What Went Wrong? New Vinyl Wrap Brand | Demo Full Hood Wrap

[@ravynnblood2580]

HIGHLY recommend that you remove that, READ THE INSTRUCTIONS, and REAPPLY CORRECTLY!!! Disappointed in your lack of preparation on this one man.

[@CKWraps]

Justin Pate recommends to leave it on for the flat areas which is exactly what I did. If you go watch the video you'll see. Here's the link in case you missed where he says this at 5:45 kzbin.info/www/bejne/eomQo61rm655pq8

[@fsmautorestyling9552]

She would break her ankle on one of those damn things. Lol She wasn’t talking about the liner part. 4 cars deep in this stuff and I can tell you she is right. Missed the part where he said to glass. Running fingers to the edge is not glassing. Most of that hazing was on your part when you would heat it and pull it away from a spot that was already laid n stuck. Plus doing a review on a product that has been pulled for issues a month ago is a no no.

[@CKWraps]

@@fsmautorestyling9552 so the random adhesive build up has something to do with heat? Heat wasn't used when that happened. Also how about the permanent impressions left by something sitting on the film? Only time this occurs on any film is when magnets are left on it. Also what about the marks that are approximately 1"-2" long and run in different directions when the cap was left on during that part of the install which is recommended to be done? I think there are more important issues to be addressed here than just the color fade. The results of what this film looks like are instantaneous and it should never have hit the market. That's negligence

[@fsmautorestyling9552]

CK Wraps I can agree with it that it did drop to early. Way to early. The marks that go in different direction are from un even squeegee stroke pressures. Use heat and squeegee them out. You have to go over it with a round of heat and a wrap glove after you get done doing the install. Wrapsesh channel goes over this step in detail on a four runner. The glue dots I have no clue what you did to get those. Wasn’t an issue for us. As for the comment below. I did upload one of the videos on to my page. It’s not a review but it’s cheetwrap. Gloss grey Supra.

[@fsmautorestyling9552]

The heat part I was referring to was wen you were workin the down ward slope sections of the hood side wear your material was bunching up.

[@con2rito]

You make this look so ez bro, I admire your talent

[@gregoryjenkins1461]

Word... I've been working up the nerve to do my hood in CF again... I bet he could do it in 5 minutes or so...😂😂😂

[@kevinb7568]

Just wanna say thanks, man. I wrapped my first car after watching your videos. You're the man!

[@Lsxiroc85]

They have already pulled the gloss colors to fix these problems. Their website shows the dates when they are going to be released again after they fix it.

[@chichesterbuilders]

This is my professional opinion, if you don't know what went wrong, well then it's just bad product... Really just that simple!! Love watching your videos. Your as good as anyone I've seen so far.. Without a doubt a master vinyl guy

[@KantstandlamGarage]

That was quite satisfying when you took the cap off.

[@mese600]

The liner from the 3M galaxy black is as flexible as the vinyl itself. Makes it really easy to install.

[@joshuaslawncarellc]

I WOUNDER if the markets you said look like crakes were caused from pulling with the protective cap still on knowing the cap has very little to no stretch!! It may be forcing pressure markes in the vinyl !! But really the finish just looks sketchy all around! THIS video have changed my mind on wrapping my hood roof and trunk in gloss black.Think I will go with the carbon fiber look now !!!!

[@michaeln.7083]

If you had issues with this I myself wrap at home that material is garbage, I wouldn't recommend it!!.. great video

[@FadeToBlackLLC]

I've been waiting for this...we know that Gloss Black shows everything. I have Avery on my truck with chips and it doesn't look the greatest either. Good video though, curious to see how the Matte lays down?

[@gocardogo]

Great video man! I’m learning every time !

[@diegosolar678]

that vinyl looks so easy to install on your videos, everyday i learn something new on your videos

[@carmensancheza2d995]

Very informative video Christian! The camera work is def a lot better now! The transitions etc! Keep up the good work! I would like to see a video about your personal background and how you got into wrapping!

[@navfrancis4516]

CarmenSanchez A2D he already has this video on his channel from 2-3 months ago

[@chrysfil9810]

This is very similar with the vinyl I used for the doors of my kitchen cabinets (£6 for 2m×5m). Nice and very informative video, thank you 👍

[@dontbestupid6664]

You gotta start partnering with suppliers and doing ads. You made me get a pressure washer after watching your video on prepping the cars just because it made my pep work so much easier. Love your channel.

[@hamadkhan8161]

Learned a lot from your videos, sir. I am so excited to wrap my Supra soon!

[@scubasteve2347]

I saw the orange peel before you even pulled the cap. I think I will stick with the better films

[@kevinl.705]

I'm going to wrap the hood of my RX-8 when my product comes in. Thanks for the instruction.

[@meatandpotatoman]

Love watching your videos. I learn something new every time. You have inspired me Sir! Thanks for sharing and being transparent with your video editing too.

[@CaptBrad-iy2ux]

Thanks for another great video Christian. Before watching your video, I just finished using gloss black Cheetah Wrap on a boat color change and had exactly the same problems with the random markings and shift in color. I also left the clear protective layer in place for the large flat areas. I couldn't believe the inconsistency in the final finish after removal. Just to be clear, I watched Justin's video, and installed the product as directed. I wont use it again. While the product is very easy to install, the finish is lacking, and the need for 100% post heating is just too time consuming. I much prefer Avery for a low tack film.

[@plokijij7856]

The Matt out is a delamination between the colour and the gloss

[@tedlumley4470]

I wouldn't have installed it any different than you did. Aside from some stone chips showing thru - the other issues would've been very frustrating. At least it's your own car.

[@stk928]

Nice review! I believe all these problems it has are to do with the adhesive of the film, otherwise it looks nice for the installer and overall nice gloss black. Have you ever tried Isee2 brand film?

[@ajones9606]

Hey man love your content always quality, honest and reliable. I’m looking to start up a wrapping business down in Australia out of home for now to try and get out of my 9-5 job just wondering if you could talk a little about something on the lines of new business start ups, ups and downs and share some personal insight of how you made it to the top. Thanks in advance :)

[@beyondoffroad488]

@CK Wraps Did you ever do a followup video on this. Not about the issues you mentioned per-say but just about the durability of the adhesive and such? Also have you done any other videos using Cheetahwraps? Maybe the other styles like @@UCKY1c84hd1Y9r3G0v26GCBg said in his comment below. We have installed the Satin Nardo Gray on a WRX that seemed lay out well. The front bumper and spoiler were a pain in the neck but I doubt that its the film..... and probably the shape and our inexperience. But I'd be curious to see what your thoughts were on the Satin product. Thanks again for all you do. We appreciate the real world information and instructions you provide.

[@chashastings6861]

Thank you for the time and information .... do you do windshield wraps

[@lonamarlonamar815]

Hola no entiendo nada de inglés, pero te hacerse entender muy bien miro todos los día videos tuyo por qué vos a ponerle vinilo a mi auto y cuando lo haga te mando un vídeo..... Sos un gran maestro gracias amigo.

[@stormin651]

Great video, I'm part way through wrapping my Hyundai FE and the hood is next on the list but annoyingly the front badge has failed twice now and wondered if you had covered the hyundai logo on any previous vids?

[@gnr4954]

thanks for the vids ck still trying to get the balls to wrap my 17 chevy ss. Just nervous to drop the money on the film and fuck it up lol.

[@joebutta7539]

What does the pattern on the air release look like? Seems waaaay too sensitive during and after install. I'm thinking their air release isn't perfected yet, like you said, doesn't seem to level off, almost like the air release doesn't "smash" evenly. The initial tac is great! But pointless if the result is that volatile to weight on top of film, discoloration in the finish, and scuffing. Very curious to see it in a week or so. Thanks to you and camera man for the vid.

[@andriivladyka7126]

Hello, Loved your video on professional vinyl wrapping. I followef you directions and wrapped the hood of my Mitsubishi outlander 03. That hood is heavily curved especially on the front. I started from the windshield side and when I got to the front it got nasty wrinkles on the front right side. Could you please advise me what i did wrong and if I can fix it? If I can't, how should I wrap properly? I will need to remove the old vinil and star from the beginning but is there a right way to do it? Thanks!

[@13bHappy]

You think running over wrinkles is some cause of glue lines? Or weird marks? That happens with most gloss black films?

[@edinm7825]

My Bmw look still perfect after 4 years with 3M 1080

[@giftedsage4591]

I was about to purchase some cheetah wrap to do my car. Would you recommend against? I’m looking to do gray gloss

[@karlpoglitsch1087]

So is there any value in this film maybe as a training film? I hate when my skill causes issues never mind the product being broken from the start.

[@nicspage852]

Did you get a chance to install the matte green? I’m interested in getting it wanted to know your opinion of it first !

[@jimhunt4507]

Gotta recommendation in Metro Detroit for paint protection like Xpel and ceramic coating?

[@tegugirl683]

First of all I wouldn't install on a warm or hot car, and don't install with cap sheet on.

[@chrisbroscoi3286]

Ya id rather spend the extra $200 for 3M or Avery instead of pulling my hair out installing this crap. I may try the satin on my personal truck and see what happens.

[@michaellam6085]

Hi Bro, Watch your videos all the times. Too bad you are not in Southern California, otherwise i would ask you to wrap the roof of my 20 Honda Accord. In your professional opinions, which film should i use for gloss black if price is not an issue? 3M 1080 or 3M 2080 or Inozetek you demo on one video? Also concern about damaging the clear or paint if i have to remove it one day. Saw a video from youtuber, his Porsche was damaged when he tried to remove the wrap. Ty Bro

[@corvairvert]

I'll just use Avery vivid and be done with it, why bother with this?

[@Bowtie41]

Can you apply Spot Putty to the chips before wrapping?

[@luamayav]

That's what I did and it worked perfect

[@MRahlie]

What films come with a cap? I had ordered vvivd gloss black and it didn't. Ended up with many scratches in the vinyl from the squeegee

[@airking1881]

Cant wait to do my G6 in Nebula Black!

[@Jdm_fl5]

Disappointed in the results but I'm going to wait for Frank F. to chime in I'm sure he is going to respond to this video

[@mlg6992]

What brand is that microfiber? Lol Looks super absorbent

[@axelst.776]

First one!Have been waiting for this one!

[@Twap]

Good video man keep up the great work!

[@normanevans1625]

CK Wraps first off love your videos man I wanna know can I find a good UV protection for my gold wrap I wrap my rims in gold an don't want them to fade I ordered it from metro restyling an a gloss rising sun I need a good uv protection what do you recommend thanks

[@davedominguez7687]

My dawg, big props

[@phasedpfeiff6432]

Is it at all possible to wrap over primer for the entirety of a vehicle?

[@flyby8049]

Other people have said you need to remove that cap before working on the wrap on the car

[@CKWraps]

Justin Pate, the supreme installer, says to leave it on

[@flyby8049]

CK Wraps I’d be curious to see you test it both ways

[@giftedsage4591]

How did it hold up

[@CTP1111]

kind of annoyied that cheetahwrap removed all the other brands from their site... I enjoyed ordering form them as they were the cheapest option with good shipping

[@rgerman948]

Can u buff the wrap? To make it look better?

[@mohammedpatel6336]

Love the hair cut

[@TRUCKERJOES]

Shit Wrap is more appropriate name never again, Avery and Hexis that's it

[@lilsilvers3613]

Have you ever double-wrapped?? Is it worth doing? Just curious!!

[@sharkeyshark4410]

Lil Silvers I have when I met a girl I didn’t trust, it was worth it

[@speedyspeed4082]

dirty sierra 😂😂😂

[@BBDUBS]

Not really worth it. Only time I know people do it is with a clear bra on top of it.

[@BRIANTDELEON]

Are you in houston?? Tx?

[@crxneoth]

I'd agree that this film needs a different technique. As professional installers we should be able to adjust to the material specific properties. Adhesive speckles/dots: come from dragging the material over the hood. See kzbin.info/www/bejne/nWXdZY14gp6Ja80 Indentation: I wouldn't leave a bottle on the hood anyway. Mattening out: Utilizing more film to stretch over the corner, 4-5 inch vs. only 1 inch, keeps down stretching under 10%.

[@KM-qk1oz]

What brand black wrap is that?? I used 3m but didn’t get that glossy reflective finish like yours

[@FadeToBlackLLC]

That's the Cheetah Wrap

[@JQUICK21]

I see you mentioned STEK black gloss ppt. Just watched a STEK Automotive video and those guys were spraying tons of liquid all over the film and even under it on the edges. WTF??????

[@CKWraps]

Yea because it's ppf, you wet apply it

[@JQUICK21]

CK Wraps I see, thank you

[@thejester8136]

I remember when Fellers first started carrying Cheetah Wraps brand and man was it junk, from what I remember it had like a texture all in it, and I was like nope. Almost like the air release was stamped into it and couldn’t get it out. What can you expect for $300 a roll though. Junk.

[@badmayofpv7103]

Fellers dont just carry it, they manufacture it!

[@c2herr]

I really loved the videos when I first started watching. I've learned a lot and am very appreciative, but they are making me sad lately because of the cocaine.

[@xrpbridges5421]

Great vid man pity the wrap wasn’t great dude

[@jasoncameron34]

Fail thats sad but im glad you did the review we know not to use it. Which wrap is best for beginners im sure i asked sorry, and would a roll do an 03 mustang and have extra because im sure id mess up lol thanks

[@cmaysautoyt]

Just because he has bad results doesn't mean anyone shouldn't use it lol cheetah wrap actually pulled all of their gloss films and are doing a re-release so he should do a video with an updated roll. He shit all over 3M but some people swear by it. Different strokes for different folks..

[@FadeToBlackLLC]

I like using Avery Dennison

[@jasoncameron34]

@@FadeToBlackLLC thanks i been looking at avery seens like best bang for the buck

[@FadeToBlackLLC]

@@jasoncameron34 it's just a good film to work with. I just uploaded a video with it.

[@hardhittit7596]

I just bought a roll of the cheetah satin black and I think it’s crap as well.

[@EyesOfTheInternet]

What brand is this vinyl?

[@con2rito]

I have a 2008 sti, I would like to do the vinyl on red. Any suggestions, on which one to use?

[@brandongunniers9967]

con2rito22 lol

[@ryandriverhidatsawarrior3034]

Well did you wrap it yet

[@RRios-zy2ut]

Ck ... which black gloss wrap has he most shine finish to it ...????

[@CKWraps]

Gloss black ppf by STEK is the nicest gloss black vinyl

[@RRios-zy2ut]

CK Wraps ... Thank u... I’ve been having trouble on deciding in which should I use ... cuz it will be a full wrap ... and should I use something, like a sealer or a type of wax after ?

[@anime44lover]

Looks like rookie wrapped it 😋

[@llaastatistic1323]

Good old USA quality

[@Pc.customwrapz]

I think that if it's a diy wrap, you shouldn't have to baby it to get it to work and setting a bottle on it and leaving permanent marks, WTH!! I can't believe Justin endorsed Cheetah. I was going to try Cheetah out on a full body wrap. Won't waste my money.

[@hawkeyestiguy]

Lol at the people getting butthurt that he is pointing out major issues with cheap wrap. His install technique causes a bottle to leave circles in the hood after 5-10 seconds? Are you serious?? Haha. Just admit that it is cheap & it sucks. All Christian is doing is putting out information so that buyers & installers can make better, more informed decisions.

[@thehawkguy]

did you start the video with leaning your jeans (with metal rivets) against the hood? dang man....maybe those aren't rock chips and maybe you need to keep a chair handy lol

[@CKWraps]

Exactly, I own the car and it has been used many times for training and demonstration purposes

[@sbisthname]

Have you ever done a motorcycle?

[@aussieflyer70]

Hey mate how are you, great video as usual, new ride?? what happened to the genesis?? looking forward to the Avery workshop........u sound a bit crook mate?? Flu??

[@CKWraps]

I'm good mate, getting over a cold. This is my ex wife's car I used for the demo

[@LurkMoar101]

@@CKWraps Ex?? Sorry to hear this my friend =\

[@Austin-mo1vy]

My school is paying to have my F150 wrapped! I’m thinking a charcoal gray it’s currently white, the issue is I will be the one applying it, any tips for a 2012 F150 extended cab? I’m very excited but really don’t want to screw it up thanks

[@illililililillli]

Why is your school paying for it?

[@Austin-mo1vy]

As a graphic design project to finish the senester

[@joebutta7539]

I know it's a raptor but CK has a bunch of f150 vids you should watch. Good luck with the f150, it's not the "easiest" lol. kzbin.info/www/bejne/jZSld2Njg5ard6M

[@Austin-mo1vy]

Joe Butta thanks for vid

[@valant963]

Do the vvivid nardo gray with gold flake

[@trevorbrooks2552]

CHEETAH RIP 🙉

[@KantstandlamGarage]

Cheetah wrap? Teckwrap?

[@CKWraps]

Cheetahwrap

[@mkm1856]

cheetah wrap....fellers + justin pate made it as a "cheap full rolls" option ($395/roll), only sold in US - w/ warehouses supposedly close enough to any area in the states for you to safely get 2-day shipping (for free) with each order... + it's cast vinyl, not calendared....like teckwrap (that shit would drive me absolutely insane, personally...)

[@r-mackphotography6424]

Seen KPMF films that finish better than this.

[@CraftinSkillDIY]

Дать бы тебе китайскую плёнку 5стар, я бы посмотрел какой ты крутой оклейщик. Мне кажется, такой плёнкой, что ты работаешь, инвалид с одной рекой на коляске без правого глаза справиться.

[@estebanvelazquez161]

Will not buy that film, I'll stay in with vvivd

[@lockystocky1]

Stay away from this product like the plague. Buy cheap buy twice

[@royresendiz3611]

🤓👍

[@billyp333]

You video ok but your sound not correct. .....

[@commandershepard9338]

Its look like chinese Fivestar wrap...no, fivestar better)))

[@martink.9442]

Film looks bad. Surface looks bad. Cheap but worthless.

[@shadowblack1987]

Garbage vinyl lol...