Xiaomi M365 Broken - No Power

[@LaamaCapital]

I had a similar issue and I was in contact with the import company. They said that it's sounds like a moisture issue and it wouldn't go under the warranty... So I opened the bottom plate, disconnected the power supply connection and all the other connections on the circuit board. At this point I could feel that the connection are wet, so i took my hair dryer and blew the connections for a couple of minutes. Plugged every thing back and the scooter came alive. No need for changing fuses or anything else. P.s. watch out for the bottom plates screws, they are really weak and will easily break if operating power tools. Good luck!

[@aarondempsey4086]

It worked on my scooter got abit water damaged took all the wires out used the hairdryer now it’s working perfectly 👏🏻

[@butterssfromthe3104]

What color was your battery pack light? Mine is a solid blue and the charger stays green

[@alemaassm]

Were you able to solve the problem? I'm having the same issue. I've already solded some tabs on the battery and it worked for a week. But now every time I connect the charger the scooter stops working and won't turn on again.

[@keanwalsh4292]

I’m having the same problem

[@alemaassm]

@@keanwalsh4292 It's the tabs on the battery! we fixed our scooter by solding the loose tabs, you can take it to a scooter shop or do it yourself

[@keanwalsh4292]

@@alemaassm the scooter is only brand new. Purchased a week ago. I’m new to it all. Hasn’t been used over long distances at all. However it turned off two days ago while I was out and hasn’t been working right the same. Any suggestions?

[@oneeyedrone4293]

A few steps 1. disconnect battery main plug (the black one) 2. Measure voltage and under-load, if its 20v no load, and goes to 3-4v with a little bulb or anything, then its a weak solder. 3. Using exacto knife examine all solder joints (they are on the bottom and top face of the battery as well). You will see they are weak if you press them. 4. Using 100W or larger soldering iron, re flow the solder on the battery. They rarely die but it does happen, its a battery issue regardless, the M365 is a tank so its not junk by any means.

[@cocopymes443]

Exactly

[@68pishta68]

Trouble​ :BMS flashes LED, but the scooter does not turn on.Solution​ :1. Check battery output voltage. If it is in the range of about 30 to 42 volts, it means that the BMS board and the battery pack are OK, and the problem should be looked for in the scooter controller.2. If the voltage at the output of the scooter is below 30 volts, pay attention at the blinking LED, it signalserrors that disable the discharge of the battery:a) a short flash once per second means at least one of the parallels of the battery is discharged below the level of the "Cell under voltage" parameter. It is important to understand why this happened. If the battery is completely discharged, and all the cells are evenly discharged to alow level - this is the normal mode of operation, there is nothing to worry about, you just need to connect the charger and charge the battery. But if only one parallel dropped down - this is a cause to look for broken contacts or a faulty cell.b) continuous light - means the protection against over current or short circuit protection has activated. In this case, you just have to wait 10-20 seconds.c) a long flash once a second - it means that the protection against temperature rise has activated. In this case, wait until the temperature drops.d) a short flash every half a second - this is normal mode, there are no errors disabling the discharge of the battery. If the LED blinks like this, but there is no voltage at the BMS output, it means the board malfunction, please contact the technical support

[@bigglestheflyboy]

This is not much good. Remember the guy said he has no idea what he is doing, so he's not going to have any idea what all this means.

[@paulnaquin]

Why my battery is blinking but unfortunately no have power connection pls help

[@sameulahmed4026]

This happens to me but when I charge it works but when I ride after 5 min of riding it switches of completely idk what to do

[@Tony-mr1yh]

Found any solutions?

[@miladarabi7736]

Exactly I have same problem, I changed the top control kit but didn't sort out and still is faulty

[@Zilli_341]

Try disconnect the battery and the power supply, hold down the power button for about one minute. Reconnect the battery and power supply and try to turn it on. (Translated with google translator)

[@aleksanderholm2428]

What does this do?

[@Zilli_341]

@@aleksanderholm2428 Great question, I have no idea lol. It probably did something useful if I went out of my way to write it 6 years ago. Usually you do something like that to reset the electronics, you wait after unplugging it for the residual charge in the capacitor to dissipate, I'm guessing it's the same thing here.

[@paulbain8333]

hi why would my front wheel just judder as if its trying to move i thought it was the front wheel so i bought a new one and its still doing the same any help would be appreciated

[@dziekan_tek]

Check voltages in this 4-pin connector in the mainboard (black-yellow-green-red): * black to red about 5 V * black to green about 36...42 V (depends on the charging level). The same should be on the board inside the steering wheel (you can lift up gently using flat screwdriver - it's glued by the doublesided adhesive tape).

[@jacobkofoed6109]

Were you able to fix it? Can you give us an update?

[@kashifahmad9926]

Did you manage to?

[@giannisimmons8942]

@@kashifahmad9926have u ?

[@Cannacoennos]

No problems so far,am still in love,hope your problem get solved !

[@bobthbuilder1311]

Red light means its charging it turns solid green when it's charged.

[@smoxesss]

Sk what you saying is if in charge won't light up??

[@connormclean4220]

Yea mine does that it says it charging and charges but it don’t turn on

[@CaaZ_]

I have the same problem on my Pro version, it will not power on, and the battery is full charged, im confused what the problem is and how im going to fix it self??

[@3LGang2L]

Did u end up fixing it bro mine has the same problem but mine stopped while I was riding and the front wheel locked up

[@awab1597]

@@3LGang2Ldid you fix it?

[@BonesAyles-kj7di]

My tx 85 pro scooter won't turn on at all put a muliter meter on the battery and it reads 18.6 does that mean I need a new battery please help

[@HgielyakHgielyak]

Mine is turing on blue flashing like on battery after changing bms....but got soild red on the box opposite? ....lcd display turns on but no power

[@ianl4308]

this is the same as the one im attempting to fix here ,i will let you know what i find out today

[@HgielyakHgielyak]

I changed the bsm and that control board with the wires that go to it...still no power to front... Mine turns on links to the scooter app but still has a red LED on.. whilst now the battery has a continuous blue flashing LED which it never had before it was red.im.fuming as it's not old at all but thank u for getting back to me 🤝🏻

[@HgielyakHgielyak]

​@@ianl4308hi did u manage to solve the problem

[@kevinsong712]

This is a big flaw for the scooter. The scooter has an energy recovery system that charges the batteries when you coast or use the brakes and it will damage the batteries when you do so at 100% or with an almost fully charged battery. My xiaomi scooter did not arrive yet so I do not know anything about fixing it. I heard that you will blow a fuse of some sort and you may get that repaired or buy a new battery pack. I guess you should let the motor free spin and get some power out before you set off.

[@kevinsong712]

Heard there is a reset button of some sort on the upper right of the pack. Try holding it a few seconds in.

[@kevinsong712]

It should be under the massive black sticker

[@jorgenv]

I think this was fixed with a firmware update.

[@cesardiaz1661]

friskus thanks for the suggestion I will have to look into it.

[@TRYtoHELPyou]

seems to me the scooter is bluetooth locked? is that possible?

[@CaaZ_]

I have the same problem, the charger turns red light, but i can’t screw up the all screws🙁👎🏻, i hope i can fix that?

[@mastaofthemetavrse976]

Have Eva tried recycling it ?

[@tezcatlipocao.o754]

i have a powerocks s1 and i didn't used / charged my scooter for 5 months and now it doesn't charge at all... i sent email to powerocks and no answer.... i managed to get one on phone and he said problem with charger.... i checked the charger and it charges 24 v as written on it... help!!!! :(

[@darkvator8218]

My aovo pro looks totally different inside from yours but I am experiencing the same thing...the red-light on the charger indicates that it is charging, on your scooter... and the green light indicates that it is fully charge....my aovopro charges properly but for some reason will not cut on....I am also looking to fing the fuse box or to locate the fuses but cannot find it or has not seen anyone with a avopro with this problem so far

[@cans_of_horror]

i have same problem same scooter

[@badalgupta3360]

Take the 4 screws on the top near bars check the connector to the display it does manage to come off some times if not strip the display and check connecters

[@martingee6659]

Will it turn on without the speed control box?

[@rhettoracle9679]

I know zip about that scooter. Multimeter on on off switch. Then mosfet controller most likely problem areas. Good luck!

[@aquariys]

if you haven.t solved the prb check the cells..one of them is disconected..from bumps and vibration..it.s a common prb..

[@lewisadams3114]

How

[@EZFLX]

??

[@solimansaad-lennkh1105]

How do you reconnect them

[@djmurcs]

How do you check cells?, Where are they exactly? Cause my scooter did turn off permanently after going over a bump

[@porkpie8667]

no warranty ?

[@stephenthornton4251]

Have you checked the contact under the power button I had one that wouldn’t power on so I removed the metal plate and rubber button under it was a small metal contact disk I cleaned it and put it back together then it powered on

[@cobycoy869]

How do you access this

[@djmurcs]

I'd also like to know

[@telasdepierre]

Is this defect in the battery frequent? Why does the solder break? Thank you.

[@basuyarbrough5365]

I ordered one of these from Amazon (I live in Oakland ca) The UPS driver ended up stealing my package and then they ended up sending me one for free and now when I try to press it on I turn it on it flashes but then it turns right back red and off

[@Ali-mf6ge]

That’s ducking crazy

[@dan5pot]

what was the problem? why you don’t tell us ? thanks mate

[@metalejo]

it was a fuse in the battery

[@ΣτραβάκαιανάποδαΜ]

xiaomi M365 not turn on anymore blinking tail?

[@razzbozz3537]

My scooter do not cargerd and can't turn on. Can U Halp me???

[@zimberryberry1714]

I have the same issues with my own Eco Flying scooter I o ly just open it today that I'm commenting

[@jpthestoner2778]

I have had this problem today I actually tried flashing my scooter because I was told it would make it faster, I have the m365 lite model and it was all going fine it flashed and said stand by my scooter whilst uploading , then told me to reboot my scooter then ever since I have not been able to turn my scooter back on, however the tail light flashes red for a minute or so if u try turning the power button back on ? Can anyone help me please 🙏

[@faridmamesov7717]

Dude I did same thing now I can't turn it on did u ever fixed it?

[@LGDeezy619]

Reset the BMS on the scooter..... It works with any model that "stops working" or "won't turn back on" It's a safety mechanism for the battery. There's a little button Located on the motherboard you can see just after the lineup of batteries. You'll need the female (flat on one side, rounded on other) for the larger main power connector piece, so that your charger is connected directly to the battery. Look closely and you'll see a button on the motherboard, Poke a hole thru the plastic, press it.... You should see it begin to flash red and your charger should for the same. There's one on each of the main three types off batteries used by scooters.

[@doncodman913]

@@LGDeezy619 Hi . Any chance you could take a couple of pictures next time you are in there ? Could be very helpful. Rgds Don

[@gothampixel]

I'm dealing with a dead one as well, at first one of the tabs on the battery was loose so it would not charge. I used a wad of tape to add pressure to that connection once the battery cover was back on and it worked for a week or two. Then after a normal commute of 4 miles, I turned it off and now it won't turn back on. No power and it won't charge anymore.

[@gothampixel]

I was able to fix mine. Two of the leads / clips connecting the batteries detached. I had to cut away the clear plastic protection to find which ones were bad and then solder them back together.

[@fursure89]

@@gothampixel What did you use to to fix this?I have two connection spots that cracked right at the area where it bends over to go to the batteries and cannot find anyone to help me. Hope you see this, thank you so much! I do already have a soldering iron but am new to all this as well, but got the soldering concept down I believe just need to know how to fix those connections =/

[@elozorgoldschmidt4983]

I have exact same scenario

[@Cristallina83]

Hi everyone, I have received my scooter and it doesn't work at all since the beginning. I have never used it and it's brand new. It doesn't turn on in any way and the battery doesn't charge at all. The light on the charger remains green, it never turns red. I opened the bottom part and followed the instructions on this video and others I saw. When I plug in the wire to the battery, inside the battery I can see the red light flashing only 4 times. After 4 times it stops blinking. I saw the connections on the battery and they seemed well fused on it. No one is moving. What do you think it could be the problem? I thought about something about the battery that doesn't work properly. Can someone help me?

[@AidenAidens]

Return it yo. You shouldn't have to deal with that on a new scoot

[@abdulrahmannadzri9760]

i have the same issue. have you resolved it bro?

[@ndiggadee2663]

Same issue here as well

[@TKomoski]

@engenteur I just bought one on Ebay for $175 Cad and it has your same problem hope Y'all fix's help

[@fursure89]

@Christallina83 Did you ever get yours fixed? I saw this post you put on a m365 french english forum too and am also having the issue, but I think mine is a connection claspe issue that needs to be soldered, I just don't know where to find little tabs or whatever to re-establish the connection =[[ Hope to hear from ya soon, thanks! pray, create, and be the change for world peace y'all!

[@ManuelW]

On my M365 the Cable form the ON Switch to the Controller was broken, I replaced it and it works fine now

[@simonnaughton2272]

Where did you get a replacement cable?

[@ManuelW]

I've replaced it with a network cable and soldered it in ;)

[@wilberbarrera1429]

Manuel Wagner hi where did you find the control replacement I need one too

[@darkvator8218]

The firet time ive had a problem with my aovopro ive rode it for hours , all the way down till the red light start to blinking indicating that its about to die on me...after riding it all the way down till there is nothing left in it, I believe all scooters are program to shut off once it reaches its dead limit to protect it....but getting it to cut back is the real problem. I then charged it up fully, then open up the bottom to look inside ..played around with the wires while holding/turning the power button on off & it came back on to my surprise......the second time, i rode it all the way down till there was nothing left in it & the red light started blinking on me, it shut off on me this time and tap out when there was no juice left... But This time when i hit the power button to cut it back on or to see if it had any juice left in it... it didnt cut back on,, but it will charge doe....some say it could be the fuse, but i do not see any fuses or no where the fuse box is. Please help ......it will charge but will not cut on ,what could be the problem here???

[@scottsheppard1468]

Hello mate I have same problem with xiaomi mijia electric scooter I thinks buy new parts every thing on it's

[@lillyreid6498]

Mine moves a inch an then makes a rubble hellp

[@lillyreid6498]

Mine the same i asked every one hopyfully he helps

[@en2oh]

You might have a blown Hall effect sensor in the motor/@@lillyreid6498

[@billysanches2202]

I have the same problem. Tried to disconnect and reconnect everything but it doesn't work. Have you solve it?

[@Gokhan_AKSOY]

Billy Sanches ı have the same problem. did you find any solution.?

[@musclegang8255]

Mine it turns on when plugged in then turns off

[@86gormo]

Any luck with this have same problem

[@zoekennerson4327]

Hi did you ever find a solution?? I have the exact same problem??

[@GeekyStuff]

Hi Zoe. Not sure if you have seen my other video. I did fix it temporarily in the other video with replacing a fuse, but then the fuse blew again! This kept on happening, so I sold it eventually as not working 😞

[@storytellersleepless]

New battery circuits board or new motor control box is needed more than likely unless there broken cracks circuitconnection on bat ... simple fix... what u needed was a low voltage testing kit,to traces the current...

[@allanstrand638]

Reset button in front ogf battery closest to camera small round black (?)

[@tomc131]

Do you have any videos on the Zgemma H2H coming out soon?

[@GeekyStuff]

The Salah already have it mate! look at my videos section

[@tomc131]

Geeky Stuff I know about that mate. I'm on about if they're are any future videos on it?

[@GeekyStuff]

The Salah not sure. not much more to cover. I set it up and it works. what did you want know??

[@tomc131]

Geeky Stuff Can you put IPTV on it and use echannellizer like you did on the H2S?

[@GeekyStuff]

The Salah Hi mate, it would be exactly the same process.

[@LaurentLieben]

There is a reset button on the battery's BMS. try to push it.

[@roserazavi696]

where is it where is the reset button

[@UGISPRO]

Seems like it's could be battery error.

[@nikoserezoglou2190]

i had the same problem and i opened my motor controller and i saw that i burned a chip from the controller

[@fbi4227]

My E scooter says its full charged but when i use the scooter it does not turn on :(

[@Suwar-alzahab-1969]

same

[@znxx_proofy5768]

Same

[@AndrewMiller-c8b]

Now my front light comes on but hit power button nothing

[@SullyFaz]

I just bought my scooter and it wont turn on at all i charged it and it wont turn on help?

[@craigway7602]

I have the same issue have you managed to get it sorted?

[@MrTmac493]

If u just bought it, did you connect the wire inside the handlebars?

[@otleyshev68]

Hi hope you can get you scooter fixed ? How long you had it ? How much I was thinking about buying one but not sure now!! If you considered selling might be interested diy project thanks kevin

[@vinsenior5925]

your motherboard next to your battery underneath it should have a light that flashes and I didn't see a light

[@simondavidson3964]

My scooter doesn't turn on properly the led screen just flashes and doesn't turn back on, my scooter is a replica, can anyone help with this

[@paulbain8333]

could it be the throtle thats broken

[@marcusaurelius9123]

I had the same problem. I folded the scooter and held it upside down which fixed it at least temporarily. May have been a loose connection

[@dkballingout3914]

Bro your a god, I legit had it folded and it wasn’t working trying to fix it. But the I put it straight and it started working again

[@jeremiahl2552]

Probably means broken wire where u bend it at. Moving it causes it to reconnect for awhile.

[@sarahjanedurrant4382]

Keep all wires in xx red light means it needs a charge xx wait until light is green xx

[@pithikoulis]

How long did you use it before this happened? Keep us updated if you fix it.

[@GeekyStuff]

Manos Seferidis only used it about 4-5 times.

[@archie497]

Change the BMS COST £20-£40 ebay

[@vellythomas1640]

I don't have a power button for my scooter wat should I do

[@iss3127]

Same problem just occurred

[@Unknown70u]

I’ve got E 50 on my screen, anyone know how to fix it or what it means?

[@debbiebebington9803]

It's charging

[@UGISPRO]

Need to unplug everything as possible. Need to hold power button. If that's no helping need to disconect battery, to make sure no lights blinking at all. Set it up. Should work

[@skeelo69]

Before you unplug everything, make sure you take a picture of the wires connected so you know which ones connect with which when you plug them back again.

[@haxto1]

Hey Brainiac, the plugs are all different and none are interchangable, take a picture of this and study it.

[@5chiffi]

The red lights are normal... My Scooter works fine and is blinking also red inside and red on the charger

[@mastaofthemetavrse976]

BRO that blinkin lights violet 🤦‍♂️

[@hauikanamu9641]

Its a running start scooter. You need to spin the tire for throttle to work

[@justfilipps8644]

Am i the only one who seen this comm and wants to die

[@Dj2006]

@@justfilipps8644 nope

[@daveswatton4468]

❤

[@simondavidson3964]

My scooter doesn't turn on properly the led screen just flashes and doesn't turn back on, my scooter is a replica, can anyone help with this

[@free.palestine9296]

Yo mate I've got the same problem I soooooo gutted

[@free.palestine9296]

Did I find a solution I've looked everywhere people saying they cant fix it bcuz it's a coppy