What you need to turbo your G6 engine

[@scottyhankemeier9380]

Does ARP 207-4201 head studs fit the Mazda B2600i G6 engine? What is the best aftermarket head casting you have found?

[@zippityzbrake]

Super excited to see more on this motor

[@Meia1122]

Thank u for this video Man. I was gunna swap the engine out. But now this is all I need

[@r32gtstroh]

Great video! Where did you pick up the oil feed and coolant flow for the turbo?

[@InspiredExistenceAustralia]

our turbo is only oil feed which we get from the side of the block just below the head

[@julianalderson3938]

Takin the g6 an drivline to new limits. Like it

[@julianalderson3938]

Yer ive got a brav. Think power later mine feels very low geared n screams but gos no where. Like it but yer gearbox n trans is very short for me till 5th. Not sure how strong they are after turbo. Like diffs n stuff but risky id say. Bit love it cheers

[@rolandechoin8903]

what tye of gear box goes well with the g6 petrol

[@YouareGodsAnointed]

how much power do you get with this setup

[@julianalderson3938]

Yip good just find my bravs tryin to skid in first powers there just built for up hill utility. Rekon tirbo be cool bit just skid alot. But if thats it sweet as.

[@PHATT13_DADDY]

when can we expect to see the turbo g6 in action?just some short clips will do man I have a similar setup in my courier keen to see how urs goes 🤔 great job with the build she's clean az👍

[@InspiredExistenceAustralia]

We are about to release a video of it within the next week or so or it driving and performing

[@REVY01]

@@InspiredExistenceAustralia do you know how much horsepower these engines can make with performance parts installed naturally aspirated and do you know where I can get performance parts like forged pistons and valves etc.

[@scottyhankemeier9380]

What's up with the salmon built designs website? Are you in Australia? Do you know are they still selling G6 engine products and the dial it in ecu?

[@minibass07]

Could you get in contact with salmon built designs ? After a exhaust manifold

[@marty3469]

​@@minibass07not sure if he's still making them, I bought a exhaust flange from him 18/ 24 months back on eBay and it took a couple weeks to get sent. I built my own 4 into 1 turbo manifold and works great .

[@minibass07]

Thanks for the reply@@marty3469. What head studs and head gasket are you running with the turbo?

[@marty3469]

@@minibass07 mine is all stock until it breaks, I don't rag it to much and it's all stock internals from a recent rebuild before I bought it. If or when it does burst I'll swap a Honda k24 turbo into it

[@giannigrasso912]

just curious to know what the steering wheel hub is that you have used. iv been looking everywhere for one that fits

[@InspiredExistenceAustralia]

no idea its what it came with when i bought it

[@giannigrasso912]

@@InspiredExistenceAustralia by chance do you have a way of contacting who you purchased it off?

[@InspiredExistenceAustralia]

@@giannigrasso912 No mate i dont have the contact

[@zippityzbrake]

Rx7 hubs work, but theres a shoulder on the back side that the truck wheel doesnt have. Shave that down so the horn contacts the new hub

[@zippityzbrake]

Ballpark on the cost for all this? Im planning on buying a crate motor and building a motor for boost from the bottom up. Want to price it all out

[@InspiredExistenceAustralia]

You will have to contact a mechanic and or tuner to help with that one as there is a lot to cover so best to contact the professionals, its not a cheap exercise thats one thing we can say.

[@TinZeng-n6v]

Hey mate, would all of these mods be applicable to the 2005 2.6l bravo?

[@Knowlsy0]

yep

[@concernedaussie1330]

Super awesome.

[@nik557]

What gearbox do you run after turboing it?

[@InspiredExistenceAustralia]

The standard 5 speed will hold from what we have been told upwards of 300hp if driven properly

[@chadbeets9852]

What studs did you use for this?

[@InspiredExistenceAustralia]

I was lucky to have ARP head studs already but they are hard to get so you'll have to do some research

[@chadbeets9852]

Do you know what length or what car they came off? Seems like the 4g63 m12 studs might fit

[@JuanCarlosMartinez-ys2gg]

@@InspiredExistenceAustralia Ive been trying to find head studs for my truck, from what car were the head studs that you used?

[@scottyhankemeier9380]

Camon you gotta have some info on head studs.. Do I just have to send a bolt to ARP to get custom Studs? Someone has to have some info. ARP part numbers etc..

[@travispoulsen8958]

Did anyone find studs??

[@MrLunithy]

My new guide for my FORD PD 🤣

[@Super_Stan]

not sure but it is recommended you have a bottle to pop and are also ready to get slizzered

[@rlaxson89]

Wonder if all of this is the same as my 91 b2600 🤔

[@InspiredExistenceAustralia]

if its a b2600 there the same engine so the products on here can work

[@rlaxson89]

@@InspiredExistenceAustralia even it being a 91? That would be sweet. What mods would need to achieve 10-15 psi? I mainly want the blow off noise lol

[@InspiredExistenceAustralia]

@@rlaxson89 The mods in the video will give you what your after to have it reliable and sound awesome but to save cost you can just go a turbo setup with the wastegate actuator included so no external wastegate its cheaper

[@markmiranda4838]

gonna boost mine it over heated and im gonna boost it to see how far it goes lol then if it blows buy a new one lol first gonna slap it all together see it runs lol

[@juliomorales5581]

Completo presio del motor$$$$

[@Krisjoverovovejovovichtski]

fly like a g6

[@InspiredExistenceAustralia]

Certifiedprinting.com.au

[@eternalerudite1758]

someone add this up for me please in cash dollars

[@InspiredExistenceAustralia]

You will be looking at around 6-7k with everything in the video, obviously depends of labor cost and what products you actually get