Engine build part 8, installing the advance retard system and the points plate, getting the engine ready for the test run in a couple of weeks, setting the points will be a separate video and will come later.
Пікірлер: 26
@dannyv595711 ай бұрын
Your videos helped my build tremendously. Thank you from Danny V in San Diego California
@johncooper72425 жыл бұрын
sounded like there was a lot of Tourettes in the Benny Hill section when fitting those springs lol
@MrOkech4 жыл бұрын
Hi. Can u help me. Which cylinder is left. Vs right.do u tell from the seat or the front ?
@OldBiker4 жыл бұрын
From the seat
@zefallenmadonnavizzebigboo10175 жыл бұрын
Im upgrading my points and condenser on my royal enfield to boyer bransden electronic ignition do the points have to be on point before I change it?
@OldBiker5 жыл бұрын
Just follow the instruction sheet you get with the Boyer ignition, you cant really go wrong with those.
@zefallenmadonnavizzebigboo10175 жыл бұрын
well done Cliff, I thought I'd ask you cos you seem to know what your doing I only ask as I'm not sure it mentions this I'll re read the distructions lol. cheers fella, hope you and your fam have a merry little Christmas, Matt.
@murffff2 жыл бұрын
hello man what size bolts did you use for the points housing i know the are counter sunk i like the allen heads like you have used all the best murf
@OldBiker2 жыл бұрын
Hi Murf I think they are M6 x 12mm but will check tomorrow and let you know for sure
@murffff2 жыл бұрын
@@OldBiker that would be great kind regards murf
@OldBiker2 жыл бұрын
@@murffff Hi Murf yeah it was M6 X 12mm and uses a 4mm allen key, you can also get the stainless countersunk lock washers for it on evil bay too
@murffff2 жыл бұрын
@@OldBiker sweet thanks man this old xs650 of mine is fighting me but i will win
@MrOkech5 жыл бұрын
wish i was riding like y'all! can anyone help me. i ,ve spending my whole life just trying to set the points gap. is there a most bottom line.start from scratch position the plates should be, before i try to find the widest opening on the point.i just cant get the low volt test light to come on at the f mark. and isnt it supposed to go out after the f. my light stays on almost 3/4 of the way after. sorry for asking ,im getting burnt out
@OldBiker5 жыл бұрын
Next Sunday if I remember I will try to do a step by step guide on the points, I have a top end I can set up on the bench to play with so should be easy enough to do..
@hommystattoo50945 жыл бұрын
@@OldBiker I just got done installing my xs charge pma and my new boyer bransden ignition. I need too set up my tdc on my pma so I can adjust my timing. What's the best and easiest way. Top dead center tool that fit in the spark plug are useful but I have no idea what type I need.
@OldBiker5 жыл бұрын
@@hommystattoo5094 The tool that screws into the spark plug hole to find TDC is not very effective, due to the angle of the plug hole the slider in the tool just gets stuck when the piston comes up and hits it, now to quickly find TDC look at the camshaft ends, one has a pin at the points end and at the other end has a keyway, when they face directly up, you are at TDC, to fine tune it, put a pencil or the like in the plug hole and sway the crank back and forth a couple of inches each way until you find the sweet spot in the middle where the pencil does not move. That's how I done my one. If you want to try the TDC tool, it's a 14mm threaded size one you want.
@hommystattoo50945 жыл бұрын
@@OldBiker are you a member on xs650 forum?
@OldBiker5 жыл бұрын
@@hommystattoo5094 Yeah been on there a while as IllusiveJack
@randallridnour89544 жыл бұрын
Do you live near Heathrow brother?
@OldBiker4 жыл бұрын
Stevenage, 30 miles north of London
@randallridnour89544 жыл бұрын
@@OldBiker So there must be a major airport there l guess.
@jarnomeekes67562 жыл бұрын
My engine didnt have these in when i took it apart, yet it ran fine... How tf is that possible?
@OldBiker2 жыл бұрын
Hi Jamo Later models had electronic ignition built into the stator
@jarnomeekes67562 жыл бұрын
@@OldBiker ah alright, thanks! So to set the timing i only have to properly do the valves and make sure the camshaft aligns with the crankshaft right?