Don't Crash Without These!! Ninja 1000 / Z1000 Frame Sliders

  Рет қаралды 9,054

Wrenchie

Wrenchie

Күн бұрын

Пікірлер: 23
@jot8686
@jot8686 Жыл бұрын
Thank you so much for this video, it was incredibly helpful!
@Reseiver
@Reseiver 5 жыл бұрын
Great video, thank you. I'm going to do some small mods to my new Kawa during the winter.
@Wrenchie
@Wrenchie 5 жыл бұрын
Thanks for watching and leaving a comment. Maybe you’ll share some picks of the mods???
@Reseiver
@Reseiver 5 жыл бұрын
@@WrenchieI'd love to. A few parts are ordered already and some will have to wait until spring. But i'll let u know when they are up. Sliders, crank case guards, anti-vibration pads for fairing, gear indicator and paint protection are on the list.
@Wrenchie
@Wrenchie 5 жыл бұрын
@@Reseiver Nice... my 2012 could use some new case covers due to the parking lot tip overs :( . The 2016 is still in good shape (hope I didn't jinx it). Look forward to seeing the results of your work
@NabilKarsheh
@NabilKarsheh 5 жыл бұрын
thanks for this video... mounting my puig pro frame sliders on my 2014 ninja 1000 is just ahead of me. This video helps a lot
@Wrenchie
@Wrenchie 5 жыл бұрын
Good luck and hope you never need to test the sliders!
@NabilKarsheh
@NabilKarsheh 5 жыл бұрын
Yeah thanks! Same to you!
@NabilKarsheh
@NabilKarsheh 5 жыл бұрын
Wrenchie they are on and again big thanks for sharing this vid! I chose the puig pro sliders
@Wrenchie
@Wrenchie 5 жыл бұрын
@@NabilKarsheh Nice! Well done!
@NabilKarsheh
@NabilKarsheh 5 жыл бұрын
Wrenchie and I subbed!
@ratkinson-uk
@ratkinson-uk 5 жыл бұрын
I looked at the cheaper dog-leg frame sliders, but any serious impact will bend the engine mounts and write off the bike. The official Kawasaki sliders and R&G mount to the front and rear bolts, so I personally think the extra £100 is worth it rather than potentially destroying the sub frame.
@Wrenchie
@Wrenchie 5 жыл бұрын
I understand your point. My goal was to protect during embarrassing topples... like in the garage. The 0 - 2 mph drops. I figure if I drop it at speed, the bike is toast no matter what sliders I have. Maybe I'm wrong but there ya' go.
@Truthasvictim
@Truthasvictim 2 жыл бұрын
Kawa sure didn;'t make it easy to remove or install the stupid fairing, did they? And for sure, the exhaust cover is absurdly difficult to assemble, had the same inufriating issue you did re-installing it. Good job though For the left side, you could have used a coloured marker to draw a little line on the frame and the other piece, and just align the 2.
@ghoutube
@ghoutube 4 жыл бұрын
Bro. I see u use torque wrench. How big the torque (lb.ft) to tighten it?
@Wrenchie
@Wrenchie 4 жыл бұрын
I just checked the 2011 service manual (cause its on my computer and I don't have to get up and go get the 2016 hard copy) but the lower engine mount It says that the lower engine bracket bolts (that's the bolt you replace with the sliders) are to be torqued to 36ft lbs. However, the torque table in the manual says 42 ft lbs. I think its 36 as nothing in the instructions is torqued to 42
@akarim909
@akarim909 6 жыл бұрын
What's the torque on the engine bolt?
@Wrenchie
@Wrenchie 6 жыл бұрын
The upper engine mounting bolts look like they are 44Nm. But you should check your service manual to make sure.
@shaymtbrider7244
@shaymtbrider7244 6 жыл бұрын
I did without taking out fairing
@Wrenchie
@Wrenchie 6 жыл бұрын
Yeah? I was really thinking about iut but the right hand engine bolt look way too long to remove without clearing the fairing. Good to know if you need to remove them for any reason! Thanks for the tip.
The Ultimate Sausage Prank! Watch Their Reactions 😂🌭 #Unexpected
00:17
La La Life Shorts
Рет қаралды 6 МЛН
PRANK😂 rate Mark’s kick 1-10 🤕
00:14
Diana Belitskay
Рет қаралды 11 МЛН
When u fight over the armrest
00:41
Adam W
Рет қаралды 27 МЛН
Ninja 1000 / Z1000 Air Filter Change Using K&N Filter
19:52
Wrenchie
Рет қаралды 17 М.
Kawasaki Ninja 1000SX OEM Frame Slider Installation
17:22
Blue Eyed Rider
Рет қаралды 9 М.
T-Rex Racing 2017-On Kawasaki Ninja 1000 Frame Sliders
8:27
T-Rex Racing Inc
Рет қаралды 3,2 М.
Z1000SX Service Series -Part One Remove Fairings /Oil and Filter
10:46
Fitting Kawasaki Z1000SX Frame Sliders
3:47
Dipscovery
Рет қаралды 4,5 М.
Z1000 SX fairing removal and frame slider installation
6:13
Solihull Bathrooms
Рет қаралды 12 М.
Rear Wheel Removal and Installation: Ninja 1000 / Z1000SX / Z1000
12:28
The Ultimate Sausage Prank! Watch Their Reactions 😂🌭 #Unexpected
00:17
La La Life Shorts
Рет қаралды 6 МЛН