Wheel Hub Assembly - 2006-2013 3.5L Chevy Impala

[@whoami7566]

Aside from chrisfix I have yet to see anyone else than you guys and him to have such a detailed and extensive video while still straight to the point. You cover so much but it's all useful. Definitely subscribing and liking. Amazing content guys.

[@LemurMonitors]

We learned from the best! kzbin.info/www/bejne/rKKWc6mLhJ6Xf5o

[@davieboy1970]

You forgot to mention that before you put on the new wheel bearing you should Use a grinder or sandpaper and clean the hole where the bearing slides into and maybe put a little bit of grease on it to make sure that the bearing goes in there straight

[@richarddarbyshire7896]

Thank you for going over all the tools needed. Very professionally done.

[@josephthomas9052]

Right! We shade tree KZbin mechanics need all the help we can get.

[@TheLuckyJuan]

note to who ever does this, when you’re hammering the hub, if you hit the dust shield you will bend it and it will rub against your rotor so don’t think it’s your new bearing making that scrapping noise when you drive, just take the wheel off and grab pliers and bend the shield away from the rotor carefully.

[@hhectorlector]

This tutorial had way more style than most mech vids. Well done!

[@LemurMonitors]

Thanks!

[@JonStratford1234]

Excellent video. Thanks for posting it. Appreciate the dry sense of humor. "Cover up your shiny new wheel hub with a rusty old rotor...much better."

[@LemurMonitors]

Wouldn't want it looking too nice!

[@FLIHI818]

You can also rotate the wheel to left or right.... your welcome!

[@dtnel]

Good video series especially for those who don't know how to do them. It's good to see someone showing younger people with simple steps that they themselves can do it as well. I do all my stuff and also do repair so I was just seeing if they're was much difference and you guys are pretty much spot on!

[@charlestownsend4380]

Nice video but the pulley puller is not needed I've replaced dozens of hubs on these cars and all you have to do is hit the brakes really hard in reverse right for you do the jobs and it puts opposite pressure on splines of the axle and that usually makes it come free

[@RudyvanBree]

So before you take the caliper off you loosen the spline nut and put the car in reverse then hit the brakes? That will un-seize the spine from the hub? I will try it. I tried a puller with the bolts still in the hub to loosen the spline but no luck. I am getting a hydraulic puller to see if that will loosen it but this may be a neat trick.

[@sizzlin321]

I had to use a 20 ton hydraulic gear puller when I replaced the hub on my Impala. Made sure to put a California liberal amount of anti-seize on the splines when I put the new one on.

[@bobm7275]

But it's that one time, and your one car is up on stands.

[@bobm7275]

@@sizzlin321 don't ever get a Cali. mechanic to do the work, all you will hear is but it was rusty so it took four hours.

[@jp0921]

You guys rock. Step-by-step leaving zero guess work for me.

[@jdhitc]

Yours and 1aauto are the best videos iv found to help me with my cars. I feel you two should work together.

[@PREACHERMANN2003]

This REALLY helped me get the job done! Saved me hundreds of dollars, just took some time. THANKS!

[@MoDodgeMoMods]

You just saved me 15% on my mechanic bill..tks for the great video.

[@rickodean7238]

Thanks for the video. I used it when replacing the hub on my '09. One useful tip, the ABS sensor cable needs to be on the side closest to the mounting hole on the splashguard, not on the bottom. Yes, I was stupid enough to torque everything down prior to attaching and checking the slack. Hope I don't ruin anything when I take it back apart. Another issue I had was getting the axle out of the bearing. Tried my bearing puller but really did not budge. Had to use an air hammer to get it out. Last item, the fastener holding the disc on was a T30 bolt. Important to know since many Torx bit sets only go up to T28.

[@LemurMonitors]

It's a miracle we got it out so easily, this thing did a lifetime of duty in salt/slush.

[@user-of4eh8mu1t]

done 6 of these this month... not one of the came off with a few smacks of a hammer. Wheel bearing removal tool needed to ease the removal.

[@toddandrews2967]

Repair shop wants 600 to replace my hub, i will do it myself now,thanks for the detailed video

[@shawnpa]

I always enjoy the videos, and this really helped me out. I agree about that aligning the caliper bolts can be very annoying. I've had 10 minutes of hand scraping pain doing. The knuckle buster avoidance tip, and all explanation was excellent. Thank you.

[@dungeonmp3]

You guys are gonna have to pick up busch or budweiser to sponsor you with free beer :) Great video and thanks for the share. Will be sharing this in an impala group online.

[@JohnnyRingo1863]

Good video! Valuable information it's going to help me when I replace my hub and bearings I'm tired of getting bent over at the mechanic shop every time I go it's ridiculous anyway thanks guys sorry for the rant 🤗

[@8307c4]

Very nice video, I absolutely just did mine with just this video as instruction: I want to add that I definitely used a gear puller, a 4 lb hammer (heck with that rubber mallet thou I had that too), 2-3 different chisels / punch sticks, PB Blaster, Carburetor / Brake Cleaner, compressed air, Anti-seize compound and some steel tubes to extend the ratchet for better torque (some of the nuts / bolts require over 100 foot-pounds)... The axle nut came off with a 1/2" pneumatic gun, compressed air tool that is. I'm not convinced that it's a true 34mm, that is the socket I used since that's what the instructions said but I felt it was loose on the nut. No busted knuckles, I may have said a bad word but it wasn't out of control and I'm not even sure I went there thou I did have to run out mid-job to purchase 3 new bolts since mid-video they instructed NOT to reuse the old ones... Kind of miffed they wouldn't include these in the kit to begin with, even if it costs extra... The old assembly came apart inside the wheel, all the electronics were stuck in there, had to punch and pull these out piece by piece. Oh and a floor jack to lift the car up in the air, to tighten the axle nut back on I started the car then wedged a steel extension between the brake pedal and the seat so as to hold down the brake while I tightened the nut... They said 150 ft.lbs. but I got it as tight as it would go and that is that. Here's the video I found extremely helpful: kzbin.info/www/bejne/qpqyqaOlbNKfopY

[@bamahammer3660]

This is one of the best videos I have seen in a long time. Everything is laid out step by step including the torques. Good job guys.

[@LemurMonitors]

Nothing more worse than when they go "torque them up and done!"

[@bamahammer3660]

@@LemurMonitors I agree.

[@notq7123]

Thanks for the video. You just saved me a bunch of dollars. Best video of 4 videos. You had the torque specs!

[@dtnel]

Great video. A good addition to the series for the 99-06 range Impala and Tahoe/Suburban/Yukon and Denali series would be Power Steering Pump Diagnosis, Flushing, Replacement and Bleeding of the system which can all be done affordably for the DIY'er..... Timing Belt and Water Pump Kits along with Thermostats on Toyota, Hyundai, Honda and other like brands along with water pump replacement on Dodge Dakota Pickups and other Dodge Pickups as well. Keep up the great Vids.

[@0315rwalker]

I’ve watch a lot of different videos, so far I like your video guys, good job and thanks for the tips, keep them coming

[@edwinmcnew4389]

Awesome! Poor Chris! He did all the work!

[@LemurMonitors]

Right??

[@randal1470]

Great vid guys, thanks! Just fyi, my 06 impala, as well as one other I’ve worked on also 06, had a 1 5/16” spindle nut, as opposed to 34mm.

[@mathewjohn1749]

My caliper bolts were 18s not 15 as well but otherside it was a good video

[@josephthomas9052]

Very detailed and informative. Budweiser is the reward

[@gregmccorrister4061]

Excellent video 2 👍🏾👍🏾 up. I'm glad you tell the people the torque specs.

[@jacobknelsen1613]

WOW!! AWESOME VIDEO AND INSTRUCTIONS!! THANKS!!.

[@LemurMonitors]

NO PROB!

[@gregl2249]

I’ve watched 10 of these videos and they all give different torques on the same exact car

[@llg7456]

By far the best video EVER! I think I can do it!

[@GuitarHipp0]

I'm so jealous of how you were able to loosen the axle nut so easily, I've been at for hrs and it won't give

[@redred7136]

Spray with pb blaster first. Makes it easier.

[@johnnyschannelofhope2260]

I can't figure out what's wrong with my Impala that has the traction ABS everything keeps coming on but I don't know what if it's the front or the back I love your videos watch all the time

[@danmccurry3810]

Great DIY video yourself, good detail with safety tips and humor!

[@LemurMonitors]

Thanks!

[@johnrogers7243]

What about when pressing on my brakes and the whole car shakes? I have replaced the rotor, brakes and calipers. I noticed that one of the calipers guide pins jams up. I have read that it could be a warped hub. Any way I am replacing these tomorrow. This video gave me all the torque's.

[@RailFanRob]

nice video...i'm about to do both the left and right side on my impala...

[@nickheinz3737]

Good Video; can believe you put that old rotor and caliber on that new hub!

[@LemurMonitors]

That's a video for another day! .. of course with winter coming it won't be long before the new ones look the same way

[@nilloc93]

"cover up your shiny new wheel hub with a rusty rotor" i'm dying lol

[@travisscott4675]

You'll helped me ... I'm thankful for your channel

[@robinmurray9801]

Informative vifeo but Instead of beating the caliper on why didnt you compress the caliper pistons?

[@laneesha1000]

Sooo detailed thank you! I’m going to try myself! However I don’t know how to torque HELP😩

[@LemurMonitors]

A good torque wrench goes a long way, they're pretty easy to use - set it to the desired torque (instructions should say) then keep going until it clicks.

[@valancebohm3204]

@@LemurMonitors will the wrench say the measurements. Does it have settings

[@RicersRUs]

Valance Bohm yes it will have selection

[@bryanmay6578]

Wait why did you have to press the brakes while torquing the axle nut?

[@joalbade908]

UM, one thing I noticed *missing*..there's a T30 torx bolt that tightens the rotor to the hub assembly(one of the three holes inside the circle of the wheel studs).From the condition of the rotor/rust in those counterbores, I'm figuring this is a boneyard example(nbd), and the original was snapped on a previous brake job(they sieze badly>so pb ahead of time). w/o it, might be annoying judder you can't track down. just a suggestion

[@mboaz4730]

Our car had a screw holding the axle in place, no need for the gear puller. But we did destroy three of our 13 mm sockets on those bolts on the back.

[@jeffchristianson-ziebell]

AWESOME VIDEO THANK YOU!!! Literally the best on the subject on KZbin & by pros not jokers who THINK they know - it’s basically perfect I did this on my 2010 exactly as shown no problems! How ANYONE could thumbs down this video is OBVIOUS proof there will always be the tiny few who can NEVER like anything theyre so miserable LOL.

[@thejasonofrosses2243]

Forget a beer. I need some shine and a doobie. This thing was tiring, as I had run of the mill equipment lol

[@plaid11]

Blue Fast Forward hope you at least had a breaker bar

[@brandonGCHACHU]

TRQs repair video for this job says 118 ft lbs for the axle nut and other videos say 140 or 125 lol. Kind of wondering what the actual torque spec is

[@so_chi_chris]

I like how you explained the process as you were going and named every part as you removed it.

[@LemurMonitors]

Thanks!

[@peteshovels5277]

Is there a wire for non ABS vehicles?

[@attila7092]

Okay so I've never used a torque wrench before. You say it can be set for different pounds?

[@martinsanders7817]

When Chris cracked the beer. Had me laughing

[@MichaelMusicOrr]

Love you guys! Lol love the humor in this one! :P excellent work!

[@yeyoduarte3338]

The sensor cable means the abs?

[@stevenkurinec4194]

How long has this car been sitting? In use rotors don't look like that

[@LemurMonitors]

We actually live in a climate here that has a lot of salt and moisture in the air. We are located on a island and salt water gets blown into the air regularly. Due to this we see rust build up on rotors like this in days. If my personal daily sits over a weekend and there's a lot of rain and wind I can feel the rust on the rotors. Its just something we live with.

[@johnnys1027]

Would it be bad if I put a little wheel bearing grease into the gears before sitting in the new wheel bearing?

[@mrtwister9002]

Very instructional. Great video.

[@jamesreed7358]

Great video guys ! Keep up the good work. ;)

[@ironhorse1224]

good video explaining details on replacing the bearing, thank you & Happy Holidays..

[@LemurMonitors]

Thank You!

[@curtiscarey580]

What is the torque on the rear hub bearing assembly on a 2012 Chevy impala LTZ ❓

[@DIY-dv7xj]

How would u brake the axle nutt without messing the wheel bearings up ? Ik u didn't explain cause y'all are changing the hubs just courios

[@jackfenn7524]

When it comes to instructional fix-it videos, this is the crem-de-la-crem, the Nobel prize winner, and the best of the best in the world. Nothing could be made clearer or easier. I have been quoted every price from $500 to $238 to do this. You make it seem easy and I'm sure that it is, now that you have demonstrated it so fantastically well. You deserve the Nobel Pizza Prize for this! (Best if eaten while still hot. Not recommended for wearing around neck!)

[@LemurMonitors]

I'll put the nomination papers together!

[@whackamoles]

Since not to reuse old bolts, what are the thread/depth/material for the new 3 13mm bolts? Would be nice to have all parts before getting car off the ground.

[@davidjones-vx9ju]

buy them from auto parts supplier by manufacturers specs

[@DarthMasiah]

thanks. so easy a bonsai enthusiast can do it 👍

[@stewartjohnston3975]

Fear no fix!! Love it!

[@farealwitit7947]

Awesome vid. Its beer 30 everyday son! Lol

[@RFlash-xc4lo]

I have a 2013 Impala I've been scared to jack it up from the aluminum sub frame. Has anyone done this and bent the sub-frame?

[@craigsabo5035]

Did it right did not see shred lock for any bolts saw three vidios that put three lock blue on every bolt and torq them what's the point

[@BeautifulWolf1987]

Genuine question and could really use some advice: I have a 2011 Chevy Impala that needs the front left hub assembly replaced. But when I took it to my mechanic, he tried all day to get it off and couldn't. He said the splines were fused due to heat build up from the bad ball bearings inside the assembly, and it would need a new axle, steering knuckle, AND hub assembly to repair it. Is there any kind of way that the assembly can be broken loose, or am I really going to have to have a super expensive ($600-$800 due to front end alignment) repair? I would really appreciate some helpful advice because I don't want to get rid of this car. Thanks!

[@qman1434]

How did you make out?

[@LA2047]

Best words I've heard all day: "Now that's a man's tool." lol

[@wesleywideman7185]

Question why doesn’t this 34mm socket fit on this axel nut on my 12 impala?

[@wesleywideman7185]

Never mind deep-well duh🤦‍♂️

[@ironmike7601]

Well done video I appreciate!

[@kevinwilliamson7294]

I have never had a wheel bearing come out that easily.... And you say you did not prep this prior? Hoping the one I have to change comes out like that. Good video by the way

[@LemurMonitors]

If it helps, we *were* planning on cheating. We had a torch and a hammer and a giant gear puller then it just.. came out. I wouldn't believe me either.

[@kevinwilliamson7294]

@@LemurMonitors I changed both of the wheel bearings in about 2 hours!! They actually came off with just a tap from the hammer!! Couldn't believe it!!

[@mikebodoe6172]

easy solution take off strut bolts then its a straight shot just pull hub flat then your looking down at it. easy peezy @C Hansen

[@robertbaker50]

Is this about similar compared to a 2018 impala?

[@shanebryan8151]

Thanks guys, I thought I was supposed to leave a little play on the axle nut. Opps lol

[@Кикомкд]

For 2010 chevy impala Lt Axle nut torque specs?hub Bearing moog from ebay. Thanks nice video

[@LemurMonitors]

155 ft-lbs

[@kwekumanu1340]

MY 2008 chevy impala LT has no axle nut. makes everything confusing.

[@Randomness984]

I didn't know Murr from Impossible Jokers was a mechanic too.

[@57BAwagon]

What brand of bearing hub did you use? There seems to be a lot of choices out there.

[@mobes329]

I bet it was from Rock Auto because from another video where Chris said that he has a lot of magnets and Rock Auto gives out magnets with every purchase.

[@missingremote4388]

I used the cheap replacement front hub bearings. Driver side, Lasted only 1 year. Now today, I ordered A/C Delco. ( Mabee I over torqued the center hub nut)...🚗

[@oscarmonreal2538]

Is the hub what causes the car to shake? Mine feels loose when I move it. I want to replace today if possible. Just need to go get a couple tools. Can you please respond as soon as you can? Been like this for a couple months and it’s getting worse.

[@LemurMonitors]

It could be - if you feel a shimmy (if it's the front it could be worse when on the brakes) and a rumbling/roaring that changes with speed it's a likely culprit.

[@amrohussamful]

if you forgot your anti seize at home , you may use some engine oil

[@zaydogg]

How long do these things usually take?

[@LemurMonitors]

Book time for a shop would be around 1 hour, but if attempting on your own, we'd recommend planning for double or triple that!

[@kingj1615]

Do you have any videos on how to replace a fuel injector on the same vehicle?

[@LemurMonitors]

Not yet, but a good one to add to the list!

[@soroushsepahyar]

How can we know if the issue from harness wire pr the hub itself?

[@alainsuarez6535]

The best mechanics

[@KristaNicolee15]

No wheel speed indicator on the 07 chevy impala, and star nut on the rotor to remove it, just for anyone who might need that extra guidance.

[@hypnotist19]

What size star nut?

[@JOHNRMECH]

Why don't you mention upfront that new bolts and axle nuts are called for?

[@FerminelHacker]

Best video ever. Thank you very much.

[@LemurMonitors]

Thanks!

[@bobbywhitehead9881]

Thank you guys. 👍🏾

[@mikelawler474]

Any ideas on a good brand of hub? Amazon has the cheapest, some with good reviews... but I'm skeptical! For those who have replaced lots of these, which ones last and/or do you recommend? Thanks in advance!

[@zrafferty]

Mike Lawler go with moog or other high name don’t use cheap you will regret it

[@CEEJAY_305]

06 Chevy Impala SS CV Axle video ????

[@syknoobwoo]

The socket to remove nut from axle on my 08 is 33mm, not 34.

[@LemurMonitors]

What trim/motor do you have?

[@j.r.rickett1431]

My 08 Lt 3.5 is a 34mm

[@syknoobwoo]

@@LemurMonitors 3.5 LT the flexfuel

[@bakerreed1173]

I just broke a breaker bar trying to get the axel nut off ... what now .

[@webguy79]

How long is that break bar?

[@oscarmonreal2538]

I have my car on jack stand and the wheel moves a little bit. Does that mean it’s the hub that’s bad

[@oscarmonreal2538]

Also removed the tire and the hub wiggles a bit

[@UFOzNoJoke]

(Crickets) ... 8 months later Yes. Most definitely.

[@timrob_showtell1771]

This was a awesome ghetto video lol yall did good but dude said "I'm here ☺️👍🏼" lol

[@adamnombrano7225]

I hit a board on the freeway and my wheel on driver side and now my wheel wobbles. I had a mechanic change wheel bearing but it worse now. Paid this guy 600 dollars and problem is still there. Any advice would be helpful

[@RicersRUs]

Adam Nombrano sounds like a broken tie rod.

[@john12892]

155 ft-lbs? Where did that number come from? The Haynes repair manual has it listed at 118 ft-lbs.

[@LemurMonitors]

MOTOR specs say 155 ft-lbs - there seems to be some disagreement out there however depending on where you look.

[@john12892]

Well, I got to the bottom of this mystery. It's 155 lb-ft if you are using a new axle-nut and 118 lb-ft if you are using the old nut. Also, not sure why I typed it up as "ft-lb" in my first comment. But thanks for the video, regardless.

[@mikebodoe6172]

118 lb-ft never heard of this before but makes sense. thanks, as for help getting hub out I use an old rotor reverse installed so you can get a good hit on it with big hammer. Be careful it flies out and will hit you in the knee..@@john12892

[@missingremote4388]

I may have over tourqed the center nut. Because I re- tightened it a year later after I installed the cheapest hubs on eBay. Mid March 2019. Hub just went out yesterday...28 may, 2019 Hummmm

[@orangeslice7257]

videos well done and helpful

[@misterrightfix4129]

Job well done! thank you so much for sharing, I truly appreciate it, good luck with your channel.

[@LemurMonitors]

Happy to help!

[@Shelbyproductions]

My 2009 goes in next wed

[@LemurMonitors]

Good luck, watch your knuckles!

[@awm7353]

How much torque is needed to make Chris smile?

[@LemurMonitors]

kzbin.info/www/bejne/gIGanYaQit2Cetk ^^ This much