In this video I will show you how to remove and replaced a White Rodgers Zone Valve
Пікірлер: 22
@bennyrubio72432 жыл бұрын
Alex thank you so much for this video im glad I found it and followed all the steps. God bless brother
@alexthehandyman34942 жыл бұрын
Hello Benny, IM so glad you liked it. Wait until you see the other white rodgers video. You ll love it. It is on how to troubleshoot, wiring, sequence of operation et c.
@raulescobar38813 жыл бұрын
Thank you very much for making this video!!! You’re a lifesaver and the video was very well done!
@alexthehandyman34943 жыл бұрын
Hola Raul Thank you Im glad it was useful to you., Thanks for subscribing. See you next video
@miguelmateos98282 жыл бұрын
Alex do you know how I can replaced the zone valve white - rodgers model f109181 I appreciate your Advice I take out the head but the bottom its so hard to take out
@tonyjuneau11 ай бұрын
Thanks dude!
@jziggy46313 жыл бұрын
Very helpful. Thank you.
@alexthehandyman34943 жыл бұрын
thank you Ziggy. I have part B of this video Is about wiring and troubleshooting. Go to Alex the handyman Thanks for subscribing
@esaamawshana1018 Жыл бұрын
Good job thank you for showing that
@midwestteediamondhands5460 Жыл бұрын
Thank you
@l.a.m76452 жыл бұрын
So when installing new valve does the dial have to be in open or closed position?
@R0am3r2 жыл бұрын
It doesn't matter if the valve is open or closed. Just make sure the control aligns properly so it fits properly. The control knows position of the valve from the alignment.
@geraldross94309 ай бұрын
You mentioned the thermostat wiring and did not illustrate or show the back of the stat?
@alexthehandyman34949 ай бұрын
kzbin.info/www/bejne/iHeUo6KMh5V_a80si=6E3oOguqKH9pKQk3. Hello Gerald. The video you just watched is about how to remove and replace the power head. Look at this video it has greater detail on wiring and thermostats
@timdubois92983 жыл бұрын
great job
@paologanci44622 жыл бұрын
Do I have to drain the pipes before I remove the valve
@alexthehandyman34942 жыл бұрын
Hello Paolo, Turn the boiler off first. Hopefully you have shut off valves before and after the valve. If not, shut off every valve you see in your system. All of them! We want to avoid draining your system. Be ready to collect water off the valve when you remove it. If you don't have shut off valve then just remove (relieve) some pressure by draining just a little bit off water from the boiler drain. After you replace the valve make sure you add water to the system until it reaches 12-15 lbs of pressure (your feed valve should do it atuomaticlly, Also you might have to bleed air out of your system. See my other videos. Good luck . let me know how it goes. Thanks
@paologanci44622 жыл бұрын
@@alexthehandyman3494 thank you Alex you saved me lots of money thanks
@alexthehandyman34942 жыл бұрын
@@paologanci4462 Glad to hear that., Thanks
@jett77777713 жыл бұрын
Good till it came to wiring you should have shown what wire goes to what number on zone valve “
@alexthehandyman34943 жыл бұрын
Hello Cash Money.. this was about how to remove and replace. I have another very detailed video on wiring and troubleshooting. go to alex the handyman
@epluribusunum54058 ай бұрын
Either that or you can look at the instructions for wiring 1311 and for that model 5 is power at all times. And 4 opens when it makes call for heat. And six closes when it opens energizing 6. Therefore your 3 wire. Using a certain type of thermostat for 3 wire.spdt thermostat. So 1 would be always 24 v neutral and 2 24 v hot from the transformer. Refer to wiring instructions.