Wireless P10 Dot Matrix LED Display Using ESP8266

[@Dwi.P4]

Is there a way to display the clock using RTC, sir?

[@techs5564]

everything starts ok but whenever tried sending text there is nothing on the display except some horizontal lines. Any idea?

[@osgaleo2229]

thank you very much friend i will do the compilation in a mcu node as soon as i have my panel in hand i was looking for a project with this matrix here and i found you have a great job thanks for sharing !!

[@tanmay5946]

How is it scrolling forever in Hello World? Scroll() is being executed once

[@ravethan5596]

Hi I have p10 led panel how to connect the esp8266 mini to what pin no connect to which pin to panel

[@jihadkhorfan]

how many p10 screen can we connect together before it start flickering

[@drashtishah3369]

Can you upload the code for notice board using p10 LED display using nodemcu???

[@sajidsalim9908]

Are you get thus

[@suhashinighanekar7663]

I don't see any actions on LED panel with scrolling program

[@DrTRonik]

Cool... ✔✔✔

[@ElectroPoint4u]

Thank you!

[@electronictechnology4776]

I had done all the things but my led panel is in fully on with all led

[@urfreind1549]

Bro how we make connections between p10 led display and normal nodemcu esp8266

[@sanzhar4710]

hello comrades how to connect HUB08? I have 64x16 and ABCD. Where in the sketch do you need to add additional C and D?

[@ElectroPoint4u]

Watch the video with RGB display

[@TechnoAutomation]

Can you provide driver board?? I will pay for it. Location gujarat India.

[@luizandrade6438]

Great Job! I'm trying to use a NodeMCU to control a P10 LED Panel. Can I conect the NodeMCU pins direct to the P10 panel? Or I need a Logic Level Converter 3V3 to 5V?

[@ElectroPoint4u]

I have connected my display directly to the Esp8266 pins and so far I don't have an issue with that setup. However, if you want you can use level shifters for conveniences..

[@luizandrade6438]

@@ElectroPoint4u Thank you!!!

[@video-zc4qv]

how do you upload the code to the esp8266 module?

[@ElectroPoint4u]

Using a USB to serial programmer. The UART pins along with GPIO0 and RESET are broken out on the PCB

[@tuyenleuc6570]

I have p10 led panel matrix 32x16. How to connect the esp8266 nodeMCU V3? /* Pin Defination nOE - GPIO5 A - GPIO16 B - GPIO2 CLK - GPIO14 SCLK - GPIO12 r/Data - GPIO13 */ SCLK - GPIO12 What is this?

[@ElectroPoint4u]

This are the default pin labels. Search online for P10 DMD pinout and ESP8266 NodeMCU pinout.

[@anibalvilelarj]

Congratulations ! It is very nice and usefulll. I would like to use a NodeMCU, because I am going to use 3 digital pins to receive remote control(RF 433MHz) with 3 buttons. Please, what is the kind(model) of ESP8266 used in this video ?

[@ElectroPoint4u]

Thanks, I have used ESP8266 12f module

[@anibalvilelarj]

@@ElectroPoint4u , does It have 3 free digital pins ?

[@ElectroPoint4u]

Yes, but then you have to use the TX & RX pin as GPIO0 and GPIO1

[@anibalvilelarj]

I have noticed some small differences between the reported Gerber Files and the PCB used in this video, specially the power connector. Are you aware on that ? Please, could you make public its schematic, too ? Thank You !

[@ElectroPoint4u]

Yes, Actually that is Rev.2 board. I thought it'd be useful to have barrel type connector in the PCB, instead of just only scrub terminals.

[@jamalani4249]

how if use nodemcu

[@ElectroPoint4u]

You will find the pin definition inside the code. Connect the NodeMCU according to that.

[@1i259]

Nice work bro , can you use other language in the message like arabic or hindi ?

[@ElectroPoint4u]

Yes, you will need the font header file for that perticular language and you can use adafruit gfx library to include it.

[@ayuratnas0875]

Ka boleh minta codingannya?

[@ayuratnas0875]

Kirim di [e-mail]

[@kmuchlis7842]

Kalo mau belajar buka channel bonny useful bahasa indonesia menurutku sudah lengkap tinggal kita ngembangin.

[@riteshsinha5900]

not very informative ....definitely not for noobs [me]

[@ElectroPoint4u]

No one becomes pro in one day. Neither am I!

[@riteshsinha5900]

@@ElectroPoint4u code compiling error can you help ...

[@HarpreetSingh-nl1li]

@@riteshsinha5900 share the error