Wonderful DIY 3 Wheel Motor Bike, Belt Drive System

[@bayujulianto1975]

Wong 87 jatim -indonesia hadir. Mantap kreatif banget.

[@bondiola09]

felicitaciones desde Argentina!!! un fuerte abrazo!!!

[@adimulamlakshiminarayana6744]

Good

[@tnmo4752]

หารายข่ำง่ายๆเพราะปกติแล้วมันจะตั้องทำฟรี 1 ล้อ เวลาเลี้ยวก็จะไม่ดึงกัน ผิดแล้วช่างเอ๋ยใช้ไม่ได้ครับวิธีนี้ ผิดตั้งแรกเห็นทำแล้ว ใช้ไม่ดีครับืำใหม่ต้องหมุนฟรีล้อถึงได้ อย่างนี้เลี้ยวก็ขว่ำง่ายครับ

[@Heroes99999]

Hi There New Subscriber KHMER DIY I'm Here For You

[@empoyvid4866]

Wow wonder bacykel w motor dikit done.👍👍👍👍

[@subrisaja7395]

Wowww.... Amazing

[@dennisbecraft1303]

Without being able to calculate the gear ratio precisely, I can tell at a glance it's like being stuck in 3rd or 4th of 4 gears. No acceleration off the line or hill climbing ability and hard on the clutch shoes slipping so much until it can fully engage. This would be acceptable on very flat land with few stop & gos on long distance rides. It could slowly get up to what would be a proper ratio for the top speed gear of a multispeed transmission and get good fuel economy at a cruise speed....BUT.... a single speed drive like this, to be more practical, needs a compromise ratio that givess better acceleration & hill climbing ability despite the loss of top speed, especially for the more common use locally, requiring frequent stops or operation at slow speeds in traffic etc. I would have to know more about what kind of driving he will be doing most of the time over what kind of terrain to suggest a good compromise but I can see he mostly needs a larger diameter sprocket on the axle to achieve the better useability he would have like if he had to choose only one gear of 4 or 5 gears available with a transmission. For offroad use or low speed use in town with low speed limits & lots of stops signs, & hills I would choose the equivalent of 2nd or third gear out of 4 or five. For frequent longer, higher speed trips on open flat smooth roads, he might want a higher ratio like 3rd gear of 4 or possibly 4th of 5. A 4 or 5 gear transmission would, in most circumstances, NOT be very useful, fun or practical if stuck in either of its first or last gears, right?.

[@purwadisetiawan5631]

Keren bang👍

[@sundaysuccess4501]

I love watching this because I want to be part of it.

[@nivlongtv440]

việt nam xuất sắc quá bạn ơi

[@sayurKampung]

wah bisa jadi inspirasi untuk membuatkan setir cultivator saya ini biar enak buat belok kalo dilahan basah

[@jerrysan7338]

Super nice it's good in rough road

[@thiencoflorentino5363]

người nước ngoài đúng uy tín

[@phearabean6339]

បងបើកង់៤ខ្លីជាងនឹងប្រើតេលេបញ្ជា ធ្វើឲ្យមួយអស់$?

[@شوشوجابر-ر7ص]

تحية لك 👍عمل ممتاز هنيئا لك 🙏👏🎊

[@esan709]

Mantap 👍

[@ElephantSoul]

good video 👍

[@mediabengkelnusantara]

sangat inspiratif👍

[@requestmusikchannel8591]

Kreatifitas yang sangat bagus👍

[@btbnewsdaily6736]

តើធ្វើលក់ឬទេប្អូន បើលក់អាចថ្លៃប៉ុន្មានដែរ ?

[@xuantruongmaynhomcnc]

the video is very good to watch, and great

[@Adamchannel1993]

Sangat mudah untuk di pahami tutorial nya👍👍

[@edsonmarcosgarciamelo3905]

Amei o PROJETO, eu gosto disto aí ﾆ

[@gegersopian3413]

Mantap. Apalagi. Kalau. Pake. Pemindahan. Gigi. Mundur. Lebih. Mantap. Kalau. Mau. Atret. Ke. Blkang. Ok. Trimakasih

[@nikolaykostenyuk1855]

👍👍👍😁 отличная идея ! Супер ! ❤

[@ayibrasidijakatingkir2681]

1

[@atowarsito5427]

@@ayibrasidijakatingkir2681

[@echootehnikwelding7141]

Sangat kreatif

[@cuocsongbinhyenYouTube.]

Sáng tạo rất hay tuyệt vời 👍

[@darmono1232]

👍 tapi sanyang pembuatan rangka posisinya terbalik jd kurang kuat mudah mlepes

[@นิติกรปามุทา]

ซ่อนตัว นับถือ ไอเดียสุดๆ

[@recinosrodriguez3085]

Hola amigo bonito proyecto té felisito y té pregunto las Cañuelas de 2 x1 cuánto miden dé largo y el ancho de estremo a estremo

[@ДмитрийЕременко-к2й]

Хорошая самоделка

[@virgiliobautista6078]

Nice it's good idea bro it's amazing👏 🙀 😯 good job

[@adrianotiveavcsampaioa1ano134]

Adoro invencao

[@sugianto2078]

Piring an cakram belakang GK senter bos

[@cengceng1369]

Bos piringan cakram nya ngegeol bos

[@tanamkasihchannel]

super kreatif

[@sugandairawan844]

Terimakasih atas teori nya kang luar biasa 👍

[@hilalali2653]

صـــلوا ؏ الحبيب םבםבﷺ

[@raymondortiz1113]

Well done job

[@x007xo55y]

Mad in cambodia 🇰🇭....good job bong.

[@witosarlaw]

Mantap bang

[@davidwillard6556]

Get rid of that belt and add a chain for God's sake. That thing pulled off like my daughter's barbie jeep lol

[@bonekchanel5112]

Klo roda belakang mutar semua, beloknya apa nggak susah boos🙏🙏🙏

[@nitroracer7715]

Dude you need to work that steel. Such rigid frame work. No style to flow with that awsome front assembly

[@mbahcarrier1629]

success always for ....."KHMER DIY"

[@pedroluko6226]

Muito bom , parabéns fazer coisas , dá prazer e desinvolve as capacidades que todos nós temos , só precisamos à comesar.

[@dannyreponte3451]

Love it

[@nuryahman5417]

Keren siiiih...tapi klo bering blakang yg di as tengsh rusak...kemungkinan akan sangat merepotkan...cara penggantiannya..harus bongkar LASannya

[@ariestrese7429]

almost good.. down side is. on how the diskbrake installed.. also then side wheels and gear..

[@kar88]

Kretif Dan simpel

[@restorationofdirty]

Best working project 🌟❤

[@Servis-f3h]

the best

Hay quá em ơi ❤️👍👍👍

[@matfrijas9506]

Napalag🤣🤣🤣

[@lokchandsahu9665]

Km lagt m bamm sir👍👍👌👌👌👌

[@piciuflorentin9939]

The ideea is nice, however a little uncomfortable duebto no suspension on rear wheel. Plus that will shorten the life of the bearings 😥

[@mariaaparecidaferreiradasi9847]

Legal gostei a sua nota 10 jvm

[@jorgeleninbenavidezbenavid1362]

que bien por ese muchacho si los que consumirán drogas se pusieran a inventar cosas la vida fuera distinta saludes muy bien 👍💯

[@tedccccc]

At 11:39 you see that the rear axle only has a single belt pulley. Camera cuts to an angle from behind at 11:41 and it has a double belt pulley on the rear axle...well at around 6:30 you see that he turned the spindle designed for bearings into a solid shaft wheel hub...well if he did that, how in the hell did he get the single belt pulley off and get the new double belt pulley on?

[@casaighir]

انت اسطورة ملاحظة في محلها

[@alhajicktv]

Nice

[@bedionlanutantv13]

Nice job.

[@tacsayayo9487]

bad idea you must installed mono shock at the rear chassis wheels to prevent constant bouncing.

[@datlam5327]

Chế xong con xe này thì chạy xăng nó uống hơn bò hít nước mật

[@JesusHidalgoP]

Buenas noches soy de Venezuela deseo saber las medidas del chasis largo y ancho saludos

[@arulpahmi1829]

L

[@iyuntcahkediri8237]

Yang jadi pertanyaan kalau ujung ujungnya di las kenapa harus pakai bearing?

[@azkaalmisbah01]

Good idea

[@IstantoSonGoKongChanel]

From Indonesia... 👍👍👍

[@udinkasum5024]

Amazing god job my frens

[@edivaldoleozirio8111]

Boa tarde amigão quanto é uma bicicleta dessa

[@odinthor5245]

I like

[@alexzsurzs2031]

Very nice

[@trisuranto9922]

tempat duduk jok motormu kurang tinggi broo...bisa jadi motor 3 roda..

[@jtatl3311]

I LOVE IT !!!!!!!!!! I would love to have one.

[@chanelbengkelbodyrepair4807]

Good my friend.. 👍

[@sevensihombingchannel6031]

Waow,Kreen 👍

[@FraysOfficial]

Nice project bro👏👍👍

[@vanluciohellsing711]

Bro, what is the size and thickness of that square bars yoi used? Thank you....😊😉👍

[@billbush-t5x]

Belt slippage, otherwise cool.

[@readthebible1958]

Good video

[@Mark_joe_dast]

Kenapa tidak mempunyai spring system.? Adakah kerangka projek ini boleh bertahan dengan berat penungang.

[@inspirasisenichannel]

Like...sucses

[@jamcarlo4781]

Excellent! Greetings!

[@皮皮島]

for a toothed belt, it was also necessary to take the gear from the camshaft head from the car engine

[@leanchannel9839]

nice friend

[@ดอนศรีตะปัญญะ]

ผมชอบรถสายพานครับ

[@casaighir]

عندما يسألك الشرطي عن اوراق هده الدرجة بماذا تجيب

[@jarbasbernadinosilva4471]

Quando precisar trocar os rolamentos tem que cortar a solda do eixo cem dizer que soldado fica desbalanceado

[@gegersopian3413]

Tambah. Di. Belakang. Nya. Pake. Keranjang. Kya. Gerobak. Buat. Belanja. Slamat. Chukcest

[@michaelszczys8316]

Looks like something I might have built when I was 12 with NO welding and only crescent wrenchs and maybe a drill.

[@chaospx]

Don't hate

[@scootersonlyrepair6773]

I bought something like this but also no welding. Just a few dozen mismatched bolt 🔩 and nuts. And no brakes.

[@rohitzanjurne183]

Whats bike race cable you are used to make thease

[@aliroh8211]

Masih produksi mas

[@Marcosvidanaroça]

Quero fazer um pra mim só com chance de mobilete

[@hgfghug7jffvjfugiguvfj667]

វាក្តៅហើយបើជិតម៉ាសុិននឹង

[@johannkostic9168]

Cool 😎 Mann

[@kaibannorkch2398]

ติดตามแล้ว นะ คับ

[@wakslamet]

kerren motor mesen nya boleh juga👍👍👍🙏 subscreb karro👍

[@agnaldoferreira3246]

Como chama esse sistema de embreagem ?

[@poutuyofficial3042]

ច្នៃអោយមានតំបូលដូចឡានទៅ

[@ppcooking7006]

มีศาลพระภูมิด้วย

[@projetoscaseirodoze]

Simplesment top.

[@marcosbraga1155]

Perfeito 👏