Windstar Lower intake gasket

  Рет қаралды 73,396

jonreyna

jonreyna

Күн бұрын

Пікірлер: 37
@toecutter1978
@toecutter1978 5 жыл бұрын
Thank you for posting this repair video. This one and the other two that deal with the manifold have really helped me understand the nature of the repair I need on mine.
@sandracruz8686
@sandracruz8686 3 жыл бұрын
I learned a lot today from your video, I just suscribed and the reason is because midas is charging me ALOT of money for changing my lower gasket and YOU just showed me that the money might be worth it. Thank you I was very curious to see what exactly am I going to pay for...
@sandracruz8686
@sandracruz8686 Жыл бұрын
Good morning, I just wanted to update you on my Windstar, so I changed the gaskets myself😁thanks to you I saved $800 but then everything else started going wrong, my car feels like she's gonna cut off it's as if she can't breathe, I cleaned the throttle body even tried the seafoam but now I have oil in my coolant but no water in my oil, weird huh🤔 just wondering if you have any suggestions on what it might be?
@jacobadam4556
@jacobadam4556 Жыл бұрын
@@sandracruz8686 sounds like a bad headgasket
@jonreyna
@jonreyna 11 жыл бұрын
thuffheavenbound that's a vacuum line that controls the front windshield defroster, during the summer when you have the AC air coming from the front panel when you press the gas a little hard if that vacuum line is disconnected the air will stop coming from the front to the defroster side. just make sure you plug it back in.
@Tumusica311
@Tumusica311 5 жыл бұрын
whats the part # thuffheavenbound is showing you my ac will stop coming from the front panel if i hit the gas i need to check the part your saying to see if its connected,can you please send the # or pic to me. Thanks jonreyna.
@reeferjames1432
@reeferjames1432 5 жыл бұрын
Good job. Very hard to work outside as it is.
@jacobadam4556
@jacobadam4556 10 жыл бұрын
takes about 5 hours to do those intake manifold gaskets top to bottom, they all pretty much go bad at 100k in the windstars and freestars. you dont have to pull the upper cowl on the windstars only the freestars. just have to get the wind tunnels loose from the top clam shell and wiggler the top shell out. all fords 3.0, 3.8 and 4.2 have that issue with bad intake gaskets throwing rich and lean codes. ford slapped the cheapest trash in there they could find . and you must always use the sequence on the intake manifold, if somebody else pulls and installs their manifold without sequencing it, it can warp and ruin the manifold. the way you torqued that is a good way to warp it, just a heads up
@reeferjames1432
@reeferjames1432 5 жыл бұрын
Jake, mine got a engine code (misfire on cyl 1). P0301 the only thing that fixed it was a new intake manifold gasket. You are spot on. I also of course replaced all injectors at 200k. Thanks brotha.
@sandracruz8686
@sandracruz8686 Жыл бұрын
Reefer James , what do you mean? Can you explain that to me please I'd like to learn more about it I'll.
@talkntribe
@talkntribe 10 жыл бұрын
Great video. I am cursed by a 2000 windstar 3.8. we've been having no heat in the vents. Heard clicking so replaced the blend door actuator. Still no heat. Found out rear panel had no heat either. Checked the coolant tank and it was at the bottom. We have no codes, no lights indications, no overheating. Filled the tank back up. Drove with heat on high on the freeway. Only to find we had really low tank again. I checked and on the driver side of the engine there is a nice puddle of coolant right below the throttle body. Our setup is identical to yours in the videos. Looked at the firewall and it was sprayed with coolant. My wife revved up the van and I saw spitting. It looked like where the thermostat is. Not sure. We get little heat now, still no heat in rear auxillary. I'm thinking its that water pump water line you replaced. Atleast I pray it is. I don't have the money to do this gasket job. I'm watching your videos religiously. Hoping I can do this if it is that pipe. Hoping its a hose though :) Thank you for this video. Wish there were more. Would love to see how to change the coolant in these. Mechanic told us never do a flush because other problems will arise. Our container is nasty inside and we never did a flush. Had it since 06.
@bubbaboud
@bubbaboud 8 жыл бұрын
+talkntribe thats the water by pass tube gorun on top of bottom intake i had to change mine
@andyvasquez7890
@andyvasquez7890 3 жыл бұрын
Thank you for this right here life saver!
@jessedogg
@jessedogg 11 жыл бұрын
Thanks Jon these video sure gave me the courage to work on my windstar van
@Solely_Sasha
@Solely_Sasha 11 жыл бұрын
This video is great. Please make more videos to help people fix their own $hit
@heatherwilliams1537
@heatherwilliams1537 10 жыл бұрын
I have a 1538, 0171 and 0174 code coming up on my 1998 Windstar. I was thinking I need to replace the intake manifold. Now I am learning there is a right and a left and a lower. Now I have been contemplating changing the right, left and gaskets. Would you suggest changing only the gaskets? Upper? Lower? control sensors? How do I know which to change? I had four codes on. I already changed the air mass flow sensor, O2 sensor, plugs and wires, and sprayed the hoses with starter fluid and did not find any leaks.
@heatherraygoza1069
@heatherraygoza1069 10 жыл бұрын
this is heathers husband fixing heathers windstar
@thuffheavenbound
@thuffheavenbound 11 жыл бұрын
Thank you Jon for your reply. I have one more question, I have a picture of a part that I need to know what it is. I'm trying to figure out how to send it to you. Not good google.
@wryguy
@wryguy 5 ай бұрын
How the heck did you get the water pipe coming out of the right side of the intake back on? I cannot get it to clamp over the clicks. Pulling with all my bodyweight!
@Eeropolvasti
@Eeropolvasti 8 жыл бұрын
Well done, good job!! So, correct torque, also for this lower intake, is 89 inch-pounds?? And correct sequence, start from the middle, and then go out, changing sides?/ Why did you change this lower intake gasket?? Usually upper intake manifold gaskets go bad...??? Thanks, youtheman =) Ps. was that waterpipe also leaking, inside upper intake?? Very common problem.....
@heatherraygoza1069
@heatherraygoza1069 10 жыл бұрын
hi, just wondering how u clean the lower intake u dont show it on your video that part, i been doing very good with your videos thanks
@chrisford7775
@chrisford7775 4 жыл бұрын
What do I do about my bolts turning they wont come out of the intake its just sitting there turning
@thuffheavenbound
@thuffheavenbound 11 жыл бұрын
Jon what is the red line at 1:05? The mechanic that was replaced my intake manifold gasket has disappeared and my godson is trying to help put my van back together. Everything is done except for this line and one other part. Can you help me please?
@hvillalobos1317
@hvillalobos1317 4 жыл бұрын
Is a vaccum line coming from intake manifold, you need to remove the engine cover from inside of the van, I think has 3 clips.
@unknown4mat584
@unknown4mat584 4 жыл бұрын
I wish I seen more of the fuel rail part I know were the 4 bolts are just don't know how to remove I have new injectors I Wana put on and it didn't dawn on me I could have taken that part below the clamshell of it is real dirty plus I put on the gaskets for the shell I still have the valve gaskets and the two metal ones to do I just didn't know were they went, I'm learning by watching videos learning it's not that hard I normally take apart computers and fix them this is some new to but kinda fun
@sandracruz8686
@sandracruz8686 Жыл бұрын
How do you reboot the computer?
@unknown4mat584
@unknown4mat584 Жыл бұрын
@@sandracruz8686 reboot the computer?
@unknown4mat584
@unknown4mat584 Жыл бұрын
@@sandracruz8686 if you mean car computers, that's not the computer I'm talking about, I mentioned computers you get on the internet with...
@sandracruz8686
@sandracruz8686 Жыл бұрын
Oh LOL ok
@Cocothemechanic
@Cocothemechanic 10 жыл бұрын
would it be possible for coolant to leak out from the lower intake gasket
@Tumusica311
@Tumusica311 5 жыл бұрын
@jonreyna do you have any email to contact you?
@remi0527
@remi0527 6 жыл бұрын
If coolant gets in there on the bottom is that ok
@charleshendricks9188
@charleshendricks9188 9 жыл бұрын
Couldn't watch it, made me seasick
@luispina941
@luispina941 9 жыл бұрын
Cómo puedo pedir en la auto partes ese gasket..
@jonreyna
@jonreyna 9 жыл бұрын
Brother puedes ir a ebay, busca gasket set, Engine Intake Manifold Gasket Set O lower intake gasket set Ford windstar.
@FloridaMan7337
@FloridaMan7337 Жыл бұрын
Don't use these plastic gaskets only use fel pro permadry plus or mahle
@jbilliardo-andomartires3106
@jbilliardo-andomartires3106 8 жыл бұрын
Japanese masage
Ford Windstar P0171 P0174 Upper Intake Manifold Gasket Replacement
19:06
FordTechMakuloco
Рет қаралды 295 М.
Cool Parenting Gadget Against Mosquitos! 🦟👶 #gen
00:21
TheSoul Music Family
Рет қаралды 33 МЛН
How Strong is Tin Foil? 💪
00:25
Brianna
Рет қаралды 36 МЛН
UFC 308 : Уиттакер VS Чимаев
01:54
Setanta Sports UFC
Рет қаралды 849 М.
2001 Windstar Water by-pass tube leak Part-1
14:54
jonreyna
Рет қаралды 268 М.
Windstar MIRC Codes
12:04
realfixesrealfast
Рет қаралды 85 М.
2000-01-02 Ford Windstar intake de abajo, lower intake reemplazar
8:42
auto reparaciones generales
Рет қаралды 503
Ford Windstar replace Water Bypass Tube
13:18
TheTeddy214
Рет қаралды 6 М.
Ford Winstar 3.8l p0305 p0174 Runs Rough - My findings
3:48
2002 Windstar Window Motor Repair
11:07
FixinThatUp
Рет қаралды 106 М.
Vacuum Leak- Stalling ,idles roughly, check engine light on
13:23
TheTeddy214
Рет қаралды 3,9 М.
Corrigindo o Sincronismo "Ponto" do Motor Escort Zetec 1.8 16V
15:06
Ford Windstar oil pan replacement HOWTO
13:06
Will Fix It!
Рет қаралды 1 М.
F-150 4.2 V6 Engine Hydro-locked Rebuild  2
7:11
ALLMUSCLE
Рет қаралды 65 М.
Cool Parenting Gadget Against Mosquitos! 🦟👶 #gen
00:21
TheSoul Music Family
Рет қаралды 33 МЛН