Weber carb struggle to start 1

[@Michael-1205]

Just want to say thanks for the tips. I followed all your tips including timing, checking plug leads, checking individual spark to each cylinder, air leaks with carb cleaner etc. I have had issues with my 38 dges on a Essex V6. She was hunting like mad after the warmup start. Then while I adjusted the idle screw up a bit and gave a tap on the accelerator I heard a gunshot going off and she then idled like a hot knife through butter. Smooth as glass. Thanks again for a good video.

[@carburettorrebuildservice8964]

Thanks for watching my videos.

[@JimboJangle]

Very useful.Great to watch and listen to the carb running and the adjustments.Thanks.Appreciated.👍🇬🇧

[@carburettorrebuildservice8964]

thanks for watching my videos, glad it could help you.

[@paulliquorish2180]

Really interesting and informative

[@carburettorrebuildservice8964]

Hi, thanks for watching my video's, glad it helped you.

[@neilrobertson1345]

Never had a problem getting a weber to start any motor they brilliant carb lot better then a Vairjet

[@carburettorrebuildservice8964]

Thanks for watching my videos

[@gumjidio4844]

Thank you for sharing your time and experience. You are a saviour to a "backyard mechanic" like me :).

[@justinrydar4253]

If you happen to see this.. I need help with my Weber on a Suzuki samurai. I recently redid my head gasket and have spark, for some reason I can’t figure out how to get the carb adjustments right for it to start. It’s a 1.6L 8V with an older Weber but it worked fine before

[@carburettorrebuildservice8964]

hi, what Weber is it, are you sure it is the carb?

[@crowwergaming7704]

Can u do a video as well for idling issues where to check and what can cause it to idle to low or idle to high

[@carburettorrebuildservice8964]

Hi, will do. thank you for watching my videos.

[@craigchiddo2794]

Im running a knockoff 55dcoe on a 4.9 straight 6 efi manifold converted when it's over 75 degrees outside it starts well when it's cold I have to flood the manifold I need to figure out a way to heat the manifold in cold weather

[@carburettorrebuildservice8964]

Some of the carbs had an electric element on that you can use. alternatively you can use a glow plug from a small diesel engine.

[@craigchiddo2794]

@@carburettorrebuildservice8964 I'm thinking a decent oil pan heater under the plenum

[@mariusschmidt2419]

I need help. Purchased a beautiful nissan 1400 with a 276 cam and 32/36 weber the problem I'm having is starting as well as pullaway have to rev it high in order to pullaway I'm not sure where to start troubleshooting. I did service the cab but still facing the same issue. I don't have an issue with idling or when driving its only starting and pullaway thats problematic

[@carburettorrebuildservice8964]

please ensure you have no air leaks and disable all the fuel enrichment systems. on my facebook page i have jet charts that you can use, it is the same name as my channel

[@mariusschmidt2419]

@@carburettorrebuildservice8964 I found the problem it's leaking air on the shafts that the accelerator cable hooks on. If you move the shaft it has some play and can hear a difference in the idling of the engine when moving it around

[@carburettorrebuildservice8964]

@@mariusschmidt2419 Are you in RSA, if so we can re-bush the carb for you.

[@marietjienel4876]

Mazda Magnum V6 Essex engine - Weber carb, float bowl leaks, vehicle won't start if not used for a few days - petrol ends up in the sump over time, increasing the oil level and diluting the oil. No fuel leaking on the outside at all. Any suggestions?

[@carburettorrebuildservice8964]

you say the float bowl leaks, can you see it leaking? do you have a heat insulator under the carb? do you have the return pipe connected? you can whats app me on 060 654 6966

[@hankpb1]

I've just rebuilt my 34 dgas and car won't start now unless I squirt petrol into inlet manifold.any ideas

[@carburettorrebuildservice8964]

Hi, 1. check for any air leaks 2. ensure the idle jet is open and idling is adjusted correctly 3. ensure pump jet is working correctly. i hope this helps

[@hankpb1]

@@carburettorrebuildservice8964 do you the 2 idle screws up tight?

[@DanielJones-jt5iz]

Good day sir im drivong a 1100 fiat uno mia 2002 model i have irregular idling issue's i checked all air leak testing but i have a question my carb has a anti flooding adjustment screw at the back of the carberator there's a pipe that goes into a mechnism that adjust choke when air is being sucked through and i have noticed it doesn't keep the mechnism open when i suck on it , it keeps but then it puls back does that also affect air flow that causes irregular idling ?

[@carburettorrebuildservice8964]

Hi Daniel, what is your location please?

[@crowwergaming7704]

How can i get in contact with u for some parts im needing for my weber carb or any places u know where i can get parts

[@carburettorrebuildservice8964]

Hi, are you in South Africa?

[@crowwergaming7704]

Ja ek van Suid-Afrika

[@carburettorrebuildservice8964]

@@crowwergaming7704 Whatsapp my op 0606546966

[@misheckjojo4026]

@@carburettorrebuildservice8964hi