knuckles every few years when I replace the exhaust! I hate that.
@VWJawbreaker
@VWJawbreaker Жыл бұрын
@@johncollins5552 I haven’t touched the apron yet, it’s something I’d do if I ever need to replace the apron but don’t want to hack it up just to make it removable.
@hussianmohmmad4613
@hussianmohmmad4613 3 жыл бұрын
All chine carb problems on needle flow tank
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Yeah I realized that, thanks for the reminder!
@hussianmohmmad4613
@hussianmohmmad4613 3 жыл бұрын
Nice job It can fix… .try it
@VeeDubP8
@VeeDubP8 3 жыл бұрын
Of course you have other vw projects... Those carbs could go that way... Just a thought... I have AS 40/35.5 heads (I think from CB performance) Feeding the fuel is dual 40mm Kadrons. They work, but my fuel mileage sucks. Any suggestions? Keep up the great work brother!!
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I wonder if you’d Milage is that bad if you’re running too rich? How black are the spark plugs?
@hussianmohmmad4613
@hussianmohmmad4613 3 жыл бұрын
Same happened with me Set flow
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Yea sir!
@hussianmohmmad4613
@hussianmohmmad4613 3 жыл бұрын
@@VWJawbreaker less fuel ⛽ dear
@hussianmohmmad4613
@hussianmohmmad4613 3 жыл бұрын
@@VWJawbreaker fuel ⛽ level inside carbs not correct
@volkswatson
@volkswatson 3 жыл бұрын
Yeah I'd like to gain more knowledge on carb inner workings - any suggestions?
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
The beat place to be honest, grab a Webber book. Bench setup is the most important, from there is jetting. Read whatever you can find.
@orbitaljellyfish808
@orbitaljellyfish808 3 жыл бұрын
You sound sorta like Mike Judge 👏👏
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Not sure if that’s a good thing or not…. Who’s he?
@mikebriere7531
@mikebriere7531 3 жыл бұрын
Sounded great when you were revving it up
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
The top end loved those carbs, I just lost some low end and idling.
@felixlafuente9714
@felixlafuente9714 Жыл бұрын
Try this: one, close all air bypass screws. Second, Fuel level up and third, smaller airjets will put you there. I bet
@VWJawbreaker
@VWJawbreaker Жыл бұрын
All air bypass screws are always shut on my carbs. They ran good but the venturis were too big causing a higher idle rpm to maintain a vacuum through the idle circuit. Air jets aren’t being utilized at idle, only at higher rpm.
@felixlafuente9714
@felixlafuente9714 Жыл бұрын
@@VWJawbreaker good day! thank you! Sorry, yes, you are right on idle! Do you think Bigger idle jets wont help it?
@VWJawbreaker
@VWJawbreaker Жыл бұрын
@@felixlafuente9714 no need to be sorry, we all have different strengths and weaknesses and we’re better as we all learn together! Larger idle jets would only deliver more fuel and make it run richer at idle. Refer back to the pinned comment on this video, Tommie did a great job going through some explanations.
@richpeacock5768
@richpeacock5768 3 жыл бұрын
Jawbreaker sounds a lot like Mellow Yellow when she is cold. I feel the need to do some adjustments on Mellow Yellow now because she is definitely not right.
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Maybe she just needs some more tweaking. Not running chokes is a sacrifice we make though.
@stephenbrown5580
@stephenbrown5580 3 жыл бұрын
Curious to see if these are a decent upgrade option in the end. Any thoughts on playing a bit more with them or an upcoming video in the foreseeable future? Love the channel, BTW
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Well, since I screwed up by ordering these with a bigger venturi, the low end performance was blah. I could have spent another $100 and bought smaller vents but decided to sell them instead. In all reality, and my driving habits, 44’s with 36 vents are a better choice. With that said I know a few people who have had great success with these carbs as long as you bench clean / set them up. If you need a dual carb kit, I’d recommend buying a kit instead of piecing it together.
@Bonis67
@Bonis67 3 жыл бұрын
What is IDF and IDA?
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
IDF and IDA are models of Weber carbs. Almost like saying 30 pic or 34 pic carb.
@Bonis67
@Bonis67 3 жыл бұрын
@@VWJawbreaker thanks I had no clue
@AirkooledKustoms
@AirkooledKustoms 3 жыл бұрын
keep on
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Won’t be on the same level as you guys, but I’ll never give up.
@zas5892
@zas5892 2 жыл бұрын
Those carbs will work on your car I've got a 2332 super flows with 46 mm valves in them and I'm running dual 48s and it's just jetting once you get the jetting and the chokes done it'll be perfect and those 48s will make those heads breathe I also got a 2496 I'm putting together for another manx and it's got dual 48s on it with 37 chokes the Venturi down in the middle of the carb and it's got huge jets in it you just need to put them back on and read Jet them they will work on the street if I'm running 48 idas with 46 mm valves you can run those 48 idfs with those 42 mm valves no problem more fuel more air come on Gary put them back on do it
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Yes it could be done but I don’t want to have to buy a different set of Venturi’s for it so I gifted them to someone.
@zas5892
@zas5892 2 жыл бұрын
Oh right on well cool well someone else will definitely enjoy those carburetors
@johnfreeman1189
@johnfreeman1189 3 жыл бұрын
" If one does not fail at times, then one has not challenged himself " Ferdinand Porsche 1875 - 1951
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Perfect quote of the day!! These did work well, they ran great I just didn’t do a ride along video. With the larger carbs and venturis, I lost some idle and low end but gained on the top end.
@johnfreeman1189
@johnfreeman1189 3 жыл бұрын
@@VWJawbreaker So.... Will we see a turbo next! Love the content. (0\_/0)
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@johnfreeman1189 it’s been an idea for a while now but I’d have to de tune the engine some. Plus I need they the 60 done first.
@hussianmohmmad4613
@hussianmohmmad4613 3 жыл бұрын
My plan supercharged 2276cc with maxican efi And Microsquirt ecu mangment 😍
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@hussianmohmmad4613 nice!!
@antoniopascualquelopanamon3980
@antoniopascualquelopanamon3980 Жыл бұрын
La esplicacion tiene que ser con el motor no con pizarra
@VWJawbreaker
@VWJawbreaker Жыл бұрын
Issue was the Venturi size vs the intake valve size.
@trevcessna1723
@trevcessna1723 3 жыл бұрын
Buy American 100% of the time and support your country! I pay up and will always use American made parts and if I can’t find what I need I buy European parts! I think we all need to rethink our choices! Car sounds great!!!! Thanks Bro!
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I don’t disagree with you one bit, just wanted to prove these no name cards are the same as the name brand carbs.
@battyboomfatty
@battyboomfatty 3 жыл бұрын
Like EMPI? Which are made in China now 😂
@trevcessna1723
@trevcessna1723 3 жыл бұрын
Yep you’re right, but if enough of us demand parts be made in North America.? We all need to collectively push for a higher moral standard from those rich company owners, they can afford to make less profit and create more jobs here! Besides I personally don’t want to support a communist country that pollutes the environment using sweat shop labour! Stay safe!😷
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@trevcessna1723 right there with ya man.... I’d rather pay more knowing that I’m supporting our country and having the parts made to a higher quality standard.
@PhilipQuinto
@PhilipQuinto 2 ай бұрын
I thought I was the only one that works barefoot
@VWJawbreaker
@VWJawbreaker 2 ай бұрын
Haha, Apparently not! 🤙😂
@sheldonjr7hp
@sheldonjr7hp 3 жыл бұрын
I did the math. The 48’s are gonna be a tick small but I think they would go good on my stock cam 1641 with 041 heads from JC Whitney ha ha. 😎
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
You know Randy, you may want to go with 51’s for that setup 😂😂
@sheldonjr7hp
@sheldonjr7hp 3 жыл бұрын
@@VWJawbreaker I don’t want the front wheels to come too far off the ground. 🤪I just want stop light to stop light acceleration. And if you knew where I live you’d understand how silly that sounds. I live in Moody County. There are no stoplights in the entire county. There is no McDonalds in the whole County. We do have a subway and a Dollar General Ha ha. Oh we are up to 3 four way stops. That really confuses people. I mean who really is supposed to go first. No you go we all trying to be nice. On that rambling note I better get back to work ha ha. 1641 is getting a centermount Dellorto ‘DRLA40 with 30 mm Venturis. And I’m gonna like it cause that what I got 🙀😎
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
@@sheldonjr7hp oh man, every time we talk I get even more jealous of where you live!.... minus the snow and subzero temps 😂 Run what you have and make it work, that’s how we do things.
@AlanDavid1955
@AlanDavid1955 3 жыл бұрын
Hey I got the gas tank out sooo many pin holes and holes. Do you have a email address I can send you photos
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Email address is on my web site VWJawbreaker.com Gary@vwjawbreaker.com
@redshirt-scotty
@redshirt-scotty 3 жыл бұрын
you ever wonder what commercials youtube sends our way? gmc just tried to convince me to buy a yukon!!??
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I do wonder that sometimes, we have no control over what gets played. At least it was a GMC commercial and not some feminine product commercial.
@KratzClassicCustom
@KratzClassicCustom 3 жыл бұрын
Idas come with 37 mm vents
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
I’ve seen them come with different sizes.
@vintage76vipergreenBeetle
@vintage76vipergreenBeetle 3 жыл бұрын
👍
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Stay safe my friend.
@andrewvassallo3444
@andrewvassallo3444 3 жыл бұрын
More air flow more jetts
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Yes but the venturis were slightly too big and I was losing vacuum signal at idle.
@dazbrowne4984
@dazbrowne4984 3 жыл бұрын
Thought they sounded great my neighbours wouldn't 🤣
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Luckily my neighbors are pretty cool and don’t mind me working so much. Then again, I’m never making noise real early or late.
@felixlafuente9714
@felixlafuente9714 3 жыл бұрын
Your jets in 44 are WAAAAAAAAAAAAY smal for a 48. Try stock jets
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Yes they were way too small lol
@VwRosstorations
@VwRosstorations 3 жыл бұрын
That sounded pretty fruity though.. 👍🏴󠁧󠁢󠁥󠁮󠁧󠁿
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Oh yeah, she’s a beast of an engine.
@masbeetleboy9169
@masbeetleboy9169 3 жыл бұрын
This project has promise. Go with the smaller chokes and slightly bigger jets
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
Yes sir, exactly. Would have been fine if I remembered what size valves I had when I ordered the carbs lol She ran great, just idled higher than I liked and lost some low end due to the venturi size. Smaller chokes and she’ll be just fine.
@VWRICH23
@VWRICH23 3 жыл бұрын
Man.... When i heard that idle, i was triggered lmao.. Just sounded like mine used to 😫
@VWJawbreaker
@VWJawbreaker 3 жыл бұрын
She didn’t want to idle correctly due to the size of the venturis.... so much air moving through the carbs. However she would scream even more at higher rpm’s.
@brianchisnell1548
@brianchisnell1548 2 жыл бұрын
Only German parts on my German car.
@VWJawbreaker
@VWJawbreaker 2 жыл бұрын
Everyone has a preference 👍
@ThePOTUSofMatthewEmbryBradshaw
@ThePOTUSofMatthewEmbryBradshaw 3 ай бұрын
I was expecting to see tuning and syncing, like you said. Click bait. Thumbs down on this one!!
@VWJawbreaker
@VWJawbreaker 3 ай бұрын
@@ThePOTUSofMatthewEmbryBradshaw I didn’t say this was a how to tune and sync video.
Jawbreaker's 2054cc Leaking Oil? Let's Check it out!
9:05
VWJAWBREAKER
Рет қаралды 2,5 М.
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 56 МЛН
BAYGUYSTAN | 1 СЕРИЯ | bayGUYS
37:51
bayGUYS
Рет қаралды 1,3 МЛН
It’s all not real
00:15
V.A. show / Магика
Рет қаралды 16 МЛН
3 REASONS Why Everyone Should Own One Of These!
6:00
Steve's Small Engine Saloon
Рет қаралды 20 М.
Tuning Empi 34 ICT / EPC Carbs for your Volkswagen - Lean Best Idle
15:47
300 WHP TURBOCHARGED VW Beetle - 1st Test Drive! | JW Classic VW
16:47
How to synchronize IDF carburetors
15:00
Volkstroke VW
Рет қаралды 53 М.
VW Air cooled PERORMANCE mods that DONT Work and ones that do
25:19
Mike Fn Garage
Рет қаралды 12 М.
How to Fix BAD body panel gaps FAST n EASY -  Metal finish - NO body filler ! D I Y Auto Restoration
16:10
Guzzi Fabrication - D.I.Y Auto Restoration
Рет қаралды 105 М.
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 56 МЛН