XTOOL D1 Pro In-Depth Setup Guide, Assembly, Creative Space Software Fundamentals and Fume Extractor

[@EmbraceMaking]

If you appreciate my in depth and detailed videos, you can support my efforts with the links below to the best xTool prices! Other material links in the video description. XTOOL D1 Pro 10W: ► www.xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting?ref=D5HpJRsyqyUUnt& XTOOL D1 Pro 20W: ► www.xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting-b?ref=D5HpJRsyqyUUnt& XTOOL D1 Pro 40W: ► www.xtool.com/products/40w-laser-module-for-d1-pro?ref=D5HpJRsyqyUUnt&

[@badboyboydc6779]

You are the first person to post what xTOOL doesn't tell anyone. Bless you.

[@EmbraceMaking]

Thank you!

[@llkaygifts]

I was afraid of opening my xTool 10w, but when I watch this video, everything became clear. I put my machine together by watching this video; stopping and starting with each section. I have purchased the fume extractor and the power button. Now I am and ordering the the filter to use with my 3gal shop vac. I am so appreciative of your video. Your tutorial is beyond my expectations and the best video for putting thing together by far. Subscriber for life!

[@llkaygifts]

BTW thank you for grate piece for the board and connectors

[@EmbraceMaking]

Thank you so much for your kind words and I'm glad the video was that helpful :)

[@SFCSMOKER]

Those dad-blasted red, white and yellow cables took me longer to connect than the rest of the assembly! I thank you sir for your video as it helped tremendously! A heart surgeon would have had a time with connecting those cables

[@EmbraceMaking]

Glad you got it sorted out and the video was helpful!

[@flalife904]

Lmfao me to my fingers are to big legit took me a while , they didn't go in easy and when they did I was afraid a pin was bent or broken

[@richsoutherland2924]

Haha yup. Exactly my most frustrating part!

[@stopngo10]

I was came to the comments looking for exactly this! I don’t understand what they were thinking when they decided to put the connectors there. Who can even fit their fingers in that space to connect those 3! Especially the white one took me forever. Had to use the screw driver and hope I didn’t mess anything up. Literally almost quit the entire assembly because of those cables.

[@markg8972]

Haha ,yes my friend I feel you I have just looked for a video to see if there was an easy way there so delicate and in such an tricky place😂

[@timothywhite6386]

Today is day one for me with my D-1 after having spent yesterday putting it together. There were things i did not realize about cables etc.that were not explained in the drawings, and I learned a lot from this video. Thank You for putting this together. I have watched many other video's but this one explained things for a true 'Beginner' (I am technology challenged as well) and for that I appreciate your time and the time explaining things along the way.

[@EmbraceMaking]

Thanks Timothy glad it could help you out! Thanks for the comment as well!

[@havocproltd]

"...kerf only has four letters..." and now I'm blowing martini out my nose! SIR! This is hands-down THE BEST tutorial I have ever seen on anything! You will see my order for the fume extractor momentarily. THANK YOU! Take extra desserts for the rest of the year!

[@havocproltd]

I don't think XTool could have chosen a better rep for this!

[@EmbraceMaking]

Ha thanks for the kind words! Glad you really liked the video and my sense of humor :)

[@llkaygifts]

Agreed!!!

[@jo-nellisenhour3495]

I can't tell you "thank you" enough! I watched your video about 3 times, and then while I was putting it together I would just pause your video. Got it set up and working on the first try!!!

[@EmbraceMaking]

You're very welcome, this is why I make these videos :)

[@queencityteashop]

I'm totally new to Xtool. I looked at a dozen videos. You're awesome. Your video is better than the actual manufacturer!!!!

[@EmbraceMaking]

Wow, thanks! Really appreciate the kind words :)

[@judithholland9592]

My gosh.. glad I found this tutorial. Saved me a lot of "anger" time with this machine. I just put it together and made sure the cable management was smooth once completed. Thanks a million. I really appreciate you.

[@EmbraceMaking]

Glad it helped! You're very welcome!

[@robotron07]

CABLE MANAGEMENT IN THIS MACHINE IS AN ABSOLUTE NIGHTMARE

[@alieandtheAngels]

Just about to go and pick up my new D-1 Pro 20w with extender and you have made the thought of set up far less daunting!!! Thank you so much for your fantastic guide... people like you make this World a better place to be in and we Thank You for your time and efforts - they are greatly appreciated (even here in little old New Zealand!), wanted you to know - even if you aren't always told so xxx

[@EmbraceMaking]

Thank you so much for those kind words! Glad it can be of use to you and others :)

[@rrdavis55]

Im installing the extender now. 4-04-23. Going to use the drag chain on top of the rail. Ive been in electronics for 55 years and must admit I needed this video and found my big body inside the laser frame while it was on a bed and up on its side! Stay tuned for "Page Two" as Paul Havery would say!🤣

[@1824511]

I am new to the Xtool community having just bought the Xtool D1 Pro 20W and I am in the process of setting it all up. I do like your explanation and demonstration of how to manage the cords with the better placement vs Xtools utilization. As far as the fume extractor I really like the concept but there is no explanation as to what you are connecting the CPAP hose to and how that works. I think better explanation of that would be helpful! This makes individuals do further research when it could have been done with one person being 100% concise with all the modifications being done. Otherwise a very good video with great information to help make production better for everyone. I will definitely be watching more of your video's.

[@EmbraceMaking]

Thanks for the comment! Yes I am sort of kicking myself in hind sight that I wasn't more clear about that in this video. However, for your reference here are two videos that explain the other end of the CPAP hose: Filter system: kzbin.info/www/bejne/oWjUhXhqqZmmnJo Filter system with an enclosure: kzbin.info/www/bejne/jKamoJ9jjdtmqKs Similar system on the Creality Falcon 2 with the vacuum system explained: kzbin.info/www/bejne/jXTFppufesefpNE

[@KarlBunker]

Before I got a honeycomb bed for my laser, I used a silicone dish drying mat. These mats have raised ribs, so they give you an air gap underneath your work piece. I don't know if you can find one big enough to cover the work area of a D1, but most jobs are smaller than that. I love the idea of your fume extractor!

[@EmbraceMaking]

Nice idea on the dish mat, and thank you!

[@Stock_Skills99]

Huge help!!!...I had to walk away for a day because I couldn't get the Y-axis aligned. Super Easy fix that my frustration wasn't allowing me to see. Thank you for taking the time to put this video together.

[@EmbraceMaking]

You're welcome Neal, hope you come back for more of my XTOOL videos!

[@douglasscotto5936]

Really appreciate the detailed video with extras! I assembled mine about 80% of the way via the manual and then took a break to research further, finding your video during this time. The details with regards to the cable routing were amazing and I am nearly done with all of that in my setup. Thank you!

[@loribrooks6736]

Wow! Super helpful video (yes, even 1 year later). I just received my Xtool D1 Pro and will be assembling today. Your video is a game changer. Thank you!

[@EmbraceMaking]

Glad it was helpful! Doesn't seem like anything in the assembly has changed in the past year so should be still relevant :)

[@midnightng]

I fully expected to see 1 million+ subs for this channel. Outstanding video, thank you!

[@EmbraceMaking]

Wow, thanks! Hope you're right!!!

[@hulabird]

As totally careful as I was to follow every single instruction they gave to the letter, I missed that connector at 6:56. I hadn't fired up the machine yet because I'm waiting for a couple more incidentals and while I do, I saw this video! When I watched this I went back and redid everything and I'm still working on it now going through second by second of this video. My belts weren't tightened properly, I just randomly attached the gantry somewhere in the middle instead of bottoming out at the back. THEN tightening the connector bolt screws. I felt like the instructions might have assumed end user knowledge being much greater than mine is. But this connector tucked in at 6:56 would have had me shipping the machine back 😭. Onward with new knowledge!!! Appreciate you!

[@EmbraceMaking]

Thanks Debi! Glad my video could be of use to you, enjoy your machine!

[@jeffthomas7383]

Excellent video! Great tips on cable management, gantry and stepper motor shaft alignment. xTool needs to either have that little tab cut off the circuit board which prevents it from aligning with the other side or revise their assembly instructions the way you did it. Also love the flame extractor. Will be purchasing one tof those from you for sure. Much more elegant solution than one of the rinky dink enclosures... Thanks for all your thought and work on this video. Best xTool D1 Pro video I've seen so far.

[@EmbraceMaking]

Hi Jeff, that's a lot of praise! Thanks for the thoughtful comment, really appreciate it! Whenever you're ready to get a fume extractor nozzle you know where to find me. Thanks again!

[@danieller9645]

Thank you Very Much!!! While we watched your video to set up my D1 Pro XTool, my husband put it together while I "manned" the space bar for your video. hee hee You made this easier than the user manual, especially including the extra little details. We appreciate you and will be liking and following for future references. :)

[@EmbraceMaking]

Thank you so much for the comment, really happy you found the video so useful :)

[@RonMarshallrone]

Thank you Brother....this is one of the best most thorough setup vids I've seen and went through and I've been woodworking all my life and running a business for the last 6 years and run a CNC so I'm used to watching vids like this but yours was awesome. I didn't even need the manual and i was up and running and already doing orders I have within 2 hours. This is what the manufacturer videos should be like...some are good but most not. Great job man..very impressed. And I will be buying your fume extractor. My whole house smells like char lol.

[@EmbraceMaking]

Thank you so much for the kind words and high praise! Put a lot of effort into this video, glad it is helping people get going!

[@jennifercontreras3181]

Today I conquered putting the d1pro 10w thanks to you. The manual was good but you explained and showed me exactly what I needed to do. I appreciate you!

[@EmbraceMaking]

Glad it helped, this is why I do this!

[@FernandoMartinez-ih6rp]

Today my D1 pro Golden Red arrived and I had never seen a video about this, and thanks it was very useful as you explain it, you really speak very clearly ,you have a new subscriber 😊

[@EmbraceMaking]

Glad it helped! Thank you so much for subscribing :) I have lots of D1 videos if you check the rest of my channel

[@GregR333]

Great information and well presented! The only things I'd add are: - when you and initially putting together the pieces, insert the screws and tighten them only until they just more that touch. When all the fasteners for a part are in then go back and tighten them in a couple of rounds. Tightening them at the start could cause mis-alignment. - do the zap tie around the x stepper first then secure the cables under the side frame but be sure to have the x axis all the way to the back and secure cables starting at the back and work towards the front.

[@joepro8401]

Cheers for the tips on the cable ties! Was having issues with the wire moving excessively, but your tip fixed it

[@BarbaraMulvey-w2h]

I can't tell you how much you have helped me with your videos! I cant wait to receive your items that I've purchased!

[@EmbraceMaking]

Incredible, thank you ! Hope you enjoy them!

[@fknowles11]

Clear instructions and good camera work ensures that this video is concise and effective, well done and keep up the good work

[@EmbraceMaking]

Thank you so much Frank, always trying to improve and make the best content I can. :)

[@jamoreno1982]

Thanks for this very thorough and complete video. After reading the horror stories on the FB community from some folks struggling with their set up and output of their projects using the D1, I realize how lucky I am I found your channel and this video. Really great stuff and thanks for the practical and comprehensive way you share information.

[@EmbraceMaking]

Glad it was helpful! I wasn't aware so many people were struggling on the FB community. I think it's one of those things where there is the initial learning curve and once you break through that it shouldn't be too bad :)

[@shelexie5323]

I would never have made it through the setup without this video! Thank you!

[@EmbraceMaking]

Glad I could help!

[@christinebagatin5945]

Hi there, video helped a LOT!!! Trying to figure out how to adjust the rear plate, as the focal point is not longer at (0).

[@KristianaW]

Thanks heap for doing this video! I HATE reading instructions so having this video made my life so much easier when I had to put my D1 pro together a couple days ago. 🤗🤗🤗

[@EmbraceMaking]

No problem, glad you found it helpful! If you also have the RA2 rotary attachment I just released that video and it is pretty thorough as well. Might also be something you want to check out :)

[@PhoenixCustomsWoodworking]

you mention using a protective mat under your project, Xtool has their iron honeycomb workspace, as for your burning on the back of the piece and having more crisp front, the air assist should help with that

[@EmbraceMaking]

Definitely! In a future video I have a lower cost solution to the honeycomb work space for people on a little more of a budget. The silicone mat underneath is a good pairing with this solution I will be releasing soon. Air assist definitely helps with the top surface and having air space under the part prevents all of the burning on the bottom side.

[@AnIrishExport]

This video may just have saved my sanity !!! I assembled my D1 Pro last night, and only got a chance to test it out today, I loaded an image into XCS to attempt to test run the machine, it wouldnt move after clicking on 'FRAME' , I chose to bypass that and attempt to engrave anyway, the module would only move along the X axis and would then constantly give me limit alarms.... I think this video has solved my problem, I completley missed that small black cable that plugs into the limiter for the X & Y axis... I dont recall seeing that in the assembly manual for some reason....

[@Oak_So_Pretty]

Absolutely brilliant. So glad I found this video. I just ordered the 20w d1 pro yesterday and this has filled me with confidence. Going to watch a few more times before setting mine up. Thank you for the content. Will be picking up the cover for the PCB soon. Very well done indeed. Subscribed!

[@EmbraceMaking]

Great to hear! Thank you so much for your support and for subscribing!

[@e46_nole]

So how did it go for you? Setting mine up tonight!

[@rickparent429]

Awesome video. We just received our D1 Pro today and this helped immensely. Keep up the good work!!

[@EmbraceMaking]

Glad it helped! Thanks so much for posting!

[@jeffdevries3282]

Great Video. Just used it to set up my laser. Now to start lasering some objects. Brand new to lasering glad I watched your vudeo. Thanks for all the tips.

[@EmbraceMaking]

Glad it was helpful! Hope you come back for more future XTOOL videos!

[@ChadsCustomCreations]

Love that vacuum adapter you made super smart and cool design.

[@EmbraceMaking]

Thanks! I see you have some experience with the D1 yourself, nice videos!

[@jenmatt5512]

Thanks so much for your thoughtful assembly steps! This new venture is scary enough without the concerns of messing up installation.

[@EmbraceMaking]

Thank you Jen! Glad it helped you :)

[@teresa6775]

THE BEST video out there with this detailed instruction. Thank you !!

[@EmbraceMaking]

You're very welcome!

[@vinnyeye]

Thank you! I didn't even use the manual. Your walkthrough and explanation was great!

[@EmbraceMaking]

You're welcome! More XTOOL content to come :)

[@dalebernstein107]

How often would the filter need to be replaced... can it be cleaned... with a blower, smoke and debris just goes out the window. But I like the idea of your fume extractor, more or less self contained. The area where I will install a xTool D1 Pro would require a fairly long hose, cutting down on the effective cfm. With a rolling cart and the vac installed within the cart, I suspect your fume extractor may be the way to go, depending on the cost of and how often the replacement, etc... of the filter would be. The shop also has a ceiling mount air filter... I know a Blower would rid all smoke.... and hope the fume extractor set would also. Thanks.

[@timkydde]

This video really helped with my assembly. I was having trouble with the cables and your tip/mod solved my problem. Thank you!

[@EmbraceMaking]

Glad you found it useful!

[@DarkMoonEmporium]

Thank you! This helped me so much, especially the tips on cable management. I was on the point of getting a drag chain to try and get the cables under control - your solution saved me some money!

[@EmbraceMaking]

Glad it helped!

[@jmo2400]

Very good, informative presentation....I have subscribed. My D1 20 pro will be delivered in a few days.....can't wait. Thanks again!

[@kidcompany]

Great vid. Just got my xTool D1 Pro 20W and your vid got me up and running quickly. Thanks!

[@EmbraceMaking]

Glad it helped Dennis!

[@Utaheyelid]

Just cut my first project and your video was such a help. Subbed and thumbs up. I got the air assist and the fume extractor and cut on a honeycomb tray and had zero char on either side. I couldn’t believe how clean it cut.

[@EmbraceMaking]

Fantastic! Glad you got it all sorted out and great results!

[@edhiestand1197]

@@EmbraceMaking What is powering the fume extractor? Would be interested in seeing what the exit looks like, window , wall or???

[@nessasmith9166]

Very Very helpful in getting my new laser up and running and helping me understand the basics. Thank you!

[@EmbraceMaking]

You're very welcome!

[@Djwhynotlove]

I love everything about your channel. The way you explain it, it’s super easy to follow

[@EmbraceMaking]

Thank you so much Aaron

[@laurac4562]

the wire on the gantry that was tucked up in with other wires was not plugged up. saw that in your video and said I do not remember doing that one. thanks again

[@EmbraceMaking]

Glad you got it sorted out! Would have been a shame to have not gotten to use it. Enjoy!

[@AmateurRedneckWorkshop]

I ordered the smoke extracting stuff from your channel and it is supposed to be here by Friday. The thing I am concerned with is that I have not been able to move the laser with light burn or laser box. I am going to try the users forum. The xtool folks set off my virus scanner every time I try to fool around with their website. Thanks for the video keep on keeping on.

[@EmbraceMaking]

Thanks for your order! So you are not able to frame or jog the axis at all with lightburn? Have you tried Lasergrbl just as a sanity check to see if its the software?

[@AmateurRedneckWorkshop]

@@EmbraceMaking it is not the hardware I left out a driver. It works with the xtool creative software right off.

[@VonKempDesigns]

This video was super informative and all around awesome, thank you for putting it together!

[@EmbraceMaking]

Thank you! Really happy you found it useful!

[@robotron07]

CABLE MANAGEMENT IN THIS MACHINE IS AN ABSOLUTE NIGHTMARE

[@EmbraceMaking]

That is where I tried to focus some effort on getting it under control

[@robotron07]

@@EmbraceMaking yes it was helpful

[@paskali79]

I just ziptied it to the bottom of the structure and had no problem.. not sure why y-all tripping, it's actually better than on most gantries

[@marklengal9990]

I wanted to add,Very well spoken also. XTool should be using you as there US representative. Sometimes I have a hard time understanding there videos due to the language barrier.

[@EmbraceMaking]

Thank you so much Mark, unfortunately that is a common challenge when dealing with overseas companies.

[@clydeschuyler]

Wonderful video! I just received mine today and used your video for the set up. The only difference I seen was they are using hex head screws now. All of the other set up info and extra tips are wonderful.

[@EmbraceMaking]

Awesome glad it was helpful!

[@timothyduzenski1386]

Tip for the tutorial: watch the assembly portion all the way through because you can conserve your zip ties. Or you can go get extra zip ties before you start assembling so you can execute his assembly tips, which are good.

[@EmbraceMaking]

Thanks Timothy, yes you will definitely need a few extra zip ties for this assembly!

[@timothyduzenski1386]

@@EmbraceMaking thank you my friend. At Home Depot the little do-dads are called mounting bases. The ones I got are 1“ x 1“ so I just cut down two parallel sides with a tin snips to fit the X tool rail. And you actually get a little bit more adhesion power. This wasn’t planned it just happened that way. Lol

[@DWIT3D]

Best assembly video yet. Thank you.

[@EmbraceMaking]

Glad you enjoyed it!

[@e46_nole]

THANK YOU for this video and your content! Just received my D1 Pro 20W today and like others, this has instilled confidence within me lol

[@EmbraceMaking]

Great to hear! Hope you've been having fun with it already

[@dmann579]

Thank you so much for your great content! I'm getting my XTool D1 Pro (10W) in a few days and am excited to make the modifications you described. Keep up the good work!

[@EmbraceMaking]

Have fun with it and thanks for the comment!

[@emilpopelka9001]

Should be getting my 10w red next week. New to laser engraving but not to making things with other tools, especially intricate stuff with the scrollsaw.Trying to make the setup and start up as smooth as possible. Great video, definitely will help, thanks.

[@EmbraceMaking]

Thanks Emil! If you haven't already ordered your 10W I would super appreciate if you used my affiliate link in the video description. Thanks!

[@Jackson10711]

Thank you, I've never used an engraver machine and since my hands shake more I need one. I've watched several videos and now I just need to decide which D1, D1Pro 10W or 20W to get. Thank you Also, I love and need the extra filtration you created

[@EmbraceMaking]

Glad it was helpful! Thank you so much for your kind words!

[@adamcolville2057]

Awesome video will defo help when I eventually get round to building my D1 pro 20w

[@EmbraceMaking]

Great to hear!

[@BrainwavesofHope]

hello and thanks so much for this video it helped me set up my xtool d1 pro. Now im at the phase of experimenting materials but I have questions for you before I begin: 1.Do I need both an air assist and your fume extractor? Do they do the same thing? 2. Do you suggest the metal plate or a honeycomb Laser Bed to go on top of silicon mat but under material? 3. Should the laser slide all the way to the mat or be adjusted where when it slides in, the back metal piece of laser underneath plug is even with the bracket its attaching to? Ultimately resulting in laser being approximately a quarter inch from the mat?

[@monicarader4257]

Very informative! I will be getting the adapter , the link to the hose doesn't work, is there a newer version??

[@EmbraceMaking]

Thanks Monica, yes amazon is temporarily out of stock it seems. I don't see a newer version in the meantime so you might have to shop off of amazon for that in the meantime!

[@mellissaerb8819]

Great video! wondering if you can use the fume extraction and air assist at the same time?

[@EmbraceMaking]

Yes you can, but the air assist might push some of the fumes away. The nozzle should still get most of it, but realistically never 100%

[@Pauuanthakali]

better of the informative videos on assembly of xtool d1 pro.. subscribed.. had similar realizations with gantry wires issues.. ill have to readjust carriages alignment as presented as i've noticed deviations in coordinates while moving laser head to 100x100 mm for origin.. seems 0x0 absolute origin keeps moving a mm off every return.. reason "free framing" works w/o precise positioning.. the fume extractor is brilliant! commend the ingenuity.. do recommend using air assist for wood cuts as it improves vastly cleaner kerfs from charring.. multiple passes at faster speeds vs few at slower rate works well with 5mm plywood for me.. excellent altogether.. thanks for sharing insight...

[@EmbraceMaking]

Thank you so much for the thoughtful comment! More D1 Pro content to come soon!

[@mrs.t6813]

I'm finding this extraordinary helpful. Question. There appears to be a cover over the air assist hole. Does that just peel off??

[@EmbraceMaking]

Thank you! Is it that white plug on the air assist inlet that you're referring to?

[@Moe_Z_]

Ive treid so many videos and this was super helpful and easy

[@EmbraceMaking]

Glad it helped!

[@MeganMaestas]

First, I'd like to thank you for putting together such a thorough and descriptive video. I have a question regarding the fume extractor that you designed for the 10W machine...we purchased the Air Assist tool with our new machine. Would we also need a fume extractor, or will the Air Assist serve the same purpose that the fume extractor served in this video? Thank you for any insight, we are new to the xTool community.

[@EmbraceMaking]

You're welcome! The air assist will blow the fumes and smoke outwards. It is designed to clear the space around the laser beam so it doesn't get diffused through the smoke and thereby increases the laser efficiency (or at least makes it stable). However the smoke will still get blown out everywhere into your room. The fume extractor is designed to try and pick up some of that smoke and then get it filtered or get it out of your room so it doesn't accumulate. With just the fume extractor is sort of has the same effect as the air assist - it will draw away some of the smoke from the laser path... however it's not its primary function. The primary function is to minimize smoke accumulation in your room. Whereas the air assist is generally aimed right in the laser path and doesn't do anything for smoke accumulation in your room. So each have their own primary function that is different from one another. If you use both together... it kind of depends on how strong your air assist is. It could blow some of the smoke and fumes outside of the reach of the fume extractor and that is just the reality of having one thing blowing while another is sucking all while the laser module is moving around everywhere.

[@lvhotglass]

Thanks for the great videos. You have really helped me assemble the d1 pro.

[@EmbraceMaking]

Glad to help!

[@RobertStinnett]

Thanks for the in-depth and straight forward video - much appreciated!

[@EmbraceMaking]

Thank you for the comment Robert!

[@sandydeacon1985]

Can you post the link to the adhesive clips you added to place the wire under?

[@EmbraceMaking]

In the video description :) but here as well: amzn.to/3W2WLZ4

[@queenofsheba357]

Thanks sooooo much! This video is MUCH better than the one that xTool has

[@EmbraceMaking]

Glad you think so! I really appreciate the positive feedback

[@danpersson9205]

Thanks for nice and informative video. Did watch this a couple of times, most needed was those parts regarding routing. (still have a little problem with the last fix (~13-14 minutes). Will check yout other videos coming days. Thanks /Dan from Sweden

[@EmbraceMaking]

Glad you enjoyed it, the RA2 video is being worked on, should be posted hopefully in a week!

[@RichardAnfuso]

Thank you, This video answered a lot of questions for me.

[@EmbraceMaking]

Glad it was helpful!

[@Gtrlac43]

Great video! Thank you for the cable management ideas. I assembled before watching this so I dealt with this problem also; although not as elegantly as you. Cheers!

[@EmbraceMaking]

Thanks Ron, glad you got it sorted out one way or another!

[@jacobartuso4450]

Where is your video on the attachment I have been having issues with the roller/chuck

[@EmbraceMaking]

It's coming! Got a little side tracked lately but I'll have one!

[@eduardodiasnunes941]

Hi! I have a 100W CO2 laser cutting machine that suits my needs very well. What I basically need to know is two pieces of information that I haven't found in any demo yet. Diode laser operational lifetime. How many hours do I work? The second question is: in a single pass do I actually cut how many mm of wood and at what power x time?. My problem with CO2 is that it takes up a lot of space and is also very heavy. This causes me trouble. Thanks.

[@EmbraceMaking]

The Xtool website says the laser head should last 10,000 hours... support.xtool.com/hc/en-us/articles/4405624562199-Pre-sales-knowledge-for-xTool-D1 In terms of settings for the wood I think it depends on a few factors like the color and density. In this video I was using basswood which doesn't seem very dense but it is light colored so I imagine it won't absorb the laser as good as something darker. I used the Creative Space preset which was 100% power @ 3mm/s speed. I was able to increase that to 4mm/s and it still cut fine. I experimented at 5mm/s and there were areas it didn't go all of the way through. I see ads online for this machine saying it will cut through 10mm wood but it does not specify if that is a single pass or what kind of wood.... realistically I think it would do 6mm thick in one pass at a very slow setting. I have a K40 here and I also find it heavy and cumbersome, plus the closed frame limits what I can put inside. The nice thing about these light, open frame lasers is that you can put the entire machine on top of a big workpiece if you had to. Will it replace the power and grunt of your 100W? Certainly not. The speed will be slower too, but it does have its advantages. Different tool for different jobs I guess.

[@livelandings747]

With cutting wood do you find it accurate? If for example I wanted to build intricate boxes do the joins fit well or is there large kerbs? Thanks for the video

[@mikek2824]

Can I just buy the stl? And make it my self

[@kabokreations]

wondering if you can help me...I'm trying to cut out the word love. when the machine is framing, it just frames a straight line, top to bottom. what am I doing wrong?

[@EmbraceMaking]

Hi Patti, I'm going to assume you are using the creative space software?

[@teque-awanderer1341]

Clear and concise instructions. You helped so much! Thank you!

[@EmbraceMaking]

Glad it helped!

[@KalOSRS]

It seems the newer updates to the XCS changed the interface a bit. I press "start" to start processing, and then tells me to press the button on the machine. When I do though, i get the "task canceled" message. Any ideas?

[@EmbraceMaking]

Are you running the latest firmware on the D1 pro? If not, maybe there is some kind of compatibility issue between the Creative space version you're running and the machine firmware

[@laurac4562]

thank you for the help and the video. machine is now connected and working

[@EmbraceMaking]

Great! Not sure how much help I could have been, but I'm happy to hear you got it working. If you have a minute to explain how you fixed it perhaps someone will come across this in the future and it might help them too. Thanks!

[@minimism]

Thanks for this video - just got a 10W D1 Pro myself and the fume extractor looks great; One question: What sort of volume of air do you think the extraction pump needs to pull (i.e. how many litres/min) in order to be effective??

[@ZDashGames-qz7xc]

Is there an stl file for the fume extractor

[@Jfbegood2yourself]

This is a really insightful and well thought out video. I have a question. I was having a hard time finding a work table for this laser and honestly I didn't want to take the time to make one. I have a Costco 34-in by 34-in card table. Should I get a piece of 26x26 in wood to place underneath the laser or should I just flash the table with aluminum? I use to laser engrave back in the day before it was cool and the machine that I used had a metal bed.

[@brianblather]

Can we get a more detailed or close-up view of how effective the extractor is? Also, I noticed that this mod only goes up to the 20w: 40w coming soon? I'd love to get this as it would save time and money on building or buying an enclosure. Definitely getting that rotary mod, though!

[@Silverstudiobc]

Should I use the vacuum extraction you recommend with air assist?

[@mrfurrutia]

I'm having problems when trying to home the machine, it will successfully home on the X axis but when moving to the back it will not reach the little end stop bracket and will just grind the belt... Could it be because the dumb wiring management? I'm going to redo it tomorrow after work but I want to be ready just in case that there is something else to check...

[@rickmorgan8912]

Can you still use air assist with your extraction nozzle installed? Thank you!

[@EmbraceMaking]

Shouldn't be an issue although depending on the strength of your air assist it *might* blow some of the smoke away from the nozzle.

[@its4michael]

Nice smoke extractor. Will it work with air assist on? Seems like air assist will push smoke beyond the extractors effective area.

[@EmbraceMaking]

Absolutely possible. I have pointed this out to a few people who have messaged me about it. I haven't personally tested it but it would make sense that air assist could push away fumes for sure

[@kandiecandelaria3134]

Just put mine together have not even turned it on yet. Question it said I could not use laser box basic? I don’t know what that is. Would my next step be down loading the free program from xTool? Great video go to go back and fix a few things you pointed out. Thks for sharing!

[@EmbraceMaking]

Hey sorry I must have missed your comment, I haven't used laser box basic. What kinds of things will you mainly be doing? For general use the xtool software isn't bad. If you're an advanced used light burn seems to be the choice of the pros

[@kandiecandelaria3134]

@@EmbraceMaking just want to be able to put clients name on cutting boards for now

[@TBR_LLC]

How do you get the gantry to move freely like that when its on? Im using lightburn, is that why mine isn’t free to move?

[@EmbraceMaking]

I'm not as familiar with lightburn but your motors might be "on" which means they will hold their current position. Are you running the latest D1 pro firmware? Might not be a lightburn issue as when I did a quick google search it comes up with this: forum.lightburnsoftware.com/t/disable-steppers/43986 ...

[@torowazup1]

Hi 👋 and Thank You for the best and great explanation and going beyond. Have you assembled a xtool D1 Pro with extension kit?

[@EmbraceMaking]

Hi Max, thank you so much! I have not tried the extension kit... although I have the rotary kit and need to make a video soon!

[@brianpacchetti5028]

Can't wait for future project and D1 upgrade.

[@EmbraceMaking]

Thank you, always more in the works ;)

[@charlesreicks648]

Sorry useing the Xtool d1 pro 20w machine and their software. Thanks

[@kerrybrophy2493]

The link to the cpap hose has been removed. Was there a problem with it? Do any of your add ons and products I can purchase void the warranty? I find your videos very helpful.

[@Moe_Z_]

Im trying to find the silicone mat and its not tagged, whats it called?

[@EmbraceMaking]

Hi Moe, here is the 20" x 28" mat: amzn.to/3zDyMG7 and this one is the 23.5" x 31.5" mat: amzn.to/3A0Fzv1 thanks!

[@josephdiazjd9]

Great Video! The manufacturer website mentions capabilities of offline processing/operating mode but no where does it say how to do this. Is it possible to load the job to the laser, disconnect from the computer and engrave offline? To run the same job multiple times without being connected to WiFi or USB connection.

[@EmbraceMaking]

Good question! I haven't tried it... but... I bet if you disconnect from the computer and just press the button at the front I believe it will automatically start the last job. Give that a try!

[@josephdiazjd9]

@@EmbraceMaking I tried it out and nothing happens. After disconnecting, the machine will not process the last job. It will give a pop up warning if machine is disconnected before pressing the start button on the machine as well. Using XCS and D1 pro 10w on PC.

[@user-qy9rg3nt2l]

Guess I need a laptop with this cutter. I was hoping for some sort of screen menu like my 3D printers.

[@EmbraceMaking]

What kinds of jobs are you looking to process? I believe you can slap files on the SD card and just press the button on the front and it may run the newest file on the card... I'd have to look into it. I recently did a video on the ORTUR laser master 3... check that one out. Although it's not a video showing how to use the machine, you will see in the video that the performance is comparable to the XTOOL as it is also 10W.... and with that one you can actually run the machine off an app on your phone. Again, I don't show that in my video but apparently its pretty easy to do

[@user-qy9rg3nt2l]

@@EmbraceMaking First, I appreciate your video. It really helped out, especially with the cable management. I see several places mine likes to snag. Just put my D1 Pro 20W with extension kit together yesterday, and spent several hours getting the hang of it. Looked around for SD/TF card utilization, but saw nothing. I moved my bulky desktop setup into my workshop just to get everything going. First project is 10" X 8" cope and drag boxes for sand casting. Designed the finger joints and am impressed with how well it cuts. Just have to fine tune the finger sizes for the kerf.

[@christophecastella9168]

Awesome cable management, it helped me ! thanks

[@EmbraceMaking]

Glad it helped! Thanks!

[@Piginhatwoodcrafts]

Great video! A few questions.. You don't show what is on the other end of the CPAP hose, what is that setup re removing fumes etc. Are you saying with your setup you don't need an enclosure at all? Thanks

[@EmbraceMaking]

Somewhere in the video I believe I put a link that pops up in the top right hand corner of the screen, but here is my other video showing the filtration system: kzbin.info/www/bejne/oWjUhXhqqZmmnJo My nozzle is geared more towards people who don't have room for the enclosure or are doing light work with their laser. I would recommend a full enclosure and professional filtration system for anyone running their laser for long periods of time or working with really nasty materials. The nozzle works great but realistically some smoke and fumes will still escape as it is impossible for it to get absolutely everything. An enclosure (in theory) captures everything since there is nowhere else for the fumes to go.

[@Piginhatwoodcrafts]

@@EmbraceMaking thanks for info ,👍

[@LaszloBagi]

The vacuum extractor looks fairly high up from the bottom of the laser. How well does it work?

[@EmbraceMaking]

Hi Laszlo, when developing this I tried multiple versions with the nozzle high and very low. When the nozzle is very low the vacuum strength is very powerful and can disturb light materials, or small workpieces. It actually starts to vacuum them off the table! So I kept iterating designs until there was no risk of moving small or thin parts but still close enough that the vacuum strength is powerful enough to draw in the fumes. So it is at a height that is a good balance for all general purpose. However, if you are the type of person who is not processing lighter materials, reach out to me on my website through the contact form and I can make you a custom length nozzle that is lower! Thanks!

[@LaszloBagi]

@@EmbraceMaking Great info! Thanks!

[@toddhoff3637]

Great video! Helped me make the decision to buy one, and will be following your video & recommendations! Any other suggestions for the CPAP hose, as your link above no longer works.

[@EmbraceMaking]

Thanks Todd! Right now Amazon appears to be temporarily out of stock so you might have to shop around for that piece off of Amazon unfortunately. I imagine it won't take them long to get them back though!