Finally love to see you back. Can't wait to see you in Florida.... let's get him to 100k.....
@AmfP_892 жыл бұрын
Dude your fab work is getting so good. Can't wait to see Kyle's cage
@mi16pim2 жыл бұрын
Cant wait to for them to cut out the MR2's roof-hoop😎
@waymenlawrence20642 жыл бұрын
Dude his fab work is already good!
@built_by_jones62622 жыл бұрын
3 years of watching this rx7 and still I can't wait to see it back up and running again. Love the work you do.
@brocklowe1182 жыл бұрын
Dude this has been the longest car building ever. I hope like hell I can see that beast run!
@eugenevalentine9252 жыл бұрын
man at this point he just needs to sale that mfer and start a new simple build. car gonna be nice and have to much money into, would be scared to race it 😂😂😂😂😂😂
@taylorh1552 жыл бұрын
@mashi DO she told me about it when it was still a rotary.
@jonnoMoto2 жыл бұрын
Ha. You've not come across project binky. 8yrs or 36 episodes so far.
@sjv65982 жыл бұрын
@@jonnoMoto I was about to comment the same thing 🙂
@seankelly42052 жыл бұрын
Rx7 Mr2 face off again 4 years later ,I would love to see it cause this Rx7 is absolutely no joke now serious work put into both builds the fab work on this Rx7 is pure art respect hayden
@jaynikk7582 жыл бұрын
Lol not sure if he can make 13XX+ HP on a stock block but either way if Kyle misses 3rd he has a decent chance 😂
@herbiederby33942 жыл бұрын
Wyatt's a trip...😆....great work as always man on all 💯 and a safe trip...like the fittings....💪👍🤙🙏
@joeygude.12022 жыл бұрын
That is sounding awesome!! Whoo hoo get Er done !
@5187josue2 жыл бұрын
Glad to see that you are doing well. Have a safe trip
@tjabbie2 жыл бұрын
Good to see you back Hayden!
@davidblanck41312 жыл бұрын
So glad to see progress happening. I'm probably almost as anxious as you to see what the RX-7 can do.
@joshs1992 жыл бұрын
Sheeew buddy... Can't wait to see you ripping that thing on the track..! Watching the progress you've made over the years is awesome. Your a talented hard working dude. And your build is Sweet..
@Phil-rs5wl2 жыл бұрын
Running the catch tank in the back just make sure the line stays @ a downhill angle. I've seen them have low spots fill up and basically created a blockage in the line. Just make sure it doesn't sag below where it will go into the tank.
@ismaelmarrero83772 жыл бұрын
The 8 Rotor is looking amazing can't wait to see it running have a good time in Florida.
@alexelrod2422 жыл бұрын
Wyatt sounds like he's a riot Semi intentional rhyme
@Bigninjon2 жыл бұрын
The wait will be worth it if the vids keep coming!
@drew538322 жыл бұрын
Keep taking care of yourself! Best of luck man!
@thomaslewis78832 жыл бұрын
Look forward to seeing you and the car in Florida. I'm expecting some low 5 second 1/8 mile runs, Have a great time in Florida.
@97vr6gti2 жыл бұрын
Cant wait to see you back behind the wheel excited for you
@carlosyo20112 жыл бұрын
Always nice to see your work man you really take pride in what you do 👍
@jcnpresser2 жыл бұрын
Your alive! Awesome dude!
@87speedshop272 жыл бұрын
Beautiful work. Going to be a very nice finish product with all the lines AN 👊
@danielhigley85432 жыл бұрын
I clicked on this so fast..... I was beginning think you had quit on us. I'm excited to see you make a few passes on the car.... make sure Jack Stand is around..... he is a smart dude when it comes to set up.
@JT-th5lp2 жыл бұрын
Glad to see you back, fl will do you good to finish the rx7. After This vs That will be great to see you do the cage in the mr2.
@davidkane86602 жыл бұрын
All the hard work has payed off hayden. Looks great. Have fun with the boiz
@bnmperformancefab2 жыл бұрын
Man I relate to the struggle way to much, the bouncing around in the video makes me think of what my videos would look like haha
@shortybynature692 жыл бұрын
Florida needs you!!!
@brettgump2 жыл бұрын
Good to see you again bro 👍❤✌
@racerx20842 жыл бұрын
Everything looks top notch. Keep up the good work
@kensmart54002 жыл бұрын
Love that you are going to hang out with the boys
@davidr19972 жыл бұрын
Beautiful car Hayden!! Keep up your great fab work!! 💪🏼🚀
@TheJoebobmel2 жыл бұрын
Make it happen Captain. Will be watching.
@gixxernut80212 жыл бұрын
Looks really good buddy!! Good luck!
@cbdreamer17092 жыл бұрын
Great to see you bud! No worries
@robertroop38612 жыл бұрын
Glad you're back
@Nerdless422 жыл бұрын
Wow so good to see you made new video can't wait for the next one
@gavinoliver80742 жыл бұрын
You're looking so well. No need to apologise. Work is needed, work hard play hard my dude.
@Ricky-nq7lu2 жыл бұрын
Good to see you back bro.
@lastmanstanding51172 жыл бұрын
Grind hard brother!
@Rome3aaro2 жыл бұрын
That fox body build is wild.. very nice
@ryansantiago9412 жыл бұрын
Today - “IN YO FACE WYATT” At the track - “GUYS DON’T TELL WYATT”
@hcfcustoms2 жыл бұрын
Engine bay looks really nice👌 Love this beast💪
@thompson_fishing_adventure38652 жыл бұрын
That is clean as hell
@ccrDan2 жыл бұрын
That engine bay dude 😍😍😍 your work is beautiful 👊🏻
@RaceBrosCarlos2 жыл бұрын
God damn finally! Atleast I knew you weren’t dead 😅
@davidring24382 жыл бұрын
Wonder if it's been set long enough to warrant cleaning the injectors 🤔❓
@tonyross73762 жыл бұрын
Sick work Haden
@tylerjones47682 жыл бұрын
Hell yeah bud let's go!!!
@brocklowe1182 жыл бұрын
I don’t think I am going to live long enough to see the rx7 rip
@okobojian18602 жыл бұрын
😂😂😂
@tracyscott702 жыл бұрын
Fab work is outstanding 👏 👌 🙌
@Pipitarutor2 жыл бұрын
Yo Hayden! The filler cap with the pressure relive should be last in the system, closest to the thermostat. If you think about it, it makes sense, the pressure is going to be lower the cooler the coolant is and if the cap is on the hotter side, it's going to relieve pressure you need to keep it from boiling. Hope it make sense, I kinda gave myself an aneurysm reading it back.
@ILiketurtles682 жыл бұрын
We gonna see you race the MR2 while in Florida?
@Todd9362 жыл бұрын
Man love the info and glad to hear u doing so good and u sound so happy in u r voice so that makes this video so much better we all love to hear good news man… I wanted to know how u feel about u r welder my son wants to weld and is taking classes I would like to purchase a welder for him and I want to only buy one to most of our fabrication
@lonnyself39202 жыл бұрын
love the purple AN fittings my grandson fav color
@stayathome3162 жыл бұрын
So in love with that rx7
@thomaslewis78832 жыл бұрын
To help with coolant flow during cooldowns and to help eliminate air pockets, drill some holes in that new thermostat. Why Drill Holes in Your Thermostat? I guess the obvious reason is to keep your car cooler, therefore, controlling KR. However, the holes only reduce overall engine temps by about 5 degrees so we have a much more important reason for this. While at the track you open the hood, maybe ice the charger and let the motor cool down between runs. This may bring your coolant temps down to very low levels, which is good however these cool temps may actually slow you down. With the coolant and engine cooled down there is no coolant circulating until the engine temps reach the temp of the Thermostat. This would normally be OK however when you're racing the combustion chambers heat up very quickly. So the coolant around the cylinders and heads might reach 250 degrees before the stat even begins to open. This is very bad and can cause high levels of KR in the back half of the ¼ mile. By drilling the holes in the thermostat you can eliminate this problem because you will always have a small amount of coolant flowing. "Performance blasting down the ¼ mile isn’t the only advantage of having holes drilled in your thermostat. If you live in a colder climate this $11 investment might just save your cylinder heads from being cracked and damaged from the sudden dive in coolant temperature as your winter chilled radiator dumps it’s freezing coolant through your heads. A drilled stat would be much more forgiving by providing a continuous flow of coolant and reducing sudden and drastic temperature changes." - Andy H Duluth, MN 1999 Grand Prix GTP 02/16/2004
@ILiketurtles682 жыл бұрын
Wyatt living rent free in yo head.
@BassManBobBassCovers2 жыл бұрын
Working as hard as I'm going to be when I see the RX-7 make a pass! 🤸♂️
@timtaylor61472 жыл бұрын
Love the LS stuff
@belcebu59072 жыл бұрын
HAPPY SATURDAY BLONDIE
@taylorh1552 жыл бұрын
Been waiting years for that rx7 vs mr2 race....
@raimondnu32 жыл бұрын
IDK that mr2 is Roddy AF Now. At this point Stupid Fast!
@taylorh1552 жыл бұрын
@@raimondnu3 pistons and rods and he is there.
@stringybarkin2 жыл бұрын
Noice work man
@cameronwallace122 жыл бұрын
A set of Johnson lifters I would recommend. Have some in a set of 2116 in my daily beater 👌🏼🤙🏼🤙🏼🤙🏼. Could also just be a faulty injector
@juntech80222 жыл бұрын
Month and a half hell yeah 👍🏼
@mikeshepard63932 жыл бұрын
Crx coming soon ???? Can't wait to see what u put in it man.
@addicted2fuel2452 жыл бұрын
Make sure you put some water wetter in the radiator. Using that you will see temps 15-20 cooler
@hondaland_2 жыл бұрын
Just a question but why not have one color for fuel and one for vacuum / PSI and one for oil and so on but that's just me. I have a purple car with purple hoses and purple fittings as well so I can't judge
@numlockkilla2 жыл бұрын
My iowa boy right here. Ask about the K boat. Tom we love you too.
@JESUSD67652 жыл бұрын
Them mustangs 🔥
@mcwillies27372 жыл бұрын
That tick you're hearing may be your injectors. Also, make sure your alternator can handle the amp draw from all the electronics you've installed. Noticed it was 13.4 volts and jumping around a bit.
@hyper85452 жыл бұрын
Gz man been waiting some updates and idk bout that tick but you should hear how noisy my gti engine is. I still think something is wrong with it but I guess that's just how they sound 🤷
@CWP19982 жыл бұрын
MISS THESE TYPA VIDEOS DAWG!
@Groovy_ls12 жыл бұрын
Have you checked to make sure the pushrod length is correct? That might quiet it down a little bit
@gnarkiller2 жыл бұрын
Hell yeah
@nessie427862 жыл бұрын
Yeah right! You been living that BMW life with your beard 🧔 and blond hair.
@blasterman172 жыл бұрын
Damn son, Wyatt moves out of town and you drop 50lbs 😂😂 #NoMoreDadBodSquad
@Korruptionen2 жыл бұрын
Hayden! Looks like you've lost weight. Nice work dude!
@rj_boostedz28972 жыл бұрын
Did you put ls7 lifters in it. Or are they stock lifters.? I’m just wondering. But either way sometimes these motors have lifted noise. Run it you’ll be fine
@madmod2 жыл бұрын
I missed you dawg
@madmod2 жыл бұрын
I need seats for my sn95!
@UNIB69N2 жыл бұрын
"working hard at hardly working" is my lil saying & so when someone is working I say "hey get to work", and when they not working I say "take a brake" it's a bit backwards but not lol
@tony212272 жыл бұрын
I'd like to see him put his touch on Leroys Turbo setup!
@Latezen2 жыл бұрын
That blowoffvalve spring is too weak. Pretty sure it should be closed at idle. But looks killer👌🔥
@matthenry93852 жыл бұрын
Tick tick tick tick, said every LS ever
@wiz_lsv26002 жыл бұрын
We missed ya. Wish I bought ur manifold instead Sheepey... waited 6months man. Tjanls for updating
@jayburrough43082 жыл бұрын
It was kind of hard to tell but didn't know if it was a lifter tick or an exhaust leak sounds like an exhaust leak to me but I'm not in person to hear it like you are Plus I'm on my phone good video good to see all the progress
@codypatrick55592 жыл бұрын
Can we see the RX-7 hurting feeling now !!
@josteincarlsen29052 жыл бұрын
You should do some badass manifolds for Leroy!!!
@okobojian18602 жыл бұрын
Good to talk kid, make sure you follow the idea you have. Life is like that 1320’ fast as hell and your running the 660’. Keep it at a 1000, it’s build solid, and give Kyle hell. Relax in Tennessee, , then you work your ass off. And you guys have fun in Florida, maybe Wyatt will get that truck rolling? 🤷♂️
@jackshepherd7022 жыл бұрын
Let's go!
@everythingbox2 жыл бұрын
Best 8 rotor on yootubes
@arcwhale55602 жыл бұрын
Hey just a reminder that if your making the catch can so far away you might get a lot condensation and you might have to add a bleed valve like cleetus did on the El Camino
@Metigulous2 жыл бұрын
Can you link me to this video please!
@n01z32 жыл бұрын
only way we know you alive is the boostedboiz vid. but as long as you busy man
@B5S4SCHA2 жыл бұрын
I’m putting a 6.0 into my SA at the moment, probs gonna make my own mounts, but you should totally remake the engine mounts maybe trans mounts too, Grannys doesn’t make shit anymore for our cars.
@derekschulze91682 жыл бұрын
Fl2k here we come🤘🏽🤘🏽🤘🏽😎
@sethwright2 жыл бұрын
Don’t worry about the lifter noise. My notch does the same thing.
@187maker2 жыл бұрын
Since your doing everything so clean please swap out rods and pistons so you can turn it way up
@shortybynature692 жыл бұрын
Please move to Florida!!!!!
@AllanBadawiPhonesAndCars2 жыл бұрын
Just move there and start a crew with the boiz and get that $$$$
@adriansierra7512 жыл бұрын
Yes.
@makeitorleaveit12 жыл бұрын
Dude show us all that you do it would be great content