What Does Aux 1 Do? | Audio Mixer Aux Output Setup

[@andrewp1513]

Man…you’re really good at explaining this stuff, especially for people who use some of this gear a little bit don’t understand it’s full functionality. I never really understood pre/postfaders till now. Thanks a lot 👍

[@johanvanhuyssteen9217]

I always enjoy and appreciate your videos at the same time. Calm, informative, no bullshit. Thank you.

[@BotraxDiaz]

I run an Aux channel for people on the phone line, and another to Skype/Zoom in the computer, both with MinusMix for their input slider.

[@jessgayatao8687]

Great info! May you not get tired of sharing your knowledge about the sound system and how things are done properly. Thank you and please continue in your good deed.

[@LarryOohLaLa]

That great brother 🎉🎉🎉 most likely I used the auxiliary for reverb and delay separating for vocal on analog mixers, but on the digital is totally different ❤❤❤

[@bikersoncall]

A video on making some of these connections might be quite useful to most of us. Just take a stomp box delay unit , something simple and 1/4'' cables to make these connections. After watching lots of videos, and not finding an ans for adding a processor or simple delay unit to my small Yamaha MG10XU mixer, through trial and error I got it done; Yamaha 'effects-send' to the line in or 'in' of my external effect (delay unit) then from the 'out' of my delay unit to a line in or mic in of any channel. My MG10 does not have aux sends.

[@GlennFiddles]

Thanks

[@kettnercreative]

Thank you so much!

[@WINSTANLEYOBXa]

With this mixer You’re saying to run external Effects you have to commit another channel to just effects return (AUX2)?

[@Initial_Gain]

I see there is also Aux2. I'm assuming this you set the internal effects of the mixer separately per channel. But can you send Aux2 signal from the Aux2 send output WITHOUT the internal effects? So that I could use Aux1 for Left and Aux2 for Right for an external stereo effects unit input. Thank you very much for this clear tutorial that is rare to find elsewhere.

[@alomond]

I have a 12 channel with 2 aux sends per channel. 2 aux output mains jacks. There is 1 return 1/4 jack. I assume that the intensity of effect is controlled by the aux send on each on channel and the return pot?

[@DUKKDISORDER666]

can i use the aux output for connecting my audio interface

[@NitinTomarMusic]

Thanks so much for your video. I have two questions. 1. Does the PRE button only impacts the aux 1, or both Aux1 and Aux 2? 2. There is a single knob for Aux2 and FX. So it is duel purpose knob? Controls Aux2 volume as well as FX intensity for the channel? Thanks in advance.

[@jgirizarry]

I connected yesterday a Zoom H6 via 1/4” cable on both ends to a mixing board, I connected it to an Aux and my final recording was pretty bad. I could barely hear the instruments and the vocals sounded at a distance. I activated the -20db pad on the Zoom. Those aux outputs were used for headphones, but the sound tech told me that I could use them. I am not sure what happened.

[@jhoestring]

Hi thanks for sharing this tutorial. Very helpful. May I ask, Is there any way that I can convert an aux output into aux input?

[@billyjackson9406]

Nice!!! Do you have a video on how to connect amps to the mixer using the aux input?

[@bikersoncall]

You would not want to connect an 'Amp' to an aux input, unless the amp has a 'line' out, NOT A POWER OUT from an amp. However, you might be asking how to connect the line-out of a guitar amp or keyboard amp,' to a mixer, which could be done with amp line out to any mixer channel.

[@MarcoRomero-m3y]

Am I able to hear EFX through the AUX sound if I'm using it as a monitor?

[@hollywoodthedj1673]

I run my subs through the aux channels for separate volume control when I do that should I leave the aux 1’s pre fade off and on post so that it matches the aux 2 volume

[@terrymcfadden1615]

Great Video - Interestingly, I have that very Yamaha mixer, the 12MG XU. The question that has been driving me nuts is what set of outputs to I plug my EV18" powered subwoofer into to run independently of the main speakers. I've heard that i should NOT use the MONITOR outs, which seemed the easiest solution. Would I use the AUX sends or perhaps the GROUP 1-2 outs?

[@coliwobbles514]

I believe it’s via Aux 1 or 2. The monitor outputs are literally for studio monitors and not floor monitors. Seems dumb to me but worth a try.

[@QuikTechSolutions]

Hi, great channel, recently subbed. I purchased the Yamaha MG10XU for a live show that we will be taking on the road. I’m new to the audio mixing space. Your videos on this mixer have been most helpful, thank you. Question - I need to take two line outs from the mixer. One is to send the mix to an Atem Extreme for the livestream. The 2nd line out is to feed a house audio system. What are your recommendations for achieving this? Thanks in advance.

[@kettnercreative]

I would use a 1/8" TRS to dual 1/4" TS cable (currentprice.io/14_to_dual_18) to go from your stereo outputs into your ATEM. Then send the XLR inputs to the house sound system.

[@samisaac3908]

Does subwoofer sounds better when fed through Aux send from a Mixer?

[@Ray-yt7mk]

I have the Yamaha mg12XU!If I want to run my subwoofers separately and use the aux send,how should I plug my two subwoofers?

[@frankgreco]

Very informative. Although I didn't understand how exactly to connect an effects unit (eg, reverb/delay) to my vocalists. I understand the Aux out and the Aux mix control, but how do I get vocals to go to the efx unit and then return?

[@bikersoncall]

I can't address the 'aux' jacks, my MG10XU only has 'Effects-Send*'. I plugged a 1/4'' TS into my Effects-Send, and other end of cable to a delay unit 'in', and went 1/4'' out of delay unit to any channel 1 or any channel. I'm guessing aux out is similar to effects-send, with maybe different routing. Let us all know what you find out.

[@anupam2905]

Does the Aux 1 and Aux 2 work in the same way. Whether we can get Effects (Reverb) in the Floor Monitors on Stage through Aux 1 and Aux 2. Or can we cut off effects (Reverb) in the Floor Monitors through Aux 1 or 2

[@coliwobbles514]

I believe he mentioned this is the pre and post fade section. I would try pressing down the ‘pre’ button on the selected channel and turning the aux dial to either eliminate reverb (all the way down) or turn dial clockwise to add reverb.

[@andrewsmatt9042]

How to connect aux in djm pioneer 350 for streaming video what I need

[@thesmallnotesduo]

Awesome videos my friend - thanks a lot.

[@efclee1]

Hi Jordon We have the Yam Mg12Xu and use for vocals and guitar , what is the best way to use so vocals and guitar can have own controls into the monitor so the guitar doesn’t owner power the vocal , we just have the one floor monitor we both share

[@djfingersflores]

good stuff man.. thanks

[@stevemccray4458]

This is off subject But I want to know how to connect Dante adapter to my mg 12xu

[@OlaJendor]

Very clear explanation

[@MusicFeedsMySoul100]

Awesome video on using the Aux! Firstly a massive thanks to Kettner Creative, it's thanks to you that I know how to use my MG12XU mixer. One question though, if I wanted to have multiple monitors with different mixes controlled by Aux1 would that be possible, or would I have to use aux2 for a separate mix and be limited to two monitor mixes? Thanks again for all the useful content!

[@kettnercreative]

You have to use a separate aux for each mix

[@blazinSpike]

Great video

[@guytobernard1948]

I can’t get a good sound when recording acoustic drum with the mackie profx16v3

[@averagepainter]

yes, where is the return input after you sent the audio through the send output?

[@kettnercreative]

You can connect it to any input channel on your audio mixer that you want.

[@averagepainter]

@@kettnercreative i see. But i wont have the "traditional" control over its amount per channel, only for all channels simultaneously?

[@salvationtabernacleministr9554]

Hi sir please Yamaha mG12xu full review explain ❤ I'm waiting

[@JL.bararA]

Wait, how do you use aux send on a Livestream?

[@sf.a.1]

Thank you very much!

[@hernanreyodiaz222]

The aux output is mono. How can you convert it to stereo in order for your earphones to work left and right. ?

[@kettnercreative]

You would need to use two aux channels if you need stereo.

[@hernanreyodiaz222]

​@@kettnercreative2 mono ts to stereo trs? Thanks for the reply

[@SJGR81]

Always helpful. Thank you.

[@Gladingson1]

well explained, Kudos sir

[@wiratamadean5994]

So Aux the Pre-Fader function means I can have different output besides the Main output? That means I can control the Aux volume separately from the Fader and not effecting the Main output, right?

[@kettnercreative]

Exactly

[@xoyleid8358]

Aux Output .. what Kind Needed ? .. Is It MonoTS or Stereo TRS ?

[@bikersoncall]

I believe this would be ts , not trs. Let us know what you find out.

[@wilkopiano]

What about stereo aux output ? Wouldn’t you have to use both aux one and two? Then you lose pre or post option. Why is it so elusive to find a budget mixer with 16 aux mono / 8 aux stereo outputs for iem mixes.😂 they seem to cost the earth.

[@kettnercreative]

Most people looking for 8 stereo monitors would have an input list with more than 48 inputs. This would easily put you in the territory of a full scale digital setup.

[@sheltonhargrove6353]

u don't show nothing visually u just talk! show wire connections

[@VanillaPlays]

First!

[@kettnercreative]

Aha, nice.

[@marklone826]

ein paar beispiele wären gut gewesen

[@леонидадсаламов]

Много пустой болтовни....урок ничему не учит.