BMW Motorcycle TFT with Nav VI and Headset setup and use.

[@marcouellet]

I was able to connect everything as indicated. One thing to keep in mind. The volume for phone calls is a bit lower when channelled thru the TFT, than a direct iPhone to Helmet config. My setup: iPhone X, GSA 2018, Sena SLR, NAV 6. Also, I thought it would be useful to add the steps in your video description, as it's not always possible to watch YT on the field! Here they are (let me know if I made a mistake!) 1 - Update all devices to the latest firmware - Phone - Helmet COM System - TFT System (BMW) (Latest version as of 2019-03-23: Version 001_019_180) - GPS (via Garmin Express) 2 - Reset (erase) all Bluetooth connections - Phone (ICC6.5in + COM + GPS) - Helmet COM System - TFT System (BMW) - GPS (NAV - Garmin) 3 - Pairing devices in this order - Pair Headset (Helmet) to the TFT using Primary Phone Connection - Pair Headset (Helmet) to the GPS using Secondary Phone Connection (or GPS) (Enable Headset, Enable Media) - Pair iPhone to TFT (BMW) (Allow Contact sharing to TFT) - Pair iPhone to GPS (Don’t allow Contact sharing to GPS, Disable Phone calls, Enable Smartphone link, Enable Media) - Pair Intercom Helmet to Passenger’s Intercom helmet

[@aMAYSingLife]

With your permission add this to the description. Thank you

[@marcouellet]

Health4ADV For sure!

[@aMAYSingLife]

Also, remember that when you do the phone through the Garmin, volume is controlled both by the Sena AND the Phone. So if you have the volume down on the phone it will max sooner than it would if the volume is max on the phone. @@marcouellet

[@cliffordfowler8231]

marc, I'm not having success in registering my VIN to the App .... keep getting msg that vehicle is not equipped for Connect Drive....what am I missing?

[@cliffordfowler8231]

Oh my mistake....just discovered I downloaded the wrong BMW app. arrrrgh. sorry

[@AncientAviator]

I've been watching KZbin "how to" motorcycle repair and operation videos for years and rarely begin a project without first searching here for advice. My hat's off to the gentleman that produced this highly professional video. It's THE single best "how to" video (covering a VERY complex subject) that I've viewed in fifteen years. In short, it's SUPERB. BMW should pay this gent for the work HE DID in explaining their equipment operation that they DIDN'T EXPLAIN for their customers that have purchased BMW bikes with the new TFT display and BMW Navigator GPS. I sent this link to my local BMW dealer telling them shouldn't sell another TFT bike without providing this for their customers. I consider myself fairly technically savvy. Accordingly, I was extremely frustrated after several failed attempts at getting my helmet BT headset, BMW Navigator VI, iPhone 7 and BMW TFT to work together on my new 2018 BMW R1200GS. I watched several KZbin videos and NONE solved the problem. Then I came upon THIS video. BINGO! Problem solved. Nice work sir. Thank you SO much for producing this!

[@aMAYSingLife]

I truly appreciate your comments. I actually did both the explanation and the production and editing so I thank you for your thoughts.

[@AncientAviator]

@@aMAYSingLife I took a ride yesterday afternoon and had a lot of fun trying out all the apps you recommended. Much fun! The only issue I haven't been able to resolve is the volume of the BMW Navi VI in my CARDO headset. No matter what volume I have the Cardo headset set on, the BMW Navi route instructions are FULL VOLUME...as in PAINFULLY LOUD in my headset. All the other volumes...media, etc., is fully controllable with the headset volume control. The BMW Navi VI settings says the volume is controlled by my headset...and says to adjust it there. It seems like I'm stuck in a do-loop on this. Any thoughts? Thanks again...Jim.

[@aMAYSingLife]

@@AncientAviator you can modify how loud music is and gps instructions are in the "mixer" portion of audio control. this way you can have audio at full volume and gps and much less.. we used to call the "pull up" lady in airplanes bitchin betty... same applies on the garmin on the bikes lol.

[@AncientAviator]

@@aMAYSingLife Thanks very much for your speedy response. Yes, I flew Hornets in the Navy and know Bitchin' Betty all too well! I got yelled at a lot by her. Could you please tell me where the audio control/mixer function is found? GPS...TFT...Cardo Helmet Control firmware? Thanks again!

[@AncientAviator]

@@aMAYSingLife Disregard my earlier question please...I found the audio mixer control page under "Volume" on the BMW Nav VI. And as you probably suspected, it was FULL UP for the GPS. That would explain the ear shattering volume I was getting. Thanks so much again for all your help! Nice job!

[@cede108]

Greetings to America, this is by far the best video explaining these topics that you can find on the web. Completely incomprehensible that the manufacturers do not see themselves as responsible here! Many thanks from Stuttgart/Germany from a 1951 guy with about a million motorcycle kilometers! Kind regards, Christoph Dimter 👍👌😀

[@aMAYSingLife]

Means a lot coming from a vet moto man like yourself.. thanks so much!

[@martinharrison8291]

Even though this video is 4yrs old it is still very relevant today. Thanks for the step by step. Definitely worked with my 2023 gtl 😊

[@aMAYSingLife]

Glad it helped!

[@elansinger]

This is absolutely amazing. Starting a fire with two wet sticks would be easier than trying to navigate the connectivity between all of these devices/apps without this video. You rock!

[@aMAYSingLife]

Lol I tend to agree with you!

[@KeithLowe-x6r]

I want to thank you for creating this informative and professionally narrated step by step tutorial. I have referred back to it several times over the last few years when I needed to refresh and tie all the elements back together. JOB WELL DONE.

[@aMAYSingLife]

Glad it was helpful!

[@dperique]

This is one of the best instructional videos I've watched (e.g., no annoying background music distractions, etc. but packed with very useful information and actual screen shots). I admit I was put off by the length but within a minute, I see there was a lot of good content. I'm only using a Connected Cradle unit but this video helped me understand the complexities and why some things don't work and possible sources of bluetooth confusion related to priority, etc.. Thanks for keeping the video on point and focused and excellent job.

[@aMAYSingLife]

Thanks so much! I hope everyone who makes comments including yourself realizes how much it means to those of us who produce videos.. it’s much appreciated

[@deancorey9978]

3 years later and still very helpful!

[@aMAYSingLife]

Glad to hear it!

[@stevebibby4667]

4 year old video and still an invaluable explanation! My 1250GS is currently in for its first service but after riding round on it for a month I still hadn't figured out how to get things working properly. I have the connected cradle which I think introduces some limitations but armed with the info from your video, I look forward to trying it all out once the bike is back! Thanks for taking the time, excellent work.

[@aMAYSingLife]

using the connected cradle it will be slightly different than connecting with the nav VI. You will connect the phone directly to your Sena in phone 1 slot, and the bike TFT will be phone slot 2. It should be a more stable connection since you are taking out the Nav VI. I am curious if they have eliminated the vibration issue for phones. I had heard it was damaging some. have you not had that issue?

[@stevebibby4667]

@@aMAYSingLife I have read some of the reviews about damage to iPhones but I have the X, in the leather Apple case, it sits in the cradle secure enough and I don’t notice any vibrations on the screen…perhaps like the fella falling off the building, it’s just a case of so far so good ;) I got the tft firmware upgrade as part off my service yesterday so all my current connections were wiped when I picked up the bike, I connected the sena then my phone to the tft ( which took an age btw) as it was a cold night I didn’t bother messing with the cradle and just headed home, planning on setting up the cradle in the morning so will report back. Reporting back...works a treat, thank you sir!

[@GB-818]

With all respect Sir you should have asked for some money... 😊 this is the best tutorial to connect all devices properly. It works perfectly fine. Not even a BMW Dealer was aware of this way to connect the various devices - and being from Germany, I have plenty of them around me. Again - thank you so much - so detailed so well explained this is just outstanding! 👍🏻

[@aMAYSingLife]

GB 818 I really appreciate that... that’s the life we live now though, hard to get paid for something the tops dont event understand how bad it’s needed until it’s out..

[@luivan2]

of course Garmin paid him, top recommendation is to update from nav V to VI thats money for them :-)

[@aMAYSingLife]

@@luivan2 actually Garmin didn't pay me a dime and I paid for my Nav VI just like everyone else.

[@DarrenBaptiste]

Excellent tutorial. I was a bit worried about the length, but it was exactly as long as it needed to be, without any filler. I appreciate the time and care taken to create the text slides, and the overall approach to explain not just the How, but the Why of it all. Great job!!

[@motocato]

yep, agree completely

[@ChristopherDoyle-s5g]

Thanks for this! I would not have been able to pair my bike, nav, and phone without this video. Manuals just didn't cut it.

[@aMAYSingLife]

happy it helped after all these years!

[@JESSIFONTANILLA]

I have seen a lot of riders having problems making their headset, TFT and Nav VI work together. On my GS 1250, Nav VI, and Sena SRL Neotec II with your instruction as mentioned in this video everything works well. Nicely done. Thank you very much.

[@aMAYSingLife]

Thanks for sharing

[@AndrewPetrieNZ]

This is the best tutorial for setting up my comms that I could find. Thank you. I have not read through the comments, so it may have been mentioned already, but I found with my Cardo Freecom 1+, after connecting to the TFT on the Primary channel, I had to turn the TFT (bike ignition) off, before it would let me connect the Cardo Secondary channel to the GPS.

[@aMAYSingLife]

Yes, I have been testing a Cardo for about a month or so and intend to release a video specifically for it. There are some slight modifications such as what you mentioned but overall its very similar. It should be noted until I updated the Cardo it marginally did anything correctly based on my video so updating is very required..

[@colmdoherty49]

Best video on this topic I have ever come across by a country mile thank you

[@aMAYSingLife]

Wow, much appreciated!

[@markwebb4538]

Excellent video and a giant thank you for continuing the Q & A here. My setup: 2020 GS, Nav 6, Sena 50S, iPhone SE (2nd gen - 2020) all on the latest software. All works as it should except phone calls. The phone makes/receives calls and the phone identifies the sound source as ICC6.5, but I can’t hear the caller and vice versa. If I leave the Nav 6 off phone calls work, but then of course the Nav 6 does not. I’ve looked for various volume controls, but I’ve either not found them or they don’t exist. As a secondary, but smaller problem, the Nav 6 directions come through choppy. For a test, I used my wife’s new iPhone 12 and the results were the same. There’s so much potential here…. Thank you for your service to the rider community.

[@aMAYSingLife]

1. Is the nav setup to use Phone 2 slot or is it using GPS slot? Should be Phone 2. 2. In the settings on the nav under bluetooth, uncheck Phone from the checkmarks and see if that resolves. 3. What happens when you change the audio selection to be Nav on the phone instead of ICC6.5 for sound source? 4. Is audio multi-tasking turned on on the 50s. 5. Is HD intercom turned on - needs to be off. 6. regarding choppy - where is the phone located - insure its close - not in your pocket in your jacket. place in your tank bag with as little restriction as possible. It would seem they used the crappiest bluetooth radio possible on both the nav and the TFT. 7. Do each of these individually and test your results each time. I'm throwing ideas not necessarily edicts. please let me know your results. The Sena 50s hasn't been the device we were all hoping for.. I was really hoping for one that had a much better processor in it so it could handle some of these complex connections a bit easier. Not sure it did that. Let men now and good luck!

[@markwebb4538]

Re #1 - how do I tell which slot is being used? Re #2 - already tried that but did not help Re #4 - how do I verify audio multi-tasking is on? Re #5 - how do I verify HD intercom is off? Re #6 - phone usually in tank bag I'll try all your suggestions as soon as possible and report back. Thanks!

[@markwebb4538]

Found answers to 4 and 5 in the manual - apologies for not checking there first.

[@markwebb4538]

@@aMAYSingLife Sorry to take so long to get back, I work at a CPA firm and tax season just ended. Per suggestion from Brandon Wren and raffa650 I tried tuning on the audio multitasking option. It all worked!! Steps I took - 1) followed your directions for resetting everything, 2) connected Sena 50S to laptop and via Sena app turned on audio multitasking, 3) followed your directions except the resetting part. Now a question - I believe doing a factory reset on the Sena 50S returns the audio multitasking setting back "off", which then puts me right back into the problem, so is there a way to reset the Sena 50S and still have audio multitasking set on "on"? Thanks!!

[@aMAYSingLife]

@@markwebb4538 "delete all pairings" doesn't change the settings... A "factory reset" would so you dont want to do factory reset once you have the settings the way you want them but there is a method to "delete all pairings" and this is the best way to insure you don't accidentally have something paired the wrong way.

[@petrspacek3316]

Well done for it. The BMW dealers in Czech republic have no clue how to do it. Now thank to you my and my friends are now well happy.

[@SuperXenophile]

Thanks!

[@aMAYSingLife]

Glad it helped!

[@paradox-chimera8461]

Thank you sir , I have a GS 1250 and just buy a Schuberth c4 pro with sc1 advance system . You have make my life really easier . Thank you to spend time too help other riders . Very clear vocal as visually,a clear tutorial for everyone . Much thanks 🙏

[@The230dirtbikegirl]

By far the VERY best connection tutorial found anywhere. A very huge thanks for sharing your expertise and helping me maximize my investments in my bike and tech accessories.

[@aMAYSingLife]

Thank you sir..

[@nelwan9051]

A superb video, thanks so much. First time I did everything correctly with the exception of unticking the phone call option on the Nav. As soon as I took a phone call, the phone dropped offline from the TFT. Re-watched the video, picked up my mistake and it connected perfectly. Thanks again for such a brilliant tutorial… Regards Nel

[@kevinmcdonald1970]

Superb tutorial ....after months of trial and error this worked for me first time !!!!

[@jarrodsimister14]

Omg. (don't often use that) I've had a bmw for 4 years, and always given up with the nav 6. Now I have tft and you've made it all work. Thanks a million 😁❤️👍🤗😢

[@aMAYSingLife]

Great to hear!

[@gregsherman1]

This is such a good tutorial video. Not the first time I’ve watched it. Perfectly sets up my bike/comm/gps. Thanks!

[@simonliddell8183]

Many thanks, after being frustrated with the constant re connecting of my headset to the tft, now all works perfectly 😁. Great video

[@KhunJH]

Thank you for the time spent to make this video in great detail. I had some difficulty in completing it, and after many, many repeated deleting all the connection history in all of the devices and starting over, I was finally able to get everything to work as described, however. I have the ‘19 R1250 GSA, 20S EVO, iPhone 8 and Nav 6. All have the latest software versions. Headset to TFT - worked perfectly as you described Headset to NAV 6 - after holding the Jog Dial for intercom pairing, I needed to give the Sena a moment before I tapped the phone button. iPhone to TFT - worked perfectly as you described iPhone to NAV 6 - worked perfectly as you described Everything works....phone calls, media/music, NAV directions. And thanks for the “mixer” settings of audio, I can individually set volume limits for phone, music and navigation.

[@daviddedman7429]

Fantastic video. Bought a brand new Packtalk Bold and now my GS is totally connected by following you’re step by step guide. Cheers!

[@aMAYSingLife]

David Dedman I’m doing a review of the bold with the bmw and everything worked great until I connected a Sena headset. I discovered music was choppy, just couldn’t handle the load. If I turn off music from the nav part it solves the problem. Have you noticed this? Do you connect to other Cardo units? Does it all work when u use dmc? Trying to get some real world before producing the video

[@daviddedman7429]

WheelSpin Productions hi. Only thing I have noticed is when you get a NAV prompt, when the music comes back on it stutters for a couple of seconds. Also worth note is that the mic is very sensitive and if too close to your mouth, it won’t like you using a loud voice. I whisper ‘hey Cardo’ and it now works!

[@bradleyjsmithod]

Thank you. I just got a PackTalk Bold and had not been able to connect to the TFT and phone in a way that allowed everything to work. This protocol straightened it out!

[@aMAYSingLife]

Happy to help.. thanks for watching..

[@ianjonesmusictuition6716]

Sir!! I have been having a bit of a struggle with the Tft, Nav 6 Galaxy S8+ and Sena 20sevo. I'd decided to just pair the Sena to the Nav for simplicity as on tour I like to have the nav instructions. However after watching your video I will attempt to sort it correctly! A shame BMW themselves seem to have no idea how to achieve success with this system. Many thanks for producing this.. Ride safely.👌

[@aMAYSingLife]

Ian Jones Music Tuition thank you so much. Very appreciated. Good luck on your setup

[@dano9176]

Thanks for the walkthrough. My setup is now working perfectly. Note that the TFT FW/SW has been updated and the current version is 001_019_180.

[@aMAYSingLife]

Dan O thanks for the note. I'll update in the notes.

[@graemebrown5540]

Fantastic video, still relevant after 3 1/2 years. Well worth the time too watch the whole thing, don't skip ahead, and it helped me get everything (F750, Sena 10U & SF1, iPhone, Nav 6) all talking to each other. The only problem I am having is that the instructions from the Nav are at max volume, the volume control on the Nav is disabled and the Sena volume doesn't seem to make much difference either. Have tried both 2nd Phone and GPS pairing, both the same. If I could fix this it would be perfect.

[@aMAYSingLife]

Thank yo for that.. you should be able to go to the mixer on the nav and control how loud navigation instructions vs music is.. you are saying that doesn't work for you?

[@graemebrown5540]

Doh! Forgot about the mixer! In my defence, when you try to adjust the volume on the Nav the screen says “Use the controls on the headset to adjust the volume”, so I did. Thanks for the reminder

[@mikemerrill175]

Incredibly well presented. On my way to the garage to tune things up. Marc Ouellet's summary is very helpful also

[@aMAYSingLife]

Thank you

[@maartentietge9662]

Thank you so much for this tutorial. I use a Schubert C4 plus Schubert/Sena SC1S (fw 2.0) on a TFT, also have the Navigator VI. Had a hard time setting this up properly, until now that is. Took the time to sit through your entire tutorial and it was well worth it. As you say, just take the time now to understand why everything connects the way it does, and you'll save yourself time in the future when you need to reconnect everything, for instance due to a firmware upgrade that erases all settings. I had volume problems before (too low on phone, BMW Connected nav and media). These problems seem to have disappeared after I operated the different sources, and made sure the volume setting on the iPhone was on max. Everything connects without a hitch, and making and taking calls from the TFT is a breeze. Not sure if the volume can be changed through the TFT. Using the jog/dial does not seem to make a difference. Many thanks again.

[@atlwrns7127]

Thank you a lot for this great video. Never got Music from my phone and phone calls to work properly on my Neotex SLR headset and watching this video makes me realise why. Thank you so much for making this great video, must have taken many hours to do so. But it is very much appreciated.

[@aMAYSingLife]

Glad it helped!!! Thanks for watching!

[@peterwbaker]

Just been pointed to this, nice and clear, instructions worked perfectly with my Gen 2 S1000XR TFT screen, BMW Nav VI and Schuberth SC1a... a BIG improvement! If there was a way to have the phone default back to connecting with the helmet when the bike was turned off that would be the icing on the cake:-) but I don't want to confuse the devices until I know the above is stable... Thanks, Peter

[@HomeTheatreEngineering]

First of all a massive thank you. This must have taken ages to put together. I am sure like many others I really appreciate this video, the way it was put together and the help and clarity it has given me. THANK YOU SO MUCH. Here in July 2022 with the latest updates( unless I missed it in the video) I found I needed to select the media source in the Nav6 to Bluetooth then I got audio. I also had issues with media not activating on the NAV6 I would select and enable it but it would be off next time. Maybe this is fixed now I set Bluetooth as media but haven't checked that. The only thing I miss is the voice control function I have lost to my phone. I also realised I need to turn my phone volume up to get enough level so that I could control it with the TFT. Awesome Job :-)

[@aMAYSingLife]

Thank you!!

[@HomeTheatreEngineering]

@@aMAYSingLife You are welcome as someone who has a KZbin channel I truly get how difficult and time consuming this is. I bought a brand new F850GSA on Friday and you are the man who put the grin on my face. Thanks again!

[@tckeys8855]

Thank you!!! I could tell that the Sena connection with the phone was going to fight with the NAV and TFT. Had a feeling we would head down that road to disconnecting the Sena from the phone. Your video was EXACTLY what we needed.. Everything works now. My only reservation with this set up is that if I come off the bike and I'm laying in the ditch and the bike is across the road in the other ditch and electrically broke, I can't call 911 directly from the Sena. With the direct Sena connection, I could press the phone button and voice command Siri to dial 911. That is the reason that I quit using the phone mount on my bike. If I come off that thing, I want the phone in my armor jacket with my torn up body. I have a huge amount of songs in my phone. I am wondering if the play lists, artists and such will ever sync and if so, how long with that take. All things considered, it is a nice system. I just came from a 2016 GSA with hybrid analog/digital dash and I'm just configuring the new 2023 GSA. iPhone 13 Pro/BMW Nav VI/Sena 50S/2023 R1250GSA

[@aMAYSingLife]

I personally dont trust that my phone will make a call after an accident. The new Iphone 14 has crash sense so if it is still able to make a call then it might do it automatically for you. I use an inreach device that is always attached to me for that purpose. i can push the sos button with gloves on. That said, 911 could easily be faster if you are in urban environment so your point is valid. If you off your bike as a result of someone else then likely someone else will be calling as well so there is that. if i'm out in the middle of nowhere then my phone wont likely help anyway. if phone is on you, then removing gloves and hitting the emergency response is likely best bet. Thats assuming you can remove gloves. Its a guessing game where all that lands in an accident for sure. I've totaled 2 bikes and had 3 accidents. 2 of the 3 times i had no cell service.. the 3rd was due to a car pulling in front of me and i t-boned him. he called 911, not me.

[@MG1776-t9p]

This was the only video that I found that explains the process in a detailed and accurate manner! Excellent, sir. Thank you. I found my Neotec II/Sena SLR/iPhone XR connection to be spotty for music. It cuts out every few seconds. Have not root caused, but I suspect BT and poor design and quality control naturally.

[@aMAYSingLife]

Marshall Guillory it’s possibly the slr that is the culprit. Not the first time I have heard that from that model

[@TheMotorradRider]

Thanks so much for all your time and effort that went into the making of this video. Extremely professional, well delivered and very informative. I have the latest firmware on my 2018 GSA and have been struggling to get everything working as it should. The Australian dealer has absolutely no clue whatsoever (instilling little confidence for getting problems sorted out in the future) so amidst much frustration, went searching on the good old “interweb” and came across your video. Viewed from start to finish, you made perfect sense and the subsequent setup on my moto was easy and painless. I have two helmets that use different comms systems, a Schuberth C4 with built in SC1A and an Arai XD-4 with Cardo Packtalk Bold. I set up both of the helmets up as per your instructions prior to pairing my iPhone XS to the TFT and then the Nav VI. Turned everything off after each pairing and BINGO! Everything working. Voice commands from the Nav VI through the helmets, media, phone calls, the lot. Your instructions showing the feature set of the BMW Connect app are extremely useful as well as the various little tricks of Garmin Smart Link were likewise extremely helpful. Again, many, many thanks for your efforts. If you ever want to take a trip down to the good old land of Oz, feel free to drop me a line.

[@aMAYSingLife]

The Motorrad Rider thank you for your appreciation. It means a lot. I would love to take you up on that offer someday.. have always wanted to go there!

[@TheMotorradRider]

Health4ADV. Feel free to keep in touch. There is some seriously good riding down this way.

[@robbevear6733]

Thank you, that is the most comprehensive KZbin clip I have seen on the Nav 6, well done.

[@aMAYSingLife]

Rob Bevear thanks

[@beemersix9782]

Although I thought I had pretty much figured out how it all works, I still came across some very useful tips. Thanks a lot for making this video!

[@brandon_wren]

Again, your video comes through! Just got a new iPhone 13 Pro and had to redo my setup with a 2021 R1250GS Rallye and Sena 50S. Worked the first time! Thanks again, sir.

[@aMAYSingLife]

Great to hear...

[@raffa650]

with my 50s it doesn't work. iPhone 11 updated, tft updated to July 2021, Nav 6.I don't hear cell phone calls. How did you do it?

[@aMAYSingLife]

@@raffa650 I believe audio multitasking has to be turned on if it is off by default, hopefully Brandon will share what he did. If you want to make those type changes either plug it into your computer and configure it or pair it with your phone temporarily to get the settings done then pair that slot to the bike after you have it configured.

[@brandon_wren]

@@raffa650 Are you running the BMW Connected app? Can you hear music from phone thru TFT to Sena? Make sure you enable all permissions so you can see your contacts and call logs ON the actual TFT.

[@raffa650]

@@aMAYSingLife Multitasking audio is disabled. Now I try with enabling.

[@marktcoleman]

Best overview ever, thanks for taking the time to walk through this.

[@dreamrider2956]

Excellent.. bought the 2019 R1200 GSA and THIS is what I needed. TFT Nav 6 10S Android 20S Sena Wiped and started over a few times, yes, speed was my problem, Works like a champ when it's done. THANK YOU Thank you

[@bsebesty]

Me too. Many THANKS!!

[@ironhorsegladiator5034]

Thank you, not even the dealers know how to do this!!

[@gassanshaladan8711]

The best video I’ve watched in a while. The level of detail was really impressive. Thank you for making this!

[@qdllc]

Sad that the manufacturer fails to address these issues. BMW’s manuals are not very user friendly.

[@nestorperea1277]

Not only the BMW manual but the Garmin and Sena instructions. All three should stop being self serving and reach out across technology borders to help customers out. We customers spend a hell of a lot of money on these products. Listen to your customers!

[@That_Paul_Guy]

I went through this setup as you described in the video and it works, but it’s quirky. I seem to have the best luck by turning on my SRL first, then the bike. It then takes around 30 seconds or so for my iPhone XS Max to connect to the TFT. The only issues I experienced were between the phone and TFT. Mainly, using the Amazon music app, sometimes the music was playing on the phone and I could see it on the media screen in the TFT but there was no audio in my helmet. Turn the bike off and back on, all the connections start happening and it works fine. I also discovered that you turn the volume up or down with the phone rather than just relying on the SRL by itself. I appreciate you taking the time to put this info together.

[@aMAYSingLife]

The Cranky Biker make sure you are running latest rev of the firmware... the earlier versions seemed to be slow to connect. You likely have already done this but worth repeating.

[@That_Paul_Guy]

Health4ADV latest rev of firmware for the SENA? The phone is what takes the longest to connect. The SENA is pretty fast and is on the latest rev. I think I may blow it all away though and start over. Those BT connections can be finicky, as you know.

[@aMAYSingLife]

The Cranky Biker I was actually meaning the TFT when talking about insuring latest firmware. There was a rev that was bugged and it took forever to “wake up” to pair. A good test is on the TFT go to settings then connections when you first turn on the bike. It connections takes a long time to become active that’s your problem. Until that is enabled then nothing is going to connect to that bike because the radio isn’t even active yet.

[@That_Paul_Guy]

Health4ADV I’ll have my first service done next Sat and will ask about updating the TFT firmware then. I assume that’s not something I can do myself.

[@aMAYSingLife]

@@That_Paul_Guy no unfortunately its a process and can take a bit of time depending on the update. Good Luck!

[@josdijkstra5937]

Thanks immensely for your help with setting this up correctly. I was stumped and you made it all so clear !

[@BartAssink]

Thanks for helping a bro out! Great efford whent into this vid. I reconnected the TFT to the (i)Phone as the last device gets serviced first. Making Spotify connect to the TFT and not the NavVI when playing screaming guitar solos and bending natures laws (i wish)!✌🏼

[@amaysinglifellc6273]

Happy it helped!!! Rubber side down! Throttle to the back!

[@PeterBellemans]

A downloadable PDF slide-deck would ‘upgrade’ this awesome video from 99% to 100% ☺️

[@aMAYSingLife]

I can totally do that... great idea.. Not sure how fast I'll get to it but I will get it done..

[@listentothat1]

@@aMAYSingLife After all this has been connected, what do you connect the pillion helmet to

[@aMAYSingLife]

Nigel Jennings still connect it the same way you would if it were bike to bike. I have not recently changed my theory on this based on newer tft firmware but connecting the headset to the tft has not proven useful. I have seen when activating intercom to pillion that the nav seems to freak. If that happens turn off the phone portion but leave the rest. That should help.

[@listentothat1]

@@aMAYSingLife thank you for your reply, I,m a newbie to this, just purchased a new f850gs, and a nav 6 with sena 20,s x2 but it's not going well, going to have to delete all and start again

[@dgweez]

Super helpful. The smart link from phone to gps was what I was looking for. Entering destinations on the nav 6 is cumbersome at best. Entering one destination by itself takes about as much time as this whole pairing dance takes. looks like we have some of the same riding playgrounds since I’m in North Carolina-

[@aMAYSingLife]

What I wish you could do with smart link is enter an address from a long way away (not around you) and it work. This seems like a silly limitation that would allow me to utilize the smart link far more often than I do. As it is, you can only enter locations that are within x miles of you. At least that has been my experience.

[@robhill6859]

Thanks so much for this video! I couldn't work out what I was doing wrong but thanks to your step by step advice on the sequencing it is all working as it should now. Excellent tutorial!

[@aMAYSingLife]

Thanks so much. I'm glad you found it useful!

[@Uteone]

Thank you for your video - it’s helped me move my setup from intermittent Bluetooth connections, so much so that I usually didn’t even try to connect my phone/TFT etc when I went out on my bike, to now everything working as it should. Again, thank you - much appreciated 🙂

[@aMAYSingLife]

Great to hear! I'm finding that is pretty consistent with a lot of people. Glad it helped!

[@pablomaresca]

Thank you very much for this super extra useful tutorial. You’ve done an amazing job. Too much effort to clearly explain al the set up. I’ve watched several times and have made notes in my iPad and then realized you have written them down in your post. 🤦‍♂️ Thanks you very much!

[@aMAYSingLife]

You're very welcome!

[@MrKerryjd]

Thank you so much for the amazing comprehensive instruction on this video. This has helped clear up so much confusion when trying to link everything to the Nav and TFT. Something I’ve never been able to achieve successfully You deserve a medal sir! Thanks!!!

[@theFatLebowski]

guy, these kind of videos are golden, thanks for this

[@aMAYSingLife]

I appreciate that!! Hoping to get several more done soon. Thanks again!

[@tonynguyen1761]

Thank you for tutorial video, I followed the instruction and everything worked but phone call was unable to communicate then I unpaired headset to NAV and it works. Again, thank you for the tutorial video. Just watch your video on Cardo with TFT and you mentioned Sena does not have power or bandwith to connect with others and I have to agree, mine is doing that, too bad I can not get direction from the NAV VI but I guess I have to learn to live without. Thank you Dave for the info

[@bobwolff68]

FANTASTIC Instruction. Long, but necessarily long. I'm super glad to have found this. Can't wait to give it a try after updating all my firmware!

[@Carlnewman68]

Thank you for your step by step to connect all up with my new gsa , your a star and it worked clockwork , carl , from uk

[@aMAYSingLife]

Glad it helped!

[@davidlambert5008]

A big thank you . I couldn't connect my cardo. now it's all good . you're a star 👍🏾👍🏾👍🏾

[@internationalsixty1819]

Newbie to tft and nav6, learnt loads from this. Thank you!

[@fonso1961]

Brilliant video I've just connected my 30k as you did it works brilliantly, hardest thing was trying to watch your video whilst doing everything at the same time lol. Thanks for the help. Alf.

[@andybeviere541]

Absolutely brilliant thank you❗️

[@petrkosek3373]

TX a lot. It helped me very much.

[@Vusseyv]

thanks very much!!!! this worked for my new ‘21 GS, bmw fit for all comms (sena 10r) tft, and zumo xt. although the menus and prompts were slightly different it was similar enough. shame i can’t control tidal from the zumo, only the native iphone music functions. but hey ho. haven’t tried siri from the headset yet. anyway great video. top man.

[@aMAYSingLife]

thank you .. much appreciated.

[@vitogiacalone8044]

Amazing presentation, finally I have got everything works seamlessly! Thank you !!!

[@aMAYSingLife]

vito giacalone very appreciated

[@NotesofNate]

This is like studying for test for a class I might take in a school I haven’t yet been admitted to. Lol. I’m looking forward to getting a 1250GS and Nav VI at some point!!! Great video. Thanks!!!!

[@aMAYSingLife]

LOL, yeah it can get more complicated that it honestly should be but that's the world of bluetooth unfortunately.

[@mistersubby]

Thank you very much. Without your help I couldn't do it for sure. Bye bye from Thailand

[@Reduxalicious]

Great video! And still works for a 2023.

[@aMAYSingLife]

I have been surprised how little has changed myself

[@vfroger]

Thanks again. I attended your presentation at Pandora's and this is a nice summation of what you covered that day.

[@aMAYSingLife]

Thanks Roger, I'm glad you enjoyed it!

[@TheGeoDaddy]

Definitely worth the Winding/Time on a road like the Skyline - where the scenic road can take HOURS longer than the highway straight line... and you don’t wanna ride thru a national park with Wildlife jumping across the road esp in the dark!

[@i.c.y.]

Thank you so much for this instructional video and all the additional information. This is really, really appreciated!

[@aMAYSingLife]

Glad it helped!

[@analogstyle]

Fantastic video! Thank you so much for taking the time to create this. Would love to see a video on how you incorporate the nav systems and the REVER app. I’ve been making custom maps on BaseCamp, with some level of success. I haven’t really figured out how to share them on other devices. I just downloaded REVER because of your video. Can’t wait to dig into that app. Once again thank you for putting the time and professionalism into your videos.

[@KEITHSMITH-ew4je]

Brilliant video - problems all solved!

[@aMAYSingLife]

KEITH SMITH glad it worked for you!

[@ReflexionesMoteras]

This is the best video on this matter!! Thanks

[@aMAYSingLife]

Thank you!

[@gijsborsboom2161]

A great and very clear explanation, thank you! I was about to buy a new headset as I thought this was the issue for streaming audio, but everything works perfectly now. Thank you!

[@aminbazdeep6417]

Hi at Health4ADV, thanks for this post. Well at least I think I mean thanks however I did not get very far into the video before my brain was fried. I have just bought a F750 GS with all of the gubbins. Nav V1, TFT, Scala Q3, mobile phone and to be honest I am struggling to cope. As and older guy I am more into the comms aspect than speed (but lack the technology ability) I was beginning to think that I had made a major mistake with this combo. You have absolutely floored me with this info. I may not live long enough to be able to learn all of this stuff. Anyway I am gonna try my best and keep practicing. Thanks for taking the time to prepare and post a video like this for the "hard of thinking" it is appreciated even though it has overwhelmed me somewhat. Take care out there.

[@aMAYSingLife]

Good luck with your setup. You have a great machine and perhaps just need a little help to get it setup. I would suggest providing this video to the dealership where you purchased your bike and ask them to help you set it up. once you have done it a few times it doesn't take but about 5 minutes to set it all up and get it going. Pandoras Motorsports here in Chattanooga sets them up for their customers all the time. Good luck my friend..

[@aMAYSingLife]

Did you ever have any luck getting your bike setup?

[@aminbazdeep6417]

@@aMAYSingLife Hi H4ADV. Not yet bud I am still offshore not home till the 28th. I am following your instructions and noting them down. However having a Scala Q3 and a Samsung means there are some issues I will need to resolve which differs from your set up. Getting stressed just thinking about it.

[@aminbazdeep6417]

Hi H4ADV I have had an element of success in that I can link my Scala Q3 / Samsung A3 with the TFT and Nav V1. I get all of the instructions from the nav but I cannot get my music to come through the nav, yet. I have also just upgraded my phone which I am assured is fully up yo the job. I also intend to upgrade to a Packtalk Bold. I have your blog on a constant loop at the moment (and need it) Thanks again for your time and patience on this blog. The "hard of thinking" much appreciate it.

[@stefanuhle6831]

thank you! How you made the Button for the Active Radar on the navigator Screen (21:26 min) ? Thnx

[@aMAYSingLife]

You can customize what you want the two buttons to be. I believe it is in settings but I have since sold that bike with the nav 6 so I can’t test that

[@autokennerblog]

@@aMAYSingLife Thank you. I found ist later yesterday.

[@GB-818]

Very well done - thank you so much - extremely well described easy to follow... will try this asap. I will need to upgrade from smh10 to Sena 20evo or 30k. Update: I did upgrade today to the Sena 20sevo - works absolutely perfect and exactly as you described! Also the GarminSmart App is pretty cool.. As I do not have MP3s stored on Navigator 6 I changed the settings and removed the media option. Now I’m listening to the music from my iPhone or even Spotify from the TFT 👍🏻

[@aMAYSingLife]

I personally can't recommend the 30k.. Its been a pain for me and I have even sent one back and the mesh still didn't work properly. Not sure if there is interference with the TFT and nav and it just can't handle mesh with all that connected or what, but unfortunately I don't feel the 30k is fully baked.. 20s evo or the 10c Pro (camera which I am using now) work well.

[@gabrielgomez6057]

Excelente video. Muchas gracias. Claro y preciso. Saludos desde Colombia. 👍🏍

[@aMAYSingLife]

Thank you to those from Columbia! I'm glad you enjoyed the video.

[@drsleepdog]

Exactly what I've been looking for!

[@aMAYSingLife]

Glad it helped you!

[@AlastairT00]

Thank you for taking the time to explain this

[@aMAYSingLife]

Glad you enjoyed it

[@stevematthis3199]

Great video. Picking up GSA this week. Well done.

[@scottjayson72]

How do I enter a location in the Garmin SmartLink app that is not nearby? Thank you so much for all of the AMAZING information you have provided us with!

[@aMAYSingLife]

unfortunately unless they have changed this, I can't figure out how to do it.. It would be soooo much more useful if this simple feature was added.

[@scottjayson72]

@@aMAYSingLife Thank you so much for getting back! I found that if I pick a destination in Google Maps, click share, I can then select the Garmin SmartLink app and send it to that, and then off to the NAv VI 🙂 I am THRILLED at this find!

[@aMAYSingLife]

@@scottjayson72 thats good to know! I don't typically use google maps so hadn't tried that... thanks for that tip!!

[@issamelsayd]

Thanks man, incredible information you share with us

[@demzunoplayer]

The Sena has an earphone socket that helps in the set up without the need for wearing the helmet. It saved me a lot of time and mucking about.

[@martinkerr8343]

Brilliant tutorial thank you!

[@JIMMYSBN]

works also with sc1 advanced from sena (Schubert specific model) thank you a lot dude!

[@dpendleton525]

Glad to hear that. I was concerned that the SCHUBERTH SC1 only supported Bluetooth 4.1 rather than the 4.2 recommended in the video. So, you have connected the NAV six, TFT and Schuberth SC one with iPhone with no problem? What TFT software version do you have?

[@josemariacelma6989]

Un millón de gracias !!!

[@kkif2001]

Your help is tremendous. Thank you for a perfect, detailed and really helpful video!!!

[@aMAYSingLife]

Grateful it helped you!

[@edwardhaughey4732]

You’re a total pro. Nice work 👏

[@aMAYSingLife]

Thank you sir.. much appreciated..

[@huseyintuter]

Thanks same topology works with 2022 yamaha Tmax tech Max. It has similar kind of TFT. I don’t have garmin device but it TFT supports native gamin app on your connected phone and you mirror the garmin app on your TFT and control it.. Therefore I am connecting 2 different iPhones to TFT one is for media and using apple maps and Google maps second one is for yamaha link app, native Garmin connection to TFT, And phone calls (+ music ). The connection method is works the best as you mentioned thanks for posting

[@aMAYSingLife]

Wow thats good to know that other manufacturers have determined the "hub" method is the best option.. So maybe we will see a bit more standardization among manufacturers forcing SENA and Cardo to think differently as that would solve some issues depending on how they are designed as well. Thanks for watching!

[@qnapmussi3350]

Hello! Many thanks! It was the best video about this I could find! Helped a lot! I have managed to improve your solution though...: My suggestions: (1) Before anything alse and with the TFT and Nav VI turned off, sync the two Sena 20S intercom systems, (2) execute your original steps, (3) add the second rider´s intercom to the TFT but as a secondary phone on the Sena, (4) if you want to, add a second phone to the second rider´s intercom as a first phone. DO NOT share music from one Sena to the other. The music sharing is done by the TFT while the communication between riders is done through the Sena´s system. It seems that everything is working with everything without issues so far... Good luck!

[@aMAYSingLife]

I have not ignored this post but have been traveling so much I have not been able to test what you have recommended.. Is the purpose of adding the second riders 2nd phone to TFT in order to share music through the TFT? I think that is what you are saying.. This would be nice.

[@qnapmussi3350]

@@aMAYSingLife Not necessarily, but could work if you do not connect it at the same time to the TFT. The original idea would be to allow the second phone to also be available for the passenger...

[@aMAYSingLife]

@@qnapmussi3350 I think it was an epic fail to not allow the TFT to provide intercom between rider and passenger.. what were they thinking.

[@nickfogg4831]

Wow great informative video, even though I use the Packtalk Bold I set up the same but did not know about not letting the nav6 have control of certain things while pairing I just said yes to everything, I will re-do mine now to see if it works any better. Thanks again for taking the time to feedback on your findings cheers, Nick

[@flyjets01]

Thanks for taking the time and explaining this so well !!!

[@scottc3]

Really great and informative video! Just need to fly you over here to the UK to set up my new bike! 😉

[@aMAYSingLife]

Scott C pat the flight and I’m on my way lol!

[@lucabonardi6068]

Grazie ottimo tutorial

[@Amsurf1]

Many thanks for the video! It would have taken me many hours to figure out this connection sequence. Unless I’ve done something wrong the only down side I see with this connection sequence is that I no longer have voice recognition which made it very convenient to place calls, Presumably this is because the phone is not directly connected to my 20S headset.

[@aMAYSingLife]

Mark Miscione no you did it right. Unfortunately we lose access to that feature when we set it up this way. Glad you enjoyed the video

[@Amsurf1]

WheelSpin Productions Thanks for the reply! FYI, went on a ride today and everything worked well as far as music and calls are concerned. I need to spend more time with the Nav and apps to get the most out of them. But pretty happy with the ways it’s working!

[@frankrafferty660]

Fantastic information, just what I needed, many thanks.

[@SwabianBiker]

Well done, thanks for sharing your excellent descriptions!