Thanks for the video, but i have learned that ultrasonic sensor in real world scenario is not reliable due to extreme cold in winter, high temperature in summers and due to humidity conditions. So using wires as sensors is more feasible and prune to all above mentioned conditions. So will you make its version 2 video in which you overcome all these problems and include some more must have features like manual switch to turn on/off motor at any time, make it wireless using RF modules as they are very cheap and it will solve the problem if the tank is at 3rd 4th or even at higher floors. looking forward. thanks
@protechnology5502 жыл бұрын
Asalam alaikum sir m ne bunaya but mara circuit on hota hi tank full show krna shroo krdata ha or LCD pr clear display sho ni ho rha side se dakhne se clearly Nazar ata ha or fornt se light show hta ha please help me thanks .
@pierricdoublet62485 жыл бұрын
Marche très bien ! super!
@yirgalemteshome37824 жыл бұрын
wowww great good project
@pradeeshkuttiyath50915 жыл бұрын
Good project 👍👍👍
@mohamed5yaz8056 жыл бұрын
super bro
@dawoodips3 жыл бұрын
Awesome project , actually I want add buzzer to it , when the water tank is full the buzzer should beep for 10 seconds then it should off plz upload the code
@furqanali5905 жыл бұрын
sir wire suggest kren mara lia mujha atleast 50 meter ka wire use krna ha sensor k lia jo sensor ko tanky tak pohcha saka but i used telphone wire us pr sensor direct kam kr rha tha withoute sense kya
@cypherLabs4 жыл бұрын
Good one
@protechnology5502 жыл бұрын
Sir my qarduino front ic chip heat LCD black please tell me solution?
@ashildapalpin76826 жыл бұрын
Nice
@Abhishek-vk6lk4 жыл бұрын
Can this relay work for submersible pump
@atmoss90894 жыл бұрын
Hello... is it the same, if I use arduino uno? Thanks
@furqanali5905 жыл бұрын
sir may is m delay off timer brha sakta hun na?
@protechnology5505 жыл бұрын
Sir please tell me this installation If I install Altura sonic sensor with long wire on top roof Tammy and all module down side install so will Altura sonic sensor data not lose By long wires please clear my question
@Trustmeiamanelectricalengineer5 жыл бұрын
Don't worry about that the data is already processed in the module
@protechnology5505 жыл бұрын
@@Trustmeiamanelectricalengineer it mean I can use longest wire on sensor ground floor to third floor
@zahratravelholidays97974 жыл бұрын
@@protechnology550 use cat 6 wire but morthan 10 MTR sensor not working properly. maybe ...!
@furqanali5905 жыл бұрын
sir why are you using push switch and 10k variable resistor?
@Trustmeiamanelectricalengineer5 жыл бұрын
To set the depth I am using 10k pot... And to change the mode between measure mode and control mode I'm using push button
@zahratravelholidays97974 жыл бұрын
If with in 30 second or water level 10℅ not should be motor off how write that code ?
@priyankamenon43695 жыл бұрын
How can I connect this with Blynk Application and view the readings?
@Trustmeiamanelectricalengineer5 жыл бұрын
kzbin.info/www/bejne/m3XOgaGXd7iMmrM
@protechnology5505 жыл бұрын
Sir sensor data lose when I use longer wirse
@Trustmeiamanelectricalengineer5 жыл бұрын
Is it... I may due to reduction in power... Make sure the supply is 5v for sensor
@zahratravelholidays97974 жыл бұрын
@@Trustmeiamanelectricalengineer Amp.?
@sachhin15352 жыл бұрын
Bro I will doit but not working pls help us
@syazwan7683 жыл бұрын
Hi why my motor don't run.
@aflick35055 жыл бұрын
Can we connect AC motor directly to the relay?
@eeekid66724 жыл бұрын
Use contactors
@alphabook5 жыл бұрын
Can it be connected to wifi module ? I am interested in only knowing the water level in the underground sump . Where can I buy it ?
@Trustmeiamanelectricalengineer5 жыл бұрын
Yes u can...
@AMOL81435 жыл бұрын
You forgot telling about rasister 200 ohm , as per your circuit , plz lets us know which rasister it is
@zahratravelholidays97974 жыл бұрын
And add to low/high voltage protection also
@furqanali5905 жыл бұрын
sir my circuit ato matic ly show relay off and on sensor no response sir cuit on and cut off and lcd show full tank when circuit cut off and lcd show level 1 depth 0 and continue blinking lcd in on condtion
@Trustmeiamanelectricalengineer5 жыл бұрын
That code will be updated soon for u with an upgrade using i2c lcd and replace the potmeter ect.. With digital push button.. I will update it soon as possible... Thank you for following me
@furqanali5905 жыл бұрын
THANKS SIR I M WATNIG UPDATS @@Trustmeiamanelectricalengineer
@backspace27zul5 жыл бұрын
is there an updated code for using i2c
@kailashmalviya83 жыл бұрын
Coding kaha se sikhe iski arduino
@backspace27zul5 жыл бұрын
is there an updated code for using i2c
@SDTECHOrayt3 жыл бұрын
Ladder Diagram of this circuit Please
@gulfamahmedshaju22325 жыл бұрын
Hello! How can I run this without a potentiometer. What changes should I make in the code if I am doing without a potentiometer.
@Trustmeiamanelectricalengineer5 жыл бұрын
U can put the depth of the tank directly in the program
@EldhoDavid4 жыл бұрын
any updated code for i2c
@prathameshlabde5 жыл бұрын
plzz show me the right connection of rellay bzz when i start this then lcd diplay dint work sir plzz rply fast
@Trustmeiamanelectricalengineer5 жыл бұрын
Can u please tell me what type of relay u use..??
@Trustmeiamanelectricalengineer5 жыл бұрын
U can download the circuit diagram and compare it with urs
@prathameshlabde5 жыл бұрын
Can you give me u r WhatsApp number I will show you the pic
@prathameshlabde5 жыл бұрын
Or email address
@Trustmeiamanelectricalengineer5 жыл бұрын
hajjamalfaizal759@gmail.com
@kavinavishka33694 жыл бұрын
Hi brother are this surely work?? Please tell me I'm gonna make this
@Trustmeiamanelectricalengineer4 жыл бұрын
yes it will work but make sure the sensor sufficiently above the water
@kavinavishka33694 жыл бұрын
@@Trustmeiamanelectricalengineer Brother its working but I can't cahge Distance in potentiometer what is that poblerm?
@kavinavishka33694 жыл бұрын
@@Trustmeiamanelectricalengineer And also brother how much ampirs want to give arduino nano the poblerm is I will connect it to mobile charger it was not working
@markowencalabia79145 жыл бұрын
Does the pump work here? please reply
@Trustmeiamanelectricalengineer5 жыл бұрын
Sure... Replace the bulb with pump
@markowencalabia79145 жыл бұрын
We are planning to do water level controller. So if the tank reaches the maximum level. The pump will work. Can i use dc pumps for presentation purposes only?
@Trustmeiamanelectricalengineer5 жыл бұрын
@@markowencalabia7914 yes u can... Use any type of motor the relay will act as a switch..
@furqanali5905 жыл бұрын
yes'
@s.k.c13395 жыл бұрын
Sir, LCD display faces a contrast related problem. It can't provide sharpen contrast. Please help me to solve this problem.
@Trustmeiamanelectricalengineer5 жыл бұрын
Connect a potentiometer into v0 to solve this
@furqanali5905 жыл бұрын
sir i chack sooner sensor with 30 meter longest wires but my device show tank full on lcd and relay off
@furqanali5905 жыл бұрын
and with out sens my sensor work by 30 meter long wires use solve my problem please
@Trustmeiamanelectricalengineer5 жыл бұрын
Please replace the potmeter and modify the code that fed the tank height directly
@karibasavatg41375 жыл бұрын
Can u send me the code
@furqanali5905 жыл бұрын
sir make wire less water level controller for professional level please
@Trustmeiamanelectricalengineer5 жыл бұрын
Sure.... But i am little bc....
@furqanali99675 жыл бұрын
Where is code sir
@Trustmeiamanelectricalengineer5 жыл бұрын
see description
@protechnology5505 жыл бұрын
Sir I make it but I chack my circuit LCD not respons and LCD blinking speedly how can I work by it
@Trustmeiamanelectricalengineer5 жыл бұрын
@@protechnology550can you please send a detailed description about your problem
@protechnology5505 жыл бұрын
@@Trustmeiamanelectricalengineer Sir I on my circuit by 5 v. Mobile charger and Arduino on light led sometime on and LCD screen blink speedly when I push the button then screen still on sensor not response of any kinds Arduino per light also on relay red light on only