Willys Valve Seat Cutting and Parts For Sale

[@GAZIS4]

It's a pleasure to see such nice tools....we have old Sioux, black and Decker vibrocentric and super expensive German Hunger...nice job Brian!

[@gregoutdoorsman4598]

I enjoyed watching the seat cutting. I’ve never seen it done before. It’s amazing how that’s just a hand crank on the cutter 🤯

[@nakiajames6226]

does this make the valve sit lower in the head, or does it sit at the original height? I just want to know if the valve would need to be modified

[@timlambert7155]

I learn something new with every video.

[@metalshaperJeep]

great, that is why I make videos

[@j45acp69]

This is a great video! Thank you for taking the time to educate everyone on this process. I know in my current project i'm just getting ready to build my block (L head), and I will be using this information although I'll be using stones.

[@metalshaperJeep]

Grinding stones work fine, just take your time and make sure everything is concentric.

[@XXcaesar5000]

thanks for sharing It's funny my wife thought it was odd Shawn Hannity was into jeeps!! lol you sound just like him

[@metalshaperJeep]

Thanks for watching!

[@stevewarren3051]

Great vid. If you don't get a centered lap line on the valve, how do you polish out the line so you can re-lap it after you re-cut the seat?

[@ShercoBill]

Thanks Brian,lots of information in this video

[@jasonlay9414]

Hi Brian, I was wondering about the valve contact ring width. Are you concerned about how big or small it is or just that it’s in the middle of the valve face? Enjoy your videos. Jason

[@metalshaperJeep]

Yes, the width is a factor as well. Most important though is location,...... should always be in the middle of the valve.

[@GeeenJ]

i always lap the valves in regardless of how good the seat cutters are i've found in the past that not lapping them in they tend to not seal as well

[@metalshaperJeep]

I always lap valves as well. Neway has done extensive testing and says that after the valve seat is cut with their cutters the valves do not need to be lapped. I still always lap them though, just like you.

[@TheOriginalUberGoober]

metalshaper neway is dead wrong. Always need to be lapped. Always.

[@jbpost52]

the focus was blurry on displaying the center of the ring on the valves. How wide of a band are you looking for on the valve after lapping them?

[@mikeashford9240]

Thank you I am use to seeing stones being used that was great ....

[@greggelder4013]

Hey Brian I've been an automotive machinist for 45 years and enjoy watching someone not only do a proper job but teach others how to do the same thank you and how much for the Keeps her hood and fenders?

[@greggelder4013]

Jeepster damned spell check

[@metalshaperJeep]

Hood is gone but I do still have fenders. contact me at [e-mail] if you have any interest. Brian

[@TradIrishHarper]

The cutters for the L-Head were #205 & #622. What size pilot guides would you use for the L-head? Cannot seem to find a kit out there that is for the L-head, but maybe I am overlooking something. Great video.

[@lawrenceaiello8654]

Just seeing this Brian. Do you still have the combat rims? Love the valve Job class! Thanks!!

[@vwivancc]

Does the valve seat cutter was sold? Thanks

[@American_Jeeper]

Brian, I absolutely love the education I get from you, as well as watching the practical application, but the visual was brutal on this one. Does your camera not auto-focus?

[@nategcole]

What a great series! Pretty amazing the tolerances on these older engines. Do you know if these tools and techniques were used on rebuilds, say, in the '60s (for a '50s block)?

[@metalshaperJeep]

Yes, these cutters have been around for many years.

[@ronbz455]

Where is the cheapest I can get that gauge? I have seen big money.

[@bannereddivpool]

Will these work to bore a new hole for the seat to be pressed in?

[@metalshaperJeep]

no you need a proper seat cutter to get the job done with square sides and the proper diameter.

[@bannereddivpool]

Recommend any tools for this job?

[@bestenginejdm1543]

Do you sale these cutters. I need for Honda and Subaru, can you help with

[@bbboymoonton142]

Saan tayo maka beli nito ser,

How do valve seats get out of round in the first place?

[@metalshaperJeep]

High mileage, incorrect valve adjustment, poor fuel, and just the repeated pounding they get from many miles of use.

[@lmiranda441]

Where cam I buy the valve run out to

[@metalshaperJeep]

Goodson Engine Building Tools has them.

[@nitinlohar7213]

Hi sir I am interested to your ston grinder

[@luisfelipesoares432]

Sou brasileiro como consigo esta ferramenta

[@metalshaperJeep]

newaymfg.com make and sells them. Brian

[@jeepsofjt7797]

Hey Metalshaper! Which pilot do you use on the L heads?

[@metalshaperJeep]

.374" on intake valves and .375" on exhaust valves

[@jeepsofjt7797]

@@metalshaperJeep Thanks for the reply.

[@luismercado7563]

How much you charge to fix the block ?

[@metalshaperJeep]

depends on what the problems are, each block is different.

[@mohammedazeem2867]

How to buy neway valve set cutters from India please tell me

[@metalshaperJeep]

you can buy them directly from Neway. check out neway.com and order them .

[@حبیبکریمی-ض7ث]

سلام ببخشید چرا به زبان فارسی ترجمه نمیشه؟

[@TheOriginalUberGoober]

Your concentricity is out because of the new guides I would suspect. Now if you were using old seats I doubt you would be off .020. Just in my experience. Anytime guides are replaced the concentricity is off. That’s because guides never go in exactly as they came out. This is why every time any good shop changes guides they should cut the seats like you did. These Neway kits you would think are made of solid gold though lol.

[@jimhoran5445]

Thanks Brian!

[@حامدالنجاشياتلمجاشي]

كم سعر هاذي العده

[@gibamec7636]

Very good job, master.

[@metalshaperJeep]

Thank you kindly

[@nakiajames6226]

great video

[@fomaakvinskij9124]

NEWEY only for the repair of such prehistoric motors

[@sandrobahry2558]

As you are one of most dedicated and traditional Willys rebuider in the world, as I can follow up in this channel, I strongly recommend you do not try to give it up of your tools.

[@vittalpujari7366]

Valve seat Beat cutter petrol engine

[@LuisRodriguez-kz7cg]

Great video what kind of play do you have to have on valve guides Before you change them

[@erniecothran3112]

Do we really need a Inventory before the story. Really

[@metalshaperJeep]

If you don't like my videos don't watch them and try to find the information I put out on other channels. Good luck.

[@ronbz455]

Take it off right away and show how it's off!!!!

[@haledmondson2756]

For those of you who have wives with teeth congratulations on her training,and just use her teeth brush....Hal