water pump change 2013 5.7l hemi charger

[@terranceblock9007]

Thank you for tbis vid. I just changed out my water pump and your video was spot on. Thank you for your time knowledge and experience.

[@EfurdGarage]

Your welcome. glad it helped

[@WillsWheels]

Looks like cheater bar has seen a lot of use....LOL. Great tip putting the bolts in the new water pump as you go. Another great video!

[@EfurdGarage]

Thanks Will. And yea it has seen alot of use. cant tell you how many times it has helped

[@ericengland5158]

Put the pullies on the new pump before you install it

[@mohammed2010v8]

Great video you mentioned that water-pump bolt are different lengths, all the bolt the same size head is it 15m all around the water pump bolts

[@EfurdGarage]

Yes they will still all be the same head size. I believe 15mm is correct its been awhile since i done one of these

[@JuanaNava-mz5tc]

Thanks ! Mexicali BC Mxc

[@EfurdGarage]

your welcome

[@b5beast611]

Nice work! 👌

[@EfurdGarage]

Thank you!

[@quietstorm1732]

Do you recommend draining coolant before changing water pump mine hasn’t gone bad just squealing on start then goes away so far

[@EfurdGarage]

you can and depending on mileage its worth it since most coolant you should change it after x amount of miles.

[@IronHorseGarage]

Yes siree!!

[@EfurdGarage]

yea!!

[@imhyper5490]

Great video, just how long would you say for the coolant to reach and cycle through the water pump to get to the radiator and start dripping from water pump plug?

[@EfurdGarage]

It didnt take very long, It also depends on how much coolant you drain too.

[@imhyper5490]

@@EfurdGarage Thank you, but I ran into a problem...I did what you shown in the video however but now the coolant isn't reaching the radiator through the water after I filled so it drain through and my car still overheats. No leaks or anything, just not going through the water pump to the radiator. Any idea why?

[@EfurdGarage]

@@imhyper5490 should be good and the water pump should be moving the water. Fans kicking on and have you checked the oil?

[@justinellison5147]

This was helpful thanks!!

[@EfurdGarage]

your welcome, thanks for watching

[@Eric-fn8zv]

Thanks man

[@EfurdGarage]

your welcome

[@youngnick1800]

When u put that bottom hose on did you have to get underneath the car?

[@EfurdGarage]

i did it up top but if it is easier for you, then go underneath

[@coreywhite4603]

Was it over heating ? Mine is sending water back to the reservoir, bubbling and Boiling coming out of the overflow and temperature, gage steadily, rising what could that be?

[@EfurdGarage]

yea but the pump went out so it was leaking out the hole and on to the belt. Well if you start it cold and its already bubbling out before the car is warm then it could be a head gasket

[@coreywhite4603]

@@EfurdGarage I really appreciate you taking time to respond. It means a lot.. yes after about 20 minutes of running it start sending fluids back to the reservoir bubbling and coming out of the overflow. I had just put a thermostat on 2 weeks before this situation showed up . no leaks anywhere but yet after 20 minutes or so of running this is what it does.

[@EfurdGarage]

@@coreywhite4603 ok after 20 mins of running odds are its not head gaskets. Could be pump. Could be thermostat sticking even if it is new. Could be a collapsing cooling hose. Fans could be weak they should be kicking on and flowing enough to cool.. And just to chrck you Did you bleed the system after the thermostat?

[@coreywhite4603]

@@EfurdGarage yes I did bleed it. You just made a good point about the collapse water hose. One of them are looking suspect.. thanks a whole bunch once again . Inwill also change that thermostat out again.

[@coreywhite4603]

I took your advice on changing out my thermostat in which I had just put on two weeks ago, and would not have guessed it could have been that but turns out it was. I would like to thank you again

[@jemelking25]

How long should this job last? 2 hours?

[@EfurdGarage]

Vairys, depends on tools and experiance. Of course if everything goes smooth. But around 2 is not a bad time frame

[@jemelking25]

@@EfurdGarage cool

[@jemelking25]

@@EfurdGarage thank you

[@outdoormoreservicesllc1897]

great work very helpful, do you have one on the timing chain on same vehicle?

[@EfurdGarage]

Thank you. Sorry i do not.

[@britjohnson1990]

Thanks! Too bad mopar didnt design the water pump like on a big block where 4 1/2 inch bolts takes just the impeller and pulley off.

[@EfurdGarage]

They cant make anything simple anymore

[@britjohnson1990]

@@EfurdGarage yeah it might cost $2 more to make it. My drivers side bents are stuck on hot air. Im sure the gear from the servo motor is broken that moves the vent door. 🙄Ever seen a cable setup break?

[@EfurdGarage]

@@britjohnson1990 yea ever since they went to blend door actuators i always here issues with them. I have seen a few cable setups break but it took way longer then the newer stuff

[@britjohnson1990]

@@EfurdGarage yeah they can fail no doubt. Cables are good for light duty stuff like chokes or vents. I used to shake my head when I first saw the mustangs with the cable clutch linkage🙄

[@britjohnson1990]

Hahaha! Exactly. I remember in the early 90s seeing the mustang cable clutches that the ford kids had and laughing. They would get a hipo pressure plate and it would stretch or break.

[@thecarguy2470]

No air tools? Sure makes any job easier and much faster.

[@EfurdGarage]

It really does. I do have air tools. But most of the time its a hassle to get to my compressor, turn it on, un roll the hose etc. I always have to move the gto in order to even get to it.

[@hereallmystuff]

Awesome How long from start to finish did it take?

[@EfurdGarage]

i dont really recall but i wanna say around an hour with filming