Xantrex Freedom 458 Overview

[@willysunday]

Wow! I wish I'd seen this long ago. You taught me much more than I ever picked up from the owner's manual and repair persons. Thanks for this!

[@brandonburton9241]

I just bought a motorhome with the exact unit. This helped me with operating it so much. Thank you!

[@martinwaggoner9156]

Best informative vid I've seen explaining the basic remote panel functions (the written that comes with the unit is not clear "to me anyway")? And the explanation of how these units work is top notch, thank you.

[@ectjr100]

Got hit with a power surge and my 458 went dead, not only does it not charge battery and it doesn't invert but I also lost the AC pass thru. All ac circuits are dead in Rv. I have 12 volts from battery bank to inverter, I checked glass fuse inside unit which is good. I'm assuming one of the boards went out and was wondering if there is a common board that goes bad.

[@gracehardy4729]

Thank you again so much for your time to help us. The top breaker has never tripped, nor have we ever tripped even a 30 amp shore power breaker. It seems to me that a 30amp shore power breaker would trip if some power is not even going through the inverter and supposing that some power is going through the top breaker and enough going through the bottom breaker to trip it. Out of the ten receps in this coach, eight are labeled inverter. Forty-five years ago I attended electricity and electronics school in the navy before serving on a WWII vintage sub. It seems about the only thing that is still the same is Ohm’s law. You are very kind and whether I figure this out or not, you have been refreshing. But, you need to be about your regular work. God bless. Dave Hardy Sent from my iPhone

[@bigdawg7110]

I have two of these in my motorhome. Your video saved me from having to buy another unit. My AC pass through fuse was blown. Thanks.

[@onetonf350]

I just replaced mine with a new Xantrex model 81-2010-12. Goes into a 1999 National Tradewinds RV. The old one had the two circuit breakers on the front and the new one does not. Doesn’t seem to matter though. I was able to switch it out myself and it immediately works properly. The old one had been bypsssed years ago and an Intelipower 9100 was just screwed onto as a battery charger only. It feels good to have this working properly again.

[@richdemarti]

Excellent video! Thanks for taking the time to produce these films. I have an older Xantrex 2412 (might have the wrong model number...2400W-12V) that was installed in a log cabin I bought in 2018. In the summer of 2018 I had a swamp cooler running on the front porch and water leaked through the floor boards of the porch and got into the inverter located below the porch in the basement. The generator was in service at the time of the incident. The inverter quit working of course and now when I test start it it gives an error code which I believe means the transfer relay didn't switch to the "invert" position. I've had no luck trying to either buy the right part or finding anyone interested in trying to fix it. I've been getting by with a smaller cheap inverter 1000W and a couple battery chargers. I would really like to get it fixed if possible since I took the cover off and it doesn't smell or appear damaged. The cover and all is currently all back together properly.

[@pcselectronics5423]

Send model number and photos to [e-mail] or call 573-814-3131

[@Kiptanui]

I’m a Mobile rv mechanic, and I consider myself a decent one too, but I just learned something on your video. I love that crap! Good vid!

[@pcselectronics5423]

I am learning all the time. Thanks.

[@wilmajensen]

Great information!! Thank you for all the explanations of how it all works. We are currently having issues with ours - I'll give you a call tomorrow to discuss.

[@AmericanJustice22022]

Thank you thank you than you very very much I could not get my batteries charged, after a few minutes watching your video, you showed me that hidden button under the neg cable that I didn’t know was there, I checked that inverter over and over but couldn’t find the reset, Thanks again!

[@ImpalamansGarage]

Very informative. Just bought an RV with one of these units. My breaker on the front (30amp) is popped out for some reason. Let the troubleshooting begin. 😁

[@803mastiff9]

Are there any remote panels other than the basic remote that work with Freedom 458? I read in a xantrex manual the Freedom X /XC remotes work, however a xantrex phone tech informed me it des not? He also said the basic remote is the only remote that interfaces with Freedom 458.

[@donnyswanson887]

I just found (and subscribed) to your channel, your understanding and ability to explain these inverters is truly impressive. I'm wondering if you can lend some insight into an issue I'm having? I have an older (2003) freedom combi. The inverter keeps turning itself on and drawing the batteries down. I've owned this RV for the last 12 years and don't remember this issue prior to about three years ago. Any advice you can give would be greatly appreciated. Cheers! As a side note, mine doesn't have the two breakers on the front of the case like the ones in your video

[@dondonaldson1684]

Excellent video, thanks for the detail. In your third way to turn the inverter on, you plugged into the aux input. Could you please let me know what the plug part number is? My Freedom 25 is mounted in a tight spot on my boat, and this information would save me from trying to squeeze myself into a spot close enough to guess what it might be. If you can respond, that would be very helpful. Many thanks!

[@tedreed1201]

Thought I had a problem! It would cycle on and off …. It was the power cord to the boat was burn .. made me happy to replace cord….

[@user-mn6xb1do6h]

Very imformative, ihave older model with a failed control board, can new model board work in the old unit?

[@WilliamMattish]

I just got a 458 2000W with a problem. I am able to troubleshoot myself but would like to get some schematics or at least know where to look for the symptoms I have. The inverter is not working and the symptoms are a blinking Charge LED and a blinking Low Voltage LED. Both are blinking at the same rate. The DC voltage at the terminals is the Normal 12.6v. Any help would be appreciated.

[@dam4586]

Great and very informative. I replaced a 458-2000 with the remote control. I went with a 458-2500 2channels in and 2 out. The original problem was charging but not inverting. Line power went in, and charging seemed normal (lots of buzzing, but you told me the 30 amp setting made it charge a lot). That might explain why the seller of this motorhome had gallons of distilled water on hand. I'm afraid to make the same mistakes and damage the new inverter. I took the old one apart and found visually that most or all the transistors on the inverter board had shorted, melted down, or blew up, still bolted to the inverter heat sinks. What do you think may have caused this massive destruction of the sine-wave power out components? Could they have back-fed AC into the output? I'm not really confident in the delay (break before make) functions of the transfer switch. It seems to delay a switch bringing the generator on-line, but I'm afraid to invert while applying any outside power source, line or generator. Thanks for the confidence in shutting off the inverter by just pressing the invert button on the remote. I can then start the generator and some air conditioners with it off. Any thoughts about all those burned up transistors? Have you seen this before? Thanks. Don

[@fauxpainterartistbestinnev1851]

this is a good video. I bought a motorhome . I wanted to understand this inverter that is in it. Thanks for the class./

[@3sons66]

WOW! Just replaced my Xantrex 458 due to charging issues to by batteries. Was only getting 11.4 amps out to house batteries of my RV. 110-115 V shore coming in and only 11.4 V to batteries. New one installed and fixed the problem. Wonder if these can be refurbished or is it a throw away item??

[@weaslenut]

Hi, have you replaced the transistors on the inverter board, and any suggestions. I plan on doing it as I have on vfds I work on and would appreciate any guidance!

[@wendellgilbert8374]

The manual states that this unit needs to be mounted on a shelf. Do you see a problem mounting this on a wall ?

[@brentbeckman5643]

Very informative and great tutorial 👍

[@michaelclowser]

I have this unit in my motorhome and when I hold the invert button, the invert light blinks once, it kicks on for a second then the charge light blinks about 5 times and then it goes out. If I am hooked to shore power the charge light does come on and it charges the house batteries only. Can you help please?

[@shawnmol3669]

Hi I have the same invertor. It recently stopped switching when I am plugged into shore power I have no power to my 110 plugs unless I turn the invert on... Any ideas?

[@TravelingRandall]

Very informative videos - thank you. My Freedom 458 Model: 81-2021-12 Date: 20 - Feb 2004, when I am driving my motor home - it charges the house batteries. When I am on shore power it does not charge my house batteries. Can you suggest what I should check?

[@edsteinbeck8090]

Where is your shop located. I think my Freedom 458 is over charging my batteries. Batteries were installed in 2-21.

[@therockinrv602]

Wow, great info, thanks!!!

[@francornwell4073]

Hello, I just watched your very educational video on the Xrantrex 458 and was impressed with your knowlege . I have that model in my motorhome and it works great. I have a battery voltage display that normally shows my battery state such as 13.20v, etc. Lately, when I check my display, it flashes the 13.20v then goes to 6.0 v dc. I don't know how this happened but I would like to get it back to the 13.20v display as this allows me to know when my batteries get near the 50% range of 12.10v. This new display doesn't mean anything to me as how low my batteries are. I don't know if resetting would correct the problem but I couldn't find anyway to reset it. As I mentioned, when I push the display switch, the 13.20v flashes but the goes to the 6.9 v dc mode. Thanks for your efforts to educate us. Sincerely, Frank

[@pcselectronics5423]

I would check all of your battery connections. Loose wires or corrosion can cause strange problems. If all is well with the batteries the display may have a problem.

[@AngelLopez-sx6vo]

Wish to know wy mine is not turn on without battery terminals I have checked my power 110 v at entrance is 110 but wires goes to transformer ðo not have any power Then review my fuses and both are OK Will you give me and advise to çheck

[@michaelcowanmichaelcowan969]

I have a 458, its not charging or inverting. If i replace the internal fuse will it fix this?

[@jimmylivrieri7525]

Does this work on lithium ion batteries? Is there somewhere I can do a conversion if not

[@robhendrix8020]

I have a freedom combi 458 inverter/charger that is stuck in gel mode. I think it might be the 20D since it has 20 and 15amp AC out flip fuses and 25 Amp inverter/charger pop out fuse. It won' switch mode to wet cell mode. I tried unplugging shore power and removing house and chasing batteries and red and black terminals for several hours to charge batteries outside the RV but no change. Any suggestion on repair of a board or what board to replace? I've repaired a broken traces in a couple of refrigerator eyebrow cards before and have some beginner soldering skills. Thanks for your informative videos.

[@ceeferr106]

HELP … AC in light no longer on after park replaced 50 amp breaker on post. It doesn’t light even if I use dog bone to use 30 amp on post, nor when I fire up generator. I have a fluke but ignorant on use. Desperate for help troubleshoot to save this 1 week beach vacation. I suspect I’m using battery even though I’m connected to pedestal. Will pay for resolution and hand holding for fluke settings and placement. Tiffin 2004 phaeton, xantrax 458 25 button bottom right is in, inverter light solid, charger blinking indicating no AC current but safeguard at pedestal says all go and alive no faults (using 30amp dog bone to 50amp surge protector , will bring in slides tomorrow (if possible) to try different pedestal) two top green lights inverter solid and charger blinking and right two lights dark. Freedom remote installed inside cab). Removal of front center bottom plate doesn’t look cooked or disconnected wires but not going to poke around without direction. All was well until 50 amp pedestal breaker barfed which threw the safe guard surge protector to issue a neural fault. I do not know how to set fluke setting or placement to check breakers.

[@Stericdesign]

If I followed you correctly in order for my charge to work I need to keep the inverter on?

[@decathelondave9340]

Thank you I now know that my freedom 458 works I pushed and held the invert button and walla it works. I have a Xantrex panel inside my motorhome but it does nothing . Do I need to start looking for a new one? Or should I send it to you to look at? I'm happy to pay. Dave G.

[@jamesburgess85]

Thanks for this info

[@jasonfrodoman1316]

Is there an easy fix for a backfeed fault ? I cant clear the fault. I found blown relay on AC board. Replaced that. But still shows a fault when AC in is present. Unit inverts with no issue. Lots of buzz. But if AC in applied no good.

[@frednick5443]

I have this same unit. I’m actually thinking about upgrading my battery bank to lithium. Can I still use my Xantrex Freedom 458 inverter with lithium batteries?

[@pcselectronics5423]

As we all know you do have to be careful with lithium batteries. Normally the answer would be no because the Freedom unit does not have a constant voltage/current setting but, if you buy lithium batteries that have internal management circuitry then it should be ok. Be sure to check with the battery manufacturer about this.

[@frednick5443]

Excellent! Thank you so very much!

[@coreybabcock2023]

Yep mine would buzz like that miss it alot

[@toomprakobkij9654]

On my unit the charging indicator light has never lit up on the panel and now my house batteries are dead. can I assume my charging portion is not working?

[@coreybabcock2023]

Wish you could make more videos

[@jesuscandelaria6228]

I have a main breaker box should I hook the two output into the main breaker box same size Breakers and hook both of them there or what should I do

[@pcselectronics5423]

A very strange problem. I would check to make sure it is not in the 'search watts' mode. Or it may be a loose connection that is being effected by the movement of the breakers. Switch off all input and output breakers an check the wire nuts inside the AC wiring compartment. After that it may be a bad relay solder connection on the AC power board inside.

[@tombrockwell6961]

PCS Electronics I was thinking I needed to replace the unit? Maybe send to you to look at, the fan would never come on to cool the unit, assuming it has a heat switch somewhere. I opened the unit up & discovered the fan works so I moved the wires to the outside & run it manually now.

[@tombrockwell6961]

How do you telll if in the search watts mode, I have the remote package in the coach.

[@pcselectronics5423]

With no load the inverter will make a ticking sound. If you put a load on it like a 100 watt light bulb the inverter will come on. TVs and appliances like microwaves often will not start the inverter. The search mode can be shut off with the remote. Hold the setup button until the lights change positions. Press the invert button multiple times until the light is at the bottom

[@bobmay9887]

Awesome video pure information so as i live in my MH shipping it is not an option.. how about i come to you

[@robertgregory2618]

What is your opinion of the Xantrex Freedom XC 2000 watt 817-2080 charger- inverter. It's for a Ford Transit van conversion? Thanks....

[@randysautocare6390]

Does the inverter control shore power? my control panel state waiting for AC

[@chaserivers4058]

I have a rather unique question that I can’t find in the manual/internet. My RV is using a Bi-Directional Isolator Relay Delay (BIRD) as a controller to activate a relay which is designed to connect to house and chassis batteries in order to charge together. On the BIRD there’s an input for genset, which is to disconnect the two sets of batteries when both the engine is running (alternator charging) and the Xantrex is charging so the two are not fighting each other. So the question is: is there a way to get a 12v signal out of the Xantrex when it is in charge mode? If I have to solder a lead to the circuit board, that’s fine. Thanks and great informative video.

[@pcselectronics5423]

You could tie across the charger relay coil. It is a 12 volt coil and is the relay toward the top of the unit that ties to the red wire coming out of the transformer.

[@napkinband]

my 458 works fine but remote went out no lights nothing new remote and wire same thing whats wrong and is it repairable?

[@marcoknight4154]

Can this unit be programmed to auto start the gen when it detects batt low?

[@dice12tx]

This is an awesome video. I have the same interview/converter. I do have a question: When plugged into shore power, is there a reason to keep the Inverter on? I noticed that around 13:40 of the video when you explained the charging function, you turned on the shore power and the inverter light was on, on the remote (and blinking in standby mode). On my motorhome, when plugged in shore power or the generator is running, the Inverter is off. Im thinking the inverter would be of use for boon-docking or loss of shore power. Or does it hurt to keep the inverter on and just let it stay in standby mode?

[@pcselectronics5423]

These inverters are designed to be on all the time. The only reason to shut them off would be if the RV will not be plugged in during long term storage.

[@jimmylivrieri7525]

Can I run my air conditioner on that?

[@kevinbemrich8672]

I have a freedom 30 marine combi, i think I’ve done everything to get to invert, but no output, the remote lights up as stated in the owners manual, I’ve installed 6 new, 6 volt batteries, they are connected correctly. It is not in search watts mode. I bought my houseboat and the inverter was factory installed, but it was not used by previous owners for 8 years. The inverter is 18 yrs. old. Assuming it is a problem with the inverter is a inverter that old worth repairing,

[@pcselectronics5423]

These are good units and usually worth repairing but 18 years is a long time to be near the water. The unit my have a corrosion problem. If you open it up and it looks clean inside I would fix it. Otherwise get a new one. They still sell this exact model which makes it easy to swap out. If you would like us to repair it call 573-814-3131.

[@HARRYRUSHAKOFFBONGOLOID]

How long is this guy going to talk about the battery temp location where you can put it and where you shouldn't put it

[@carpenterfamily6198]

So when using the aux switch to turn on, What config settings does it use ? Would those setting have been previously entered using a remote and then retained on a PCB inside ? Also if I remove DC, are the settings lost ?

[@pcselectronics5423]

Yes it will use the settings that were previously entered and yes it will lose the settings when the battery is disconnected.

[@olvano]

xantrex temp sensor what's the resistant of the yellow and the black one

[@revfredl]

I have this same inverter. I have old house batteries that I'm fixing to replace but right now my fridge indicator is flashing Lo/AC. When I run the engine the fridge indicator goes off. I have the same remote panel as you were showing but my inverter only indicates 10 and won't go any higher. Also, my batteries are indicating at full. Any thoughts would be greatly appreciated.

[@pcselectronics5423]

Refrigerators are not usually connected to the inverter so you should check this by switching off your inverter and the inverter input breaker. It does sound like the inverter is not charging the batteries. So again check the inverter input circuit breaker in your AC electrical panel and your inverter battery fuse. After that you may need to go inside the inverter to check fuses or send it in for repair.

[@charlesbologna4979]

This is a great video. I have the Freedom Combi in a 2002 motorhome and the Remote stopped working. Completely dark. Inverter and charger still work fine controlled from the front of the unit. I have tried a replacement cable with no luck. Is there any way I can isolate between the remote being bad vs the control board being bad? Or is there anything else you can suggest that I can try. Thanks in advance.

[@pcselectronics5423]

If you know someone with a similar unit you could test it with theirs. Or you could send us the remote for testing. PCS Electronics 573-814-3131

[@crosstownpete]

I have one that needs fixing, where are you located please.

[@enriquesanchez3519]

Thanks for the video!!! Question my inverter is working and powering certain outlets and I'm getting shore power to my breakers but not to the rest of the outlets. I Replaced 3 gfi outlets and still nothing. Is their something in the inverter that could be bad that would interfere with the rest of the ac outlets?. New transfer switch as well

[@pcselectronics5423]

If you are getting power to your TV, microwave and kitchen outlet then the inverter is ok. If not then there is a problem with the inverter pass-through relay. If the inverter is ok then changing the transfer switch should have fixed your problem. If you have an Intellitec EMS system then the problem may be the relay for that system located inside your AC breaker panel.

[@mariecollins8500]

I keep blowing the quarter amp fuse on the ac board. (no batt. charging) Unable to find the proper slow burn fuse except on amazon and the quality is bad. Even tried the half amp',same deal. What does this fuse protect? What could be causing it to blow? The first fuse lasted a good five minutes so its not a short. What am i endangering by bypassing it? Also if i remove the entire unit for service would i be able to still use the 12v house system temporarily or does it run through the inverter? Thx . btw--great video

[@pcselectronics5423]

The fuse protects the small AC input transformer which powers the inverter circuitry when on shore power. The transformer is probably going bad or you have a problem on one of the systems that the transformer supplies. Bypassing would just cause the faulty element to burn up. The inverter is the charger so to continue to use 12 volt power without the inverter you would have to connect a battery charger to the batteries and keep the load at or below the charger output power.

[@FranklinVideoInc]

I have a freedom 458 that the inverter is working, but the charger isn't. I press the setup button to make it charge at about 13.5 volts. After about 5 seconds it quits charging. Well, the remote panel indicators above voltage light in amber to the level of 12.5 or so.... probably what the batteries are reading. where should I be looking for problems? I have removed the unit from m y motor home... and have the case open. AC board?

[@pcselectronics5423]

Yes the problem is most likely on the AC board. You are looking for a blown fuse, bad solder connections or the small transformer may be bad.

[@douglarue8485]

Thank you that was a great walk-thru. Would you know if it is safe to operate the freedom 458 with shore power(120VAC) and without a battery connected? ie as a converter just powering the DC for lights and the minimal DC needed for Norcold fridge operation? The batteries might be out for servicing or being used in another device? Thanks.

[@pcselectronics5423]

I have run them on the bench this way for short periods without any problems. Some inverters will not pass AC without a battery. Some inverters will run what is called 'dead battery boot' so you will still have power. It should not hurt anything to run it this way.

[@douglarue8485]

@@pcselectronics5423 Thank you, I will try it then and test my AC then watch the 12V line and hope it settles to ~13.5VDC. Only then will I try some lights and light loads to see what it does. I really didn't want to damage it so appreciate your answering the question. :)

[@chrissramek7035]

I have one of these in which the pass through and charge function stopped working. I opened it and checked the fuses and inspected the components for swelling or any visual clues to no avail. Any thoughts?

[@pcselectronics5423]

Watch my video kzbin.info/www/bejne/gKSlpGptecZ_eLc Need to check the internal fuses. If it is not a fuse then it is a failure of the AC board. You can send the unit to us for repair or if you are in Missouri you can bring us the RV. Call for shipping instructions or an appointment. PCS Electronics 573-814-3131

[@stevemartin1164]

Good afternoon PCS. I have a Freedom 458 that is not charging the batteries. The Inverter is working fine. The remote control panel is showing the battery state in red as empty. The batteries are new and fully charged. DC volts are showing 12 v. With the batteries disconnected I get a reading of zero dc volts. I removed the unit and checked the internal fuse. Checked good. What else can I check before I ship it to you for repairs? Thank you!

[@pcselectronics5423]

Always check you battery fuse first. This is the large fuse near the inverter or in the battery compartment. Be sure you have AC in by checking your 30 amp breaker in your circuit panel. There is also a push button breaker on the front of the unit. Call us if you want to send it in for repair. 573-814-3131

[@tombrockwell6961]

I have the older heart freedom combi,, every once and a while it will guit making 110 power, I go out to the unit and turn the two output breakers off & on , this seams to solve the problem until the next time???? 1998 year

[@jamesgorski3931]

My fault light keeps coming on On remote board it is reading 15+ volts I have tried to reset by unhooking battery post & unplugging remote connector on the unit. I hear the unit humming but don't hear the fan on thinking it may be a fuse or something inside. Have you any thoughts on my issue.

[@pcselectronics5423]

It is strange to have the fault LED on but the unit continues to operate. I would monitor the system to be sure all is well and the battery voltage drops when it is done charging. Maybe a controller malfunction.

[@patrickpeterman4890]

I HAVE A 2000 WATT 458 FREEDOM COMBI WITH THE 458 XANTREX BASIC FREEDOM REMOTE; I WONDER WHY THE INVERT L.E.D. IS LITE READING

[@pcselectronics5423]

Normally this light is only on when the inverter is on and you are powering a load or if you are on shore power and the battery is charging. This light is telling you that the charge current is less than 10 amps and the batteries are almost fully charged. The invert LED should only be on when inverting . If your remote is not working correctly you may have a bad serial driver IC on the control board. Call if you have any more questions or need a repair. 573-814-3131 9-5 M-F central time.

[@patrickpeterman4890]

Thank,s for getting back to me - I will give your company a call; much appreciated; Patrick.P

[@paqattack15]

Any trick to engage the charger I push the button and the charge doesn’t come on and the batteries just drain ....

[@pcselectronics5423]

The charger should start automatically any time AC is present. The button only shuts it off. Check your battery fuse and AC input.

[@stephenkeller1347]

My 458 doesn’t have output circuit breakers on the front. Where would they be?

[@pcselectronics5423]

There should be a separate sub panel with breakers for the inverter only. Sometimes this is located near the inverter or it may be near your main AC breaker panel.

[@scottmilligan1087]

My unit melted what I think was a capacitor right next to the breakers. The board is labeled Z1. Can you sell me the part and could this have been caused by a power supply without a neutral? I have my RV plugged into a welding plug (2 hots and ground) with a converter plug to 14050 plug. Thanks.

[@pcselectronics5423]

Thank you for contacting us with your issue. The parts you ordered should solve the problem.

[@gracehardy4729]

Thank you for the video, it was very helpful. I have the same unit and the bottom output breaker trips often. The coach is 50amp, but even plugged into 30amp service, the bottom breaker trips. One RV tech told me it may be weak. Can you show how to replace the breakers and where to get them. Also, could the wires from the breakers be switched at the ac breakers in the coach so the top and bottom breakers trade loads? They are both 20amps. Thanks so much.

[@pcselectronics5423]

Yes you could swap the circuits to see if that solves your problem. Changing the breaker would require the removal of the AC board which is not very easy as there are a lot of wires to deal with. I do not have a part number for the breakers at this moment I will see if I can post one later.

[@gracehardy4729]

PCS Electronics Thank you for the quick response. I am sure you receive many requests. We have a 2005 Allegro Bus that we purchased five months ago, but we have more electrical issues with this 50amp coach than I had with my 30amp Fleetwood Discovery. By issues I primarily mean the breaker problem. In fact, I don’t understand why there are just two 20 amp breakers on the Xantrex for a 50 amp coach. Does all the shore power pass through the Xantrex? Thanks again so much.

[@pcselectronics5423]

No only a few items are connected to the inverter. Usually they are the TV and stereo system, Microwave oven, and one outlet for the coffee maker. Sometimes the refrigerator if it is not a residential model. Air conditioners and most outlets and battery charging are straight to shore power. The part number for the 20 Amp circuit breaker is: CA1-B0-24-615-121-KG but none of the distributors I checked had them in stock.

[@slimdusty8718]

Nice video! I have been messing w a freedom 10 that i just got and hooked up 220 on accident. Everything seems to still work perfect expect it is not letting the ac shore power through anymore. Most people on the forums agree at this point that the transfer relay has to be the culprit. Even w a dose of 220 my fuses were not blown. Any help is appreciated and if I can not get it where are you located? I can't find your shop location or contact info on here. Thanks again.

[@pcselectronics5423]

The transfer relay runs on 12 volts and would not be effected by the over voltage event. Most likely it has fried your input transformer. We can change this for you if you send us the unit. Give us a call to discuss it. 573-814-3131

[@ryanhillman5126]

Hello, need help how do i find you for repair ? My charging just keeps flashing showing no a/c power coming in.

[@pcselectronics5423]

Call 573-814-3131

[@sidclark5018]

I just bought a boat with this unit installed. My question is, is there any way to stop the buzzing sound?? It's driving my wife crazy. Is this inherent to this unit?

[@pcselectronics5423]

Yes they all buzz a little and it may get worse as the unit ages. There are some rubber strips installed between the cover and the chassis of the inverter that reduce noise. These may have fallen out. You can also just shut it off at night if you have enough battery to last that long.

[@MrBillygoat]

I loose AC to all my inverter 110 outlets in motorhome while generator or shore power is on, but turn AC off and inverters turns on and all the 110 outlets work... is the automatic transfer switch in it bad ? I have a xantrex 458 inverter/ charger , thanks for any help you can give me

[@pcselectronics5423]

This means the transfer relay in your inverter is not working. There are a number of reasons this could happen. There are internal fuses that could be checked if you are ok with going inside the inverter. Be sure to disconnect the battery and all AC power must be off. If they are ok the unit will need further service.

[@MrBillygoat]

I figured as such , I ordered a brand new 458 to replace , it’s 14 years old

[@MrBillygoat]

Both internal fuses were good, we have 110 coming in but not out. Only on 12 volt invert mode do we have 110 out to the coach

[@MrBillygoat]

Put new inverter on today , that fixed my problems. Thanks for your advice !

[@pcselectronics5423]

@@MrBillygoat call 573-814-3131 if you would like us to repair it.

[@jerryjensen2611]

Thanks for the video. Very helpful. I have another problem. I have a Xantrex 458 / 25 that won't charge the batteries. The light fault code is this. CHARGE LIGHT BLINKS ABOUT 1 BLINK PER SECOND AND THE LOW BATTERY LIGHT FLASHES RAPIDLY. The manual says only, "Battery Ripple" and "Warning". Could you possible give me a direction to go. If I can fix it myself (fuse or something simple) that would be great but if its the inverter can I send it to you to be repaired? Thank you so much for your help in advance.

[@pcselectronics5423]

If it is in fact a battery ripple warning then you need to check for loose or corroded battery connections. If everything checks ok then the control board may have a problem. In that case you would have to send it in for repair. Please call for shipping instructions. PCS Electronics 573-814-3131

[@lynialwells1772]

How can I contact you about repairing my Xantrex 458 it has a manufacturing date April 2004

[@pcselectronics5423]

Call us at 573-814-3131

[@ElTerricolacatracho]

Where can I get a holder remote control panel, like yours.

[@pcselectronics5423]

Built this myself with an old Radio Shack project box and some surplus handles.

[@brentbauman3686]

Inverter wet flashing

[@gailid]

Hey, Thanks for the great video. I have this same unit, and i'm having an issue with low voltage output. I called Xantrex and they gave me the typical "your meter is probably not reading the modified sign wave" responce. But, I've had my industrial electrician father-in-law test with his fancy meter, and it still shows between 98v-107v. Also, I know something is not right as my CPAP machine (which has worked off this inverter in the past) will either not power up, or will power off as soon as I engage it. When i try to search for anything about low voltage on this unit, I only get the same "meter can't read a Modified Sign Wave" conclusion. Any ideas? Also, every time i open my battery compartment, i feel like there is a lot of leaked battery acid. Any chance these issues are connected? Also, we just discovered that a wirenut in my fuse box was melted. One of the wires had a pre-printed "shore" lable. Not sure where in the chain this connection was in reference to the transfer switch, but the 2 wires were barly touching. I'm sure that wasn' helping.

[@pcselectronics5423]

You may need a "True RMS" meter to get a correct reading. Another reason is that it is in "Idle Mode" (sometimes called "search watts"). Place a load such as a 100 watt light bulb or a small space heater on it while you are taking your measurement. If you shut off the Idle Mode feature and you still have a problem it may need service. The battery leakage could be caused by overcharging. You will have to monitor the battery voltage during charging and be sure it drops down to float after no more than two hours for a 400 amp hour battery pack (four batteries). Check the amp hour setting in the "set up". All of this should be covered in my videos. The bad connection you found would only effect the battery charger and pass through AC. The battery charger can draw a lot of current for a long period and can melt bad connections.

[@gailid]

PCS Electronics thanks for the reply. I’ll try adding a load to it. But, we have tested with a true sign wave meter.

[@dimitris1453]

Hi your web don't come up is it still active

[@pcselectronics5423]

Yes it is still there. www.pcselectronicsmo.com. Thanks for watching our videos!

[@760extra330]

Can you send me your contact info I have a freedom 458 as well and need it repaired. Thanks

[@pcselectronics5423]

PCS Electronics 3900 Brown Station Rd Columbia MO 65202 Phone: [phone]

[@user-wt6vb9ou8e]

Hello, Are you still doing these Inverters? I see this video is 6 years old already.....Thanks