XD falcon repairs

[@kpfpv8515]

"Like a mad women's breakfast"😂 Keep them coming Graham 👍🏻

[@knight2425]

I’ve watched quite a few people working on cars on the net and you are one of the few that has the guard on the angle grinder 👍

[@xacoupeguy]

cheers for that!! they put those shields on for a reason not just for decoration

[@daviddeakin2006]

Hi mate , none of your videos are terrible. Thanks for sharing how you tweaked the boot lid that was gold .

[@phatridesgarage3760]

Great fix on the XD boot lid. Your videos are getting better all the time Graham , brilliant fixes and explanations and "unbeatable one liners " and very smart uniform

[@joe2097]

Man your vids are awesome I like how you take the time to explain why and how I listen intently to every word

[@georgehatzi6625]

Nice work.

[@maxrockatanksyOG]

Love the XD stuff; back in the day (early 2000's), i bought a 40ft shipping container off a bloke who worked at J.T Fossey Ford in Tamworth. I bought an ex NSW Highway Patrol car with genuine 351ci + single rail with blue interior trim (had the ESP F+R seats thrown into it at some point); There was enough NOS panels (3x entire roof panels, both rear 1/4's times ALOT, beaver panels out the whatsit, and roll pans for days); there was also bulk shitton of NOS XD/XE/XF interior & exterior stuff in the container. Ended up doing a Tafe repair course, stitched on the new panels and also learnt how to lead wipe by the teacher (who later on, got done for fiddling with kids...) By the time i was done- it had a 383ci stroker & Jericho air assist 4 spd from a wrecked Mustang i bought in from the US. It was a fucking pig to drive on the street, but motored on the strip.

[@GeeenJ]

never too long on the vid's graham always enjoy watching you work that dog leg section what i've done on similar repairs is fold a edge then use braze to weld it leaving a slight gap for the braze to melt into then use a 1 mill cutting wheel to grind the seam in to the braze so it looks factory i've had to do cuts like you did on the boot even when fitting other panels i found they vary even if the cars had no accident damage seems they still fitted panels to match each body like in the 50'swhen they made the 70/80's cars

[@Millasturt1420]

Awesome mate 👌

[@VCCOMM]

top tips again , and no not too long , was just getting into it lol . keep it up there lad . lot of talent for a young fella

[@STREETCARCULTURE]

Nice one Graham 👌🏽

[@xacoupeguy]

Cheers man!!

[@adelaideinvigilation5230]

Escorted tours with expert narratives around the Birdwood Motor Museum, now that sounds like an interesting way to spend a morning.

[@Carsnbikes73]

Great to see literal panel beating in this video 👍🏾

[@XEFairmont]

Love the attention to detail on the boot. Top rate Graham. And you're dead right these poor old bangers were built by ordinary folks not Peter Thomaseni

[@stevendurieu6938]

Good vid i like seeing xd stuff i have one in my hored of cars 😁 i haven't noticed the little sticky guy in a while

[@Drifterdan1]

Loved seeing how you "manhandled" the boot to get the fitment mint. I always wondered if panels could be smacked around a bit to do this, and apparently you can haha. Any chance you could show us how you do the brass welding (maybe even a Patreon video)?

[@xacoupeguy]

Thats a brilliant idea all I gotta do is figure out patreon haha

[@shaneyule3484]

good 👍

[@lachlanwoods3940]

Smashing! Good vid mate, question, how to rectify if the boot lid sits a little high at the back 2 corners near the rear screen, gaps ok otherwise but both corners sit up??? 🤔🤔

[@xacoupeguy]

Its very hard to describe but easy to show basically open the bootlid and push up till the hinges bend the bootlid frame

[@lachlanwoods3940]

I will give it a whirl tommorow mate, thanks for the tip, keep up the brilliant work!! 👍👌👌

[@benni727]

is that xd a factory v8 4spd one. it seems like alot of work has been done especially if it was only a factory 6cyl

[@xacoupeguy]

its a factory v8 ex NSWs highway police car factory 351 car and the owner has the matching numbers motor for it

[@benni727]

@@xacoupeguy that's allright them was gunna say its alot of work if it was only a 6cyl shell

[@paullang1961]

@@benni727 lol mate never to much work if thats what you want

[@georgecupac1202]

finally a real car on KZbin instead of the WOKE crap that passes for a car nowadays.