Woodworking Process of Making Wooden Surfboard by a Korean Woodworker.

[@mr.process]

📢 Product in Video : bit.ly/3l4TA6r 🚗 Location : bit.ly/3LjbI7c (Laau Product)

[@ReynoldsPerez]

H😅

[@TheThetechnician]

First wave nose dive……SNAP

[@donaldmatthies6026]

Watching this video, there is allot of steps taken to create something of usefulness and beauty. From programming the cut pattern on the CNC, joining and planning, sanding, to glueing all the joints. That was interesting process to see. Nice work. Thank you for taking time to film, edit and post this video. Liked and subscribed.

[@robertgrennan2824]

Great work, I bet the people giving bad comments have never done anything worth making a video of, my gosh , give the guy some credit, he did some great work , he didn't pass my the Mona Lisa

[@rcpmac]

How do you know this is “great work“ ? The design seems to lack finesse and misses several important details. The video also stops before completion of the project so even THAT is substandard. I’m a boat builder BTW.

[@lancemillward2462]

@@rcpmac agree. was painful to see the rough trim with the jigsaw all those splinters of wood everywhere. a big void that if it gets a leak anywhere will fill with water and sink. points for trying something different i suppose. An im a craftsperson, knifemaker and landscape designer.

[@robertgrennan2824]

@@rcpmac I'm talking about the action of it, I don't see you posting your videos online for idiots like you to judge. It was a great effort, maybe not a masterpiece

[@gwakjune]

목재 가공인데 목공풀을 안쓰고 록타이트 쓰는건 생소하네요. 샌딩 칠땐 귀마개랑 마스크는 쓰셔야 오래 일하실탠데..

[@marrlang7439]

목공풀은 물에 취약합니다. 물에 젖게 되면 접착제 자체가 분리 되어 버립니다

[@jimmyloe7780]

Nice job

[@jdk2320]

와 서핑보드 제작 공정이 꽤 복잡하고 어렵네요 ! 잘 보고 갑니다

[@michaelripley4528]

One guy - One board ❤ Great video!!!

[@봉봉-u2m]

그냥 나무판자인줄 알았는데 과정이 엄청나게 복잡하고 손이 많이 가네요... 잘보고 갑니다!

[@PA3GUQ]

The guy still has all 10 fingers? Amazing.

[@luciobezzi]

🤣🤣🤣🤣🤣🤣🤣

[@PA3GUQ]

​@@luciobezzi What is the funny part? Ps, board is great though.

[@damirlorca1298]

awesome!, i think you need also a air vent for the board to not explote when it gets hot

[@shaunmaree6493]

Finished board looked good, too many haters in the comments.

[@raflonoce]

당신의 작업은 믿을 수 없을 만큼 훌륭하고 잘 이루어졌습니다. 작업에 어떤 종류의 접착제를 사용하셨나요?

[@jhonnyfernandoencarnacionc5436]

Buen trabajo saludos desde Loja Ecuador.

[@constantinosschinas4503]

The very last steps with the stencil and epoxy putty were a bit weird.

[@paulgerrard9227]

Yes. Korea. The world surfing masters.

[@sc0or]

They have to pull a router, not to push it. Because of a rotation direction. This makes a more clear cut.

[@DeclanRyanRising]

The comments here are portentous. I noticed a few issues, like the lack of a mask and some messy technique but how could a surfboard get any more expensive? May as well make it outta California Redwood. It's still a beautiful thing despite the fact that the carpenter is only a few years in.

[@Smokkedandslammed]

I wanna see how good his boards are in 5 years! Good job dude!

[@mikethespike7579]

I don't know if a surfboard made of wood in such a complex design like this has an advantage, but I do know that since the mid 1960s most surfboards are made of light glass fiber with a poly-foam core. The more expensive ones are even made of carbon fiber.

[@seangerst6561]

Depends! Of course the wood ones are heavyer but they feel soo much more ,,alive,, They haven't got that much flex and they are probably also not really for like the heavyer or bigger waves. But the wood longboards, are just beautiful and I would love to have one of the wood ones in my quiver as well!!! And last but not least, they really start to get more and more into using natural materials again, something like algave strong or so, its a realy interesting topic, and i love to explore new stuff on the market.

[@이기리스-y3v]

ㅋㅋ그냥 장식용 나무보드인거같네요

[@VAdu56]

mets de la musique dans ton Atelier, ce sera plus Cool, pour réaliser ce travail... superbe; Bravo, c'est magnifique...!! pourquoi ne pas intégrer directement de la mousse expansée, ou vernir l'intérieur pour protéger le bois..? pour une meilleure vie avec le temps...!

[@reallyyouthful]

I'm not surprised he has a band-aid on his finger.

[@ElephantSoul]

Amazing work

[@307signal]

장비도 그렇고 엄청 부럽네요

[@Bepnm]

According to the taped Finger, he is not always so precise with the hammer.

[@annabraun3509]

Did anyone notice the band-aid on the finger

[@davidpowell6098]

I'm surprised he has all of his fingers, and other limbs intact, and the way he abuses his tools is another worry, too.

[@bangla35love]

거의 배 한 척 만드는 분위기네요. ㅎㄷㄷ

[@remerglobal]

Bless you!

[@jzabala3871]

it has air inside?

[@PROProcesss]

Great video For some reason I always thought surfboards were made of plastic, I was surprised to see them made of wood. I still don't understand why it's a corked and hollow inside, can anyone tell me?

[@eg8343]

For voyance, to be able to float. If it has no spce inside, it is more denser than the water that make it sink under the water. Similar to concept of ships or simple example a sealed empty galon that floats into pool. Related to pressure.

[@PROProcesss]

@@eg8343 Oh, I get it. I've just seen it made out of foam and treated with resin.

[@juststuff5216]

Less weight, for manoeuvrability! We all know a log can float in water, but surfing on one is another story. If a wooden or foam surfboard gets waterlogged, it's really hard to handle ... believe me, I've experienced a (damaged) water logged longboard, and it was near impossible to manage, and even worse when it came to duck diving! So less weight the better, that's why most boards are made of a light, dense foam. Wooden boards are more for show. Example, how many wooden boards are used here? kzbin.info/www/bejne/hJS3YqOAZ7qlq9k Or here? kzbin.info/www/bejne/hIXKcqR-brJ4m8k The answer is; None!

[@PROProcesss]

@@juststuff5216 In fact, a lot of plywood is produced here, and plywood is lighter than solid wood. But I still don't think it's feasible and it's easier to make it out of plastic.

[@jamesforbes2871]

The original boards were made from solid balsa wood, then "shaped" to suit. The builders were called "shapers" for that reason. When balsa became outrageously expensive they turned to poly-urethane foam block. The rough shape is then covered in fiberglass reinforced polyester or epoxy. The board in the video is called a "space-frame" construction, like an airplane wing. It will be many times stronger than a foam and resin board, though clearly it requires much more time and effort than a polyfoam board.

[@stevehamilton9418]

Good attention to detail but would like to see both sides of the final product.

[@gaspartellez6620]

Hello Chingu ,,, are you using pawlonia wood ? thanks

[@240619721000]

покраска из баллончика с масками ИЗ ФАНЕРЫ- это АДИЩЩЕ!!!! Челу похоже самому стремно показывать этот мрак, он даже не повернул ее после заливки стороной с "графикой"... Про вес девайса страшно спрашивать. Мож это просто в кабаке каком-то повесить, а не по прямому назначению? )))

[@666Hansen]

Its more like glueworker than woodworker ;-)

[@havingf]

I am surprised he has all his fingers

[@ДанКо-д5ю]

👍👍👍🤔😎

[@acctekchinadeedy]

good job, cnc router manufactuer here

[@kc2sc]

Shop 101...safety glasses

[@노송균-i9e]

아니 서핑보드 목공이였던것도 몰랐는데 이렇게나 정교하게 만들어지는 거였다고? 그냥 플라스틱 판때기인줄암 ;;

[@aweezywun]

When is it going to be finished????

[@razvanbutiac7684]

Hei mate! Nice work! But for your health... you must use some dust masks man... the wood dust it can irreversible damage your lungs.

[@307signal]

물속에 담궈논 본드는 아교인가요????

[@spindvergifter]

Looks more like a bad do-it-yourselfer than a professional. No reasonable dust extraction, dusts the whole house full and then has to sneeze. And a lot of glue is known to help a lot.

[@subramaniamchandrasekar1397]

What is that glue he is using? Looks very fluid. Regards.

[@warchitect73]

gorilla glue is the brown clear stuff that gets foamy. he didn't use water to help activate it tho, as its a hydrating glue... the early stuff was CA glue, and then fiberglass resin was used at the end for the coating. also a crappy job... lame stencils, lame graphics...

[@nwie9mm261]

@@warchitect73 ...at the first it was Loctite 401...

[@davidattenberg4720]

Worst glues used for anything near water.

[@enricogiusti8213]

👍👍👍👍👍👍👍👍

[@carlosnatal3938]

eomcheongnan!

[@tyronegoncalves3014]

Is Ned Clap it. Going surfing at the end?

[@인생찐맛]

제길 무슨 서핑보드 모형품? 파도를 가르는 성능은?

[@DIY-vj1uo]

서핑보드 비싸유 ? 비싸면 저거 따라 만들고 싸면 그냥 가서 사고... ㄷㄷㄷ 암튼 대단합니다 감사한 영상입니다

[@ads1374]

작업자분 조선족 인것 같네요 일하는 모습 패션 관상 두루두루보아 조선족청년!!!

[@tinkeringwithmark1186]

You should sell this as a kit!

[@robvangelderen2359]

Yes that is also my question

[@rawbacon]

So he fiberglassed only half of it?

[@jasonturner1045]

he didn't finish it. what about the bottom and the fins?

[@katsukiowabara3725]

He forgot the fins.

[@seamuscashin2606]

i would like to see the inside varnished and for gods sake were gloves with polyurthane glue it will destroy your hands good wood work like a plane wing

[@leeontheboards]

👍👍👍

[@307signal]

너무 가볍지 않나요??? 어느정도 무게가 있어야 안정적일텐데요

[@dionlee1728]

13:22 내가 목공배울 때 직쏘 저렇게 잡으면 진짜….. 손가락….

[@nurungji-]

위험한 장비에다가... 손가락이던 손목이던 잘려서 날라가면 그담부터 안하겠죠 못하는건가

[@sentinelle5076]

Du bon matériel mais un travail dans l'ensemble plutôt moyen avec un manque de finesse dans sa réalisation.

[@VAdu56]

et j'aurais mis de la mousse expansée à l'intérieur, ou au moins vernis...!!

[@sorokin_sv]

Будь здоров 😏

[@LordDustinDeWynd]

👋 👍 🙃 🥰 !

[@jean67ify]

Mettez des protections respiratoire, vous pourrez surfer pendant plus longtemps !!!

[@Полиграфист-п4з]

Всё ясно. Доска для сёрфа делается из клея и палок )))

[@Loveteeth]

이제 3d프린트 관련 제품들이 많이 나올듯

[@markfromwestcoastwoodcraft7633]

The timber frame surfboard, this thing will weigh a ton

[@AllRock90]

Кровь из глаз от такой "культуры производства".

[@kevinlucas8437]

Didn't seem to be finished, just black paint ??

[@hss9962]

전문?

[@annabraun3509]

No respirator????

[@joseeduvigisdiaz2759]

Where fins?

[@patrickhayes3099]

Fin box?

[@jonnekjonneksson]

The attention to detail and overall precision are totally absent. Nice idea, full tool spectrum, but overall a sad construction.

[@jamesforbes2871]

You're a laughable clown. There was neither a lack of precision nor detail.

[@깨깨]

🏄‍♀

[@JorgeGalvao-vz8so]

Cadê as quilhas?

[@erichaskell]

Weight?

[@eduardbalalykin5339]

Титановую арматуру, внутрь вклеивать надо, чтобы акула зубы ломала.

[@battlebotts]

Gorilla glue? Really. What a shame

[@brettbulseco8977]

smart name. laau in samoan is tree. thought it was supposed to be hawaiian at first, but that would be la`au, and it would mean medicine.

[@psand7402]

공구다루는거 보면 전문가는 아니구마

[@scott3708]

Apprentice.

[@chiranagheorghitaeugeniuth98]

sloppy tehnique, a mix of materials, inconsistency in quality..... not very impressive

[@mikhailkopov229]

А цена? Столько ручного труда и затраченного времени. Доски сейчас не так производят- пена, а вокруг оболчка из волокна в смоле. В 20 раз быстрее, в 3 раза легче доска и в 10 раз дешевле. Это штучный продукт, на заказ.

[@smmsex]

Это шлак какой-то... Это я тебе как столяр говорю. Это очень небрежная, и некачественная работа!

[@mikhailkopov229]

@@smmsex Так она еще и тяжеленная.

[@mmmijuo5407]

저바이스고정하기전에 하늘색 스폰지같은건뭘깡

[@haivenw]

咁就做完架拿？

[@DD-DD-DD]

Really sloppy technique. This person will lose fingers at some point.

[@kinghoodor8475]

I run this workshop.. at this time I got full schedule, so my student on video so.. be generous😢

[@DD-DD-DD]

@@kinghoodor8475 Removing guards (such as on jointer) is dangerous. His technique passing the wood through the bandsaw and using the jigsaw was terrible. You aren't doing him any favors. Train properly and provide safe environment or close up shop. I know carpenters with only 2-3 fingers on a hand.

[@kinghoodor8475]

​@D D jointer is old Japanese one so there wasn't safety guard when I bought it. and during 7years there were no accident In my work shop.. and the guy in the video he only took the wooden surfboard class(only10days).. not the full time class.. anyway thanks for your advise

[@michaelripley4528]

@@kinghoodor8475 I like this process and the Way keeping it simple - One dude - one board 👏🏻👏🏻👏🏻

[@Comeriokid]

Awesome video my friend. As a carpenter of 30 yrs, the worker has great technique. Ignore the keyboard warriors 😂

[@whirledpeas1182]

This woodshop got a wierd vibe to it. Maybe it's a rental space or something? Very odd techniques as well. This dude clearly not an experienced woodworker....

[@olafpas2053]

Лажа это, а не доска.

[@incy55]

A good video but a bit of an embarrassment to wood workers around the globe.

[@jorgemontefusco650]

Huh? What’s your point?

[@incy55]

@@jorgemontefusco650 If you were a wood worker you would understand

[@brianlee360]

Gorilla glue...worst glue ever.

[@song-pd5ry]

공구다루시는게 전문가는아닌듯 어설퍼보이네여

[@boedidley823]

Great work! You have to be a gorilla to squeeze the bottle.

[@TheDarthvader123]

Nope…!

[@isakeles588]

Very amateur!

[@kgyang3704]

CNC 툴 방향을 오른쪽으로 사용하시네요.. 깨끗한 가공물을 얻으려면 반대 방향 즉 왼쪽으로 가공하셔야 하는데 일부로 거칠게 가공하시는지는 모르겠으나 제가 판단하기로는 CNC 목재 가공 방법을 잘 모르시는 것 같아 보여요.^^ 그냥 지나가다가 그게 보이네요.. 가공물이 거칠어서...

[@이광운-c8j]

날물 방향대로 제대로 돌아 가는데요? 영점을 이상한데서 잡는게 희한하긴 하지만요 목재 종류가 그런거에요 옆면을 보시면 깨끗하게 나오지만 윗부분이 무언가가 잔뜩 낀거야 원래 그런목재니까요

[@kgyang3704]

@@이광운-c8j영상에서는 상세히는 알 수 없으나 안쪽 작업은 날물이 도는 시계방향이 맞구요. 바깥쪽 마무리 컷팅 작업은 시계 반대 방향으로 돌아가야 되지 않나요? 눈으로 보기에는 가공물에 붙어있는 보풀이 제법 심하네요... 제가 착각 하는 건지도 모르겠지만요..^^

[@둥글게둥글게-o9b]

@@이광운-c8j x축 y축은 잡혀있어서 소재두께에 따라 z축 영점만 잡는거라서 그런듯 싶습니다

[@DIY-vj1uo]

이야 전문가들 많네요 좀만 더 붙으면 저 서핑이 산으로 가겄다

[@moroshobby2378]

정방향 역날 쓰는것 같네요 칩이 누르면서 클램핑 역활을 하는것 같구요(삼나무같은듯) 내부 프레임은 자작나무 합판4t인지 6t인지 머 그건 버가 많이 일어나는데 날물이 새 날이 아니거나 내부에 들어가는 구조역활이라 굳이 샌딩까지 완벽하게 안해도 되는 것 같아요 공정시간을 아끼려는 심산으로 보입니다. 4mm 엔드밀 역날이거나 2날 정.역 콤비날인것 같기도 하고 고릴라본드를 쓰긴하는데 이게 목공도 되고 나쁘지 않습니다. 해외 제작사례보다 먼가 거친느낌은 있지만 국내에도 이렇게 제작하는곳이 있다는것만으로도 최고에요 작업공정 1. 발사나무이거나 삼나무 가공(프레임 외측) 대패로 두께 가공 2. 자작나무합판 프레임 가공 3. 프레임 조립 접합 및 샌딩 4. 하판 본딩 5. 상판 본딩 6. 핀자리 홀내주고 어뎁터?같은거 넣고 믹스엔픽스같은걸로 마무리 (에폭시) 7. 락커로 하판에 로고 페인팅?(락카 스프레이 페인트-일신락카로 보임) 8.마스킹후 유리섬유 적층 에폭시 작업 9. 샌딩(후 페인팅을 할경우도 있고 나무 본연의 느낌을 그대로 두기도 하는듯) 10. 라미네이팅(에폭시) 11. 미끄럼방지제 도포(추측) 대략 이정도 공정으로 보여지네요

[@ЮрийКонрад-н7з]

Актёр безрукий

[@poznovatel1]

🤏🤏🤏🤏👍👍👍👍👍

[@outsight-]

이건 마스터 프로세스가 아닌데?? 수습생 수준의 만듬세 머임...

[@windynotes]

The whole process is so inefficient. And wasteful of time and volume used with the glue application.

[@jaymondavis6509]

How would you do it?

[@windynotes]

​​​​@@jaymondavis6509 please take a look at comments and replies by Mikhail & EVE Wartune. And other Koreans too.

[@気ままな風来坊]

全然欲しいと思えない、、、 技術が低い