VW TRANSMISSION SHIFTS HARD VALVE BODY REPLACEMENT FIX

[@WorldMechanics]

Products that we use and recommend: ► Panel Removal Set: amzn.to/3YiMADu ► Assorted Fuses: amzn.to/4fx4s3F ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Mobil 1 Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torx Set: amzn.to/3xlCkfT ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► Voltmeter: amzn.to/4hB6Zvk ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics

[@808kingkoopa]

In most of these cases I’m see, it’s just your tcm and ecm that sends your can in limp mode, under the carpet on the passenger side is your ecm, and driver side is your tcm. Due to poor weather stripping, moisture and condensation builds straight puddles underneath your floor board, go to the junkyard and pull them with matching numbers. It worked for my old Passat 3.0.

[@jlh505050]

Thank you. Very clear instructions. You saved me a lot of money.

[@Pistonstrokes]

Thank you I just bought a car with this problem and if it's this easy to fix I will have saved a lot of money

[@kirksunley1381]

Did you have to preform any kind of adaptation for the transmission to reset back to factory defaults and allow the computer to relearn?

[@muffemod]

He doesn't know.

[@kirksunley1381]

@@muffemod and it does require a software reset...something along the lines of VCDS scan and reset within the module! I have done a couple of these now and at about 100-125k miles the solenoids are pretty much shot, the valve body itself is generally still serviceable. The solenoids are creating the issue(s) of hard shifts, and slips between gears. AND always use manufacturer fluids in servicing.

[@angeltapia682]

hello from San Juan , Puerto Rico USA. This video is great! you helped me save $900 !!!!! you guys Rule!! thanks

[@lreyescordova]

Hi! I have the same problem with my vw passat 2T 2007, I live en Caguas, where did you fix yours?

[@johnnydeutschemark3620]

This was a (sort of) "recall" by VW on 2004-9(?) Passat's, Golf's & Jetta's & Beetles in the usa with a rather stringent and spotty acceptance at the dealerships..some did / some did not offer the repair people were pissed! ...Looking forward to watching your video..

[@thehobbyshoptx]

Great video! What are the torque specs on the bolts and the tightening sequence?

[@khaoss7824]

Would be great to get those spec if possible thx going to start any time now

[@nadirkhan7552]

2:11 Good tip to tight the bolt now cuz later maybe you forget and drive . 9:12 Good suggestion to check your suspension 👌 Subscribed 👍 🎉

[@juanvega3548]

Where did you buy your Valved body from? What website?

[@Master_jjayy]

Every video DIY I search up on KZbin and I hear my brother with that cool accent talking I immediately smiled and yes this fixed my 05 vw golf 1.8 Replace the filter replace the fluids with genuine fluid from Volkswagen get it on FCP euro

[@IDontKnowLuis]

You got insta? Or snap I wanna see your vw

[@sabrinafelix2511]

I have an 05 jetta 2.0 it was leaking oil from the coolant box I got new seals for the bolts that go to the coolant box, changed the filter and fluid also changed throttle body a year and some change ago. . If that didn't fix it I'm gonna try this

[@Rx330lexuslover]

🚩🚩HELP! I have a 2007 volkswagen jetta. My transmission only hits from 1st to 2nd! No check engine light. What is it?

[@luisgomez7019]

after install valve body you need to reset it. How can I make the reset procedure?

[@ivanvega2821]

Would a bad/faulty valve body cause the vehicle to not move in any gear? I recently got a transmission DTC of P079500, it has me going crazy because I’m trying to figure out if the transmission needs to be removed to replace torque converter or potentially whole transmission.

[@_Volkhunter_]

“Make sure not to drop tgis in the ground” 1min later sets it on the ground 😅. Plz dont forget to clean off your nuts and bolts

[@reysdatnig]

Very nice and informational. Whats a good recommendation for ATF FLUID replacement? And is it 5 quarts? If i run into a problem i will comment about to do this job sometime next week

[@LostNCyberspace]

Man I guess I’m going to have to try this. 06 beetle. Very hard shifting after warming up. The fluid didn’t look awful. I can’t believe you didn’t take your watch off😂 If I do this I’ll give you an update!

[@lorirebisch4554]

Where is the link to the video where it shows the test drive of the bad shifting? Please reply. Thanks

[@donipasjaqa2146]

I have the same car I changed the filter and ATF when i star in the morning works well but when he reached the temperature 90 degree then he start kicking between the gears and when I put in Reverse do you have any idea about that .Thanu you if u respond me

[@pamelarichards6112]

Thank you, this is very helpful. will do the job myself -

[@RealOmarWahdan]

2009 VW EOS 2.0L Turbo having the similar issues on a hot day first gear when shifting down would jerk and shifting up from 1st feels off. Great video will update if it helped me out. 👍

[@living9377]

Will this be the same procedure on a b9 Audi A6 3.2 fwd cvt

[@rayonwilliamssportsandfun2106]

I replaced my valve body..and it still rev high and jump wen shift . Do u have re program the TCM after u replaced a valve body? P17F0 code pending inside the transmission

[@rayonwilliamssportsandfun2106]

@Clone Vision sold the car . No sense . Needed a transmission. Nissan are crap

[@jjsiegal1]

Do you have to reprogram the computer after the swap?

[@diaa_Alhamad_1]

Hey brother, I wish you could tell me how to fix the electrical wires in the Volkswagen Passat automatic transmission 2012 2.5

[@tube8533]

Do I have to reset the car to factory settings after the body valve is replaced? if Yes , how to reset it? thank you

[@omaridundua7191]

Hello, I have a problem with the gearbox lower gear lever, can you help me? golf 5 2.0 fci 2006

[@patriotprepper3878]

Is this basically the same as doing a 2001 Beetle 6 speed?

[@DavidRodriguez-gf5xy]

Yeah ,car company's have a tendency to re use parts ,basically u got the same car (attimes) just a different body style car, suv.. etc

[@popmajic]

My vw Passat 2007 has hard shifting when I accelerate hardly. But in normal speed it shifts good. Do you think it's because of valve body or solenoids?

[@RachelChavez1002]

Did you figure out what it was? mine is doing the same thing?

[@kmax7163]

Hell Yeah!! When the weather warms up I'll be changing my tranny fluid and filter but, if I need a valve it'll be golden thanks to you.

[@jackdanielspittman3456]

Which valve do you replace can you send a Pic and or location I have a 2006 vw cabriolet Trans code htu

[@jregamey]

Mine had crazy shift issue. But had a cel for input speed sensor. Ordered that. Mean while now only reverse works forward gears try to engage but fail.

[@davidforan298]

Thanks for the great video. My Jetta is doing the exact same thing. Can pin point the problem to when the step-daughter ran over a pothole and ripped open the oil pan. More than likely dirt got into the valve body and worked it destructive magic. Looks like a job I can do, not anymore complicated than jobs I have successfully tackled. Thanks again.

[@clayton9136]

Sounds like alot more than just some dirt. But allrighty david.

[@227johnb718]

How do I know it’s valve body vs transmission control module that’s messed up?

[@michaeldavidson8971]

My 2011 Jetta SE shifts terrible plus it sometimes jerks hard when almost at a stop. This problem is intermittent, sometimes it shifts great, the next day it will be terrible again. Is it the valve body? There are no codes for the transmission.

[@troywilson4694]

Ever figure this out?

[@edwinmorales9999]

Did you have re program the transmission if you that??

[@kirksunley1381]

Yes you will need

[@sabrinafelix2511]

How do you do this

[@h3adhuntersgaming546]

Hey I wonder if you have ever changed a valve body on a 2008-2011 rav4, awd, 4 cyl. I just dropped mine out(I had to in order to remove all the solenoids to clean them) I'm just wondering how the valves above it go back in, and there's a tiny black plastic piece with a spring and a small metal ball on the end, I'm not sure where it came from when i dropped the valve body out. If you have any advice id love to hear it.

[@derrickclark2707]

I have a 2006 VW Jetta 2.5 and it’s a hard shift when tying to gear 1-6 u change the camshaft speed sensor o2 down n Ik sensors crankshaft and other but it still won’t switch into gears need help

[@tarzan9833]

I got 2012 jetta s automatic i noticed delay in shifting when driving it’s taking to long to shift from 3rd to 4

[@Jasonjames1970]

I have a 2007 VW beetle and sure enough it hit 180000 kilometres and I was about to change the fluid and it started slipping it popped codes randomly that would sometimes disappear. P0731/732/. The service manual indicated the transmission fluid must be changed at 180,000 km I’m thinking maybe the computer push it into limp mode to force the tranny change? I can drive it but it won’t go past 80 km an hour and it slips on gears depending on whether it’s warmed up or not it really is not safe to drive right now but it is drivable. Any suggestions. I bought a $600 scan tool I figured it would pay for itself in a few uses and I got buddies that come over that are also into European cars I figured it’s a good reason for people to come over to come see me and talk about cars. Any advice would be much appreciated

[@tboneproductions2453]

Is that a Rolex?Lol. Thanks for the video

[@alejandroherrera4063]

Thank you guys so much! Your videos have been really helpful.

[@valdimicolchik7975]

To do such job You must to wear that half kilo watch ?

[@tonytrilex2555]

How do I know if the Valve body needs to be replaced or the entire transmission? When would you recommend the entire transmission being changed or just a valve body replacement?

[@inee107]

Tony Trilex i would do valve body first then if not fixed whole trans. 500$ vs 3-4k

[@jayfox5]

I have a 2006 Jetta 2.5 salvaged just picked it up from the auction. When it’s cold it’s fine when it’s hot 1st-2nd gear shift hard 3rd slips and reverse bangs hard also. Again when it’s cold none of that happens you think I need a new value body ? Thanks

[@arielban1]

more likely just solenoids

[@hassangooner233]

have you ever figured out the problem? I have the same issue😧

[@808kingkoopa]

Tcm most likely got water damage! Go to the junkyard and pull it out

[@MALUMEMALUME-mn9tg]

Vw polo 9n1 BKY engine 1.4 any video for removing solenoid and cleaning or replacing them?

[@MrSpyrrocko]

which problem do you have? which diagnose are tell you that guys? i have a problem with passat 3c 2.0 fsi 150 wen is warm then switch the 2-3 gear so heavy like a foot step in the ass .

[@urighht]

Hello so i have read alot of the comments, i picked up one from the auction 2005 2.5 automatic as well and same issues, i want to just do the solenoids which is even cheaper but learning experience for me, but my question is you guys took a used one from a parts car, how do you know thats good!?

[@fabmyride5181]

Ok it's a Golf but which year ? Some have the pan on the front

[@faraikaemba6594]

hie brother /2011 be gti transmission MMA my problem feels like the clutch is slipping at wide open throttle in 3rd, 4th,5th and 6th gear

[@yurrrrr6081]

Hey I got 2002 VW Passat V5 And the transmission clips plays up everytime I out in drive , What's your Ideas of replacing it ?

[@johndavid9478]

Where can the transmission output shaft speed sensor be located on my 2012 vw passat

[@tkpeters]

Output Sensor is above the Valve Body, towards the diff

[@Benardk4]

Halo, I have a mk5 Jetta 2006. It jacks then I accelerate past 1000 rpm or when in traffic when I shift from neutral and back to drive. What could be causing this?

[@joseespinoza-on8ve]

Hello from Mission Texas question ? vw beetle 2001 the ring that controls the speed sensor it doesn't turn , i lifted and turn the wheel on D and ring not spins what i have to do? thanks,

[@jedediahbc]

Thank you, a very informative video.

[@omarabdelaziz-el-ashry-Eg]

Morning. good job :) i have one promplem in passat 2003 1,8T 170hp , when I Press the accelerator pedal that I want cross someone in my way or I try to speed up fast the car make some kik or feel like some stone was front of my car and I drive over it. The oil is fine computer test was fine and I don't know what are this. Can you please tell me what can be this ?

[@houssamamhaz7994]

Hey, i have the same problem, could you please tell me if you fixed and how?

[@omarabdelaziz-el-ashry-Eg]

@@houssamamhaz7994 Fly wheel have to be change. Do u have automatic or manual gearbox?

[@johnlucas8978]

Hi, have a 2007 rabbit 2.5L 6 speed, but where can I find the correct Transmission Valve Body for this? EBay always says it is not compatible, is there another parts search site? Thanks!

[@mondo9.2.5]

ive seen some on amazon but not sure might just get it at autozone

[@fernandoalonso4068]

I DID THE TRANSMISSION VALVE BODY O A 2007 VW JETTA 2.5 ACCORDING TO YOUR VIDEO BUT I NEED TO0 REPLACE THE TRASNMISSION SPEED SENSOR FOR SAME CAR. WOULD YOU POINT OUT WITH DETAILS OF THE LOCATION THANKS IN ADVANCE

[@drjsantos15able]

Having what I believe is transmission issues on my Volkswagen cc 2013 with only 65k miles. It hard shift from 1st to 2nd gear. Not sure how to get it fixed without replacing the whole transmission. Someone told me to change the transmission oil and put the Lucas transmission oil slipping oil to help it out, had someone else tell me to change the valve body. And opinion #3 was to just change the whole transmission. Not sure what to do

[@MALUMEMALUME-mn9tg]

how should i know if the SHIFTS HARD VALVE BODY have a problem? what are the symptoms because i have my vw polo 16v auto when i have not warm it up it cant move when i am trying to drive it .

[@inee107]

MALUME28 MALUME28 replace trans fluid first, if not fixed then replace valve body, then whole trans

[@leonardsahidruiz]

I wasn't paying attention, and don't remember where did I remove a two or three long bolts from it,,,, there's like longer bolts, I don't really know where to put them back, can u help, or any ideas where to get info

[@leonardsahidruiz]

Use a nail o somenthing to measure the deep length,they usually go in tha higher side levels from the little towers above valve body

[@sabrinafelix2511]

Go online and download you a manual

[@aaiizee3]

Is this valve body video on an automatic Tran or a manual. If it is automatic can someone send me a link to the valve body replacement so I can buy it

[@kirksunley1381]

the valve body is what changes the gears in an automatic transmission and the gear selector (stick) that you choose is a manual, so you are the valve body in a manual !

[@joseaguilar4455]

Hi, I did exactly that but there is a problem, the bracket that moves the change of gears has a guide to put it so I did but for some reason can't move the shifter to pass the reverse what went wrong can you help??

[@HR-rt9nh]

i have a small slip in 3rd, you feel the car engage third the revs come down at same time then you feel a second lunge and the revs go up for half a sec, feels like it reengages 3rd. ive changed fluid, not flushed. fluid ok now before it was a little dark and short about 1.5 quarts (im guessing previous owner did not change correctly) so any ideas on shift issue? expensive?

[@rylasranch2995]

Do you have any vids installing it

[@janvercastroo]

Hey mate! That's the same transmission I have on my City Golf and I CAN NOT FIND the fill plug for this car. Can you please help me locate the transmission oil fill plug for these cars? Thank you

[@MikeR-yf5ss]

Drain plug is fill plug warm up and remove plug if drips/pours consistently levels good

[@janvercastroo]

Mike R thank you mate 🙏🏼

[@bloodbucket2847]

Wayyyy late but, not the drain plug, it’s on the side up by the cv joint.

[@sabrinafelix2511]

My 05 jetta the drain is the fill

[@englise-km8js]

gyuruben oraban dolgozo szerelo ez az igazi moetanabann gratulalok a mesterednek !!! ???

[@rhinotjaverua7007]

Hi! I'm stressing with not knowing on a 5HP19 auto transmission of Audi B6 3l V6 quattro. Which one is the shift selonoid A please...

[@shawnparasram5389]

Hello there i have had issues with shifting and Jerks in D , while brakes depress when heats up, i changed valve body with a rebuilt one, now the issue is gone in D with brakes depress but still jerks and shift hard esp from 1st to 2nd gear after heat up around 90 to 100C i tried to adapt and drive cycle but still same issue, any advise? car drives great when cold.

[@arielban1]

how do you know the valve body is good. Even rebuilt it could be bad. Only VCDS tool will tell you

[@ma7mody]

I'm facing same as your problem. My 2006 golf does hard shifting when gets hot and sometimes get stuck on 3rd gear. Changed the transmission with 2nd hand one and it's still doing the same thing. Any advice please help. Cheers

[@jareb71]

Mine does exactly the same. What was the issue @Ashour Noiya

[@ma7mody]

@@jareb71 ended up selling it as is. But before selling it, took it to a transmission mechanic and he said it's the " valve body " need to replace the whole thing and it will cost me $2500 AU dollars.

[@alankurdish9542]

Please make another tutorial about valve body GEELY EMGRAND EC7. Please many peoples has problem with engrand 7 valve body.

[@sprayg9763]

My 2011 Volkswagen Jetta is not moving in reverse when I go into reverse it just Rams up

[@velizeqiri9192]

hi i nead wiring diagram for automatic gerbox for jetta 2006 2.5 conector with 14 pin can you help mee

[@chatomoreno8027]

Hello nice video is that automatic transmission or stick shift

[@kirksunley1381]

manuals do not have valve body, you are the valve body with a manual

[@Heather-ti6wu]

Can anyone here tell me where the the transmission speed sensor is for a 2007 Jetta 2.5, thank you for your help

[@styloroc2000]

Did you ever find out? I have this exact same model, same problem.

[@kirksunley1381]

The lead with the two orange wires is the speed sensor...www.dropbox.com/home/09%20valve%20body%20bolt%20pattern?preview=20191014_125221.jpg

[@bestfights229]

I have a automatic 1.8 and it kicks in hard in 3gear could my tranny be bad

[@dane4890]

Fantastic, thank you!

[@Nicholasw991]

My 99 Jetta Mk3 only wants to go into drive, even in park. I turn the key to feel my vehicle jump forward, ready to take off, even the same for reverse and neutral. Couple days ago it didnt want to drive as if the trans just gave out. Turns out it was a brake cailber that locked up ( turned vehicle off in neutral before taking cailber off would not roll back freely, taking it off later that night allowed the vehicle to roll backwards ) any help is appreciated (:

[@boycott18]

Hi, I have a 07 vw jetta wolfsburg, csn I do this on my vehicle?

[@MrRoymi77]

I have the same car. Have you got any answers?

[@kirksunley1381]

I did it on mine...the video is good, however there is more to it than the video actually shows!

[@jimmiewilliams5972]

Question I have a MK4 jetta 1.8t transmission 09A I followed the video the install was not hard but the car will not move While idling brake pressed I can shift thru the gears but the car will NOT forward or reverse Any suggestion

[@sabrinafelix2511]

I have an 05 Jetta had a coolant box leak and need a new seals for the bolts that hold it in place and while I was at I went ahead and changed out the transmission fluid and filter because the car stopped shifting it won't go into gear forward or backwards or even when I go through the gears manually

[@MurphysMadness]

My 06 beetle is doing the same thing shifting too hard. :/ will be taking it to a mechanic very soon.

[@arielban1]

how many miles on the Beetle?

[@michaeldiggs5470]

I have 2010 va jetta, 2.5 motor. I came over hill and hit water about 40miles hr. It scared heck out of me. But I just kept it floored. It was up to hood. It sputtered but kept going. I drove next day to my son's 40 mile. And then it started missing. My brother said new plugs and censor said foul plugs. But then my transition started slipping 4 days later. My brother looked and my casing and filter was gone. Please help what should I do

[@808kingkoopa]

Tcu and ecm. I had to change bout on my passat

[@gustavohernandez8200]

the scanner shows on my jetta 2006 2.5 5 cyl the speed sensor but it has the same problem. shifts hard after 10 or 20 min of use . what do you suggest ? should i start with the speed sensor ? or should i buy the valve body ?

[@bryanshow2678]

Speed sensor is cheap and easy and if it’s throwing a code it needs replaced anyway. I had to change my valve body in my rabbit it showed no code on it but it fixed the hard shifting.

[@gustavohernandez8200]

Hey thanks ! I got the car fixed unfurtunately i had to replace the valve body and speed sensor too. The good thing is i found a cheap used valve and its working good now!

[@mikemcnaiey]

how much was the installation?

[@albertogonzalez3512]

I have a 2007 jetta 2.5 It was shifting very hard trust me when I say very hard I replaced the oil and filter(vw original brand) also add a bottle of (Lucas transmission fix) and thank God the problem is gone

[@gustavohernandez8200]

King Mike i spent around 400 dls for evrtything.

[@ginagutierrez7056]

My 98 is showing a po763 shift solenoid c. I need help

[@vgrof2315]

Very good. Thanks.

[@sincerelyyours8603]

hello I have VW pass at 2012, after 7,8 hours driving when transmission hot my transmission bun. what can I do? thanks

[@diaa_Alhamad_1]

And thank you very much for this

[@robertcruz6563]

I have a code error P0732 and my car will run fine once it warms after 5mins to 10. Couple shops told me I need a new transmission but I don't think I do could it be a computer system error or need new selenoid? Transmission fluid change? I never had it serviced sitting at 116k miles

[@audiogeek6430]

I’m at 113k and it was my solenoids with that code

[@kayilelana179]

My mk5 fsi 1.6 gears doesn't want to change it's an automatic

[@akliludebas9001]

Thank you for the video bro awesome

[@paulbusch3542]

I changed the VB, now Jetta won’t go in Drive. Only reverse and neutral

[@Prairiedrifter1]

I have a 2008 Jetta 2.5 and if I have to wait for it to get up to temp before I drive it or else it will shift hard from parking to reverse or drive. When I put it in drive I can feel it jerk when it goes from 1 and then to 2nd gear and so forth what I’m trying to say is that the shifts are rather abrupt when the vehicle is cold. Anybody else had this problem before?

[@manuelsarria1377]

Rivera I have same problem on my 2008 beetle. I changed oil and and fillter and it worked ok for about a year but now it’s doing it again I have 240 miles on the car maybe it’s time for new tranny???? Not sure what is wrong because some times it does not do it runs fine?

[@jonathanross149]

Try turning off the ESP and see if the symptoms go away. My wife's 2007 Jetta is doing the same thing, and I read somewhere it might "fix" it to turn off Esp.

[@arielban1]

@@manuelsarria1377 replace the oil again.. if gets better and comes back again, its your solenoids or valve body. One oil chnage is not enough.. more fluid in the torque converter that you cannot change by one oil change cycle

[@jacob6426]

I have the same year and also 2.5l Jetta with the same problem, I took it to a VW dealership and they replaced the valve body and now the shift is much more smooth. Comes at a cost though!

[@Farhad_ZKD]

@@jacob6426 How much did it cost you? My 2007 Jetta has problem too

[@blackericdenice]

Was that a paper filter or metal screen?

[@camerong5511]

I have a 2000 jetta 2.0 no turbo with 4 speed auto trans. When I bought the car it was rough had some extreme hard shifting. Replaced filter n fluids. Come to find that both of my cv axles were snapped clean in half. Just replaced the cv axels. When car is cold it will go into gears just fine but after warming up it shifts very aggressively in all gears. I have to have high rpms to get it to launch into gear and away she will drive leaving rubber n smoke on pavement and maybe a sprained neck. Someone please help me I'm exausted as to what the hell it is

[@camerong5511]

Also throws a code of incorrect gear ratio p0730

[@brandonromero8122]

Cameron Gergits did you ever find out what the problem was I’m having the same problem and code with my 2002 Jetta 2.0

[@DavidRodriguez-gf5xy]

What was it

[@kimbojanbranyan6352]

Thank u guys

[@stevennndeleonnn6726]

Hey I got a Jetta 06 2.0 turbo that I’ve brought off some dude in Craigslist. I’ve had the same problem of it shifting late when it’s been running and also the reverse goes out. Should I buy a new trans or replace the valve body. The car has 112k miles the transmissions shouldn’t go out that fast. Any recommendations?

[@arielban1]

if it were me, I would change the tranny and fluid at least three to four times. Look into changing solenoids first or valve body with solenoids. If when your car is cold and you drive it and it shifts through all the gears fine, it is more likely related to solenoid first then VBody. Good luck.

[@Santosajpacaja10]

My friend i have a vw beetle when the engine is hot the car going slow then star aceleran but not run normol

[@dorothyr5599]

I need help with 2006 VW BEETLE !!!!!

[@jarodmorris611]

Interesting to not show actually replacing the basic body, just pulling it. Yes, going back inn should be the reverse, but were there any issues that came up we should know about? I guess we assume there weren't since you didn't say so

[@sheilawong996]

Jarod Morris w

[@tonytrilex2555]

Also don't you need to add the new valve body and install with a torche wrench.

[@kirksunley1381]

@@tonytrilex2555 and preform a adaptation...other wise the computer will control the valve body just as it had been prior to the replacement!

[@Farhad_ZKD]

@@kirksunley1381 Do I need a special tool for adaptation?

[@vtraudt]

What transmission (tranny make, model, part number, code, etc) is this about?