Yamaha 4 Stroke Outboard Motor, 50hp, How to replace the fuel filter.

Part 2 of an annual service on a 50hp 2014 Yamaha Four Stroke outboard motor. How to replace the fuel filter element. This filter had some water in it so you get to see an example of water in gas and how to identify it.
I probably mentioned it in the video, but just in case I didn't: The fuel filter should be replaced every year, we replace them at the beginning of the season.
Questions? please leave a comment or Contact us directly here: canadawidemari...
In this video we used:
Sierra 18-79799 fuel filter element: canadawidemari...
And as usual, if you are not quite sure what parts you need, contact us at the above link and we are happy to help.
Don't forget to subscribe,
and
Thanks for watching.

[@leonportelance9613]

No fluff, useful, straight forward info. Thank you

[@iFixJunk]

Liked, subscribed. Something I figured out after a long time and a lot of plier marks: That weird, circular cavity at the bottom of the fuel cup on the filter accepts the business end of some of my nut drivers. I like to get a nut driver that fits snugly in there and use it as a wrench to turn the cup. I do a lot of routine maintenance and preventative maintenance on Yamaha outboards and I have not regretted this method yet. I haven't found a tool for these smaller Yamaha fuel filters. Thought they'd have one like the 150-300 hp fuel filter tool, but I think I'm going to have to make something myself...

[@acme9538]

Thanks for the video. I have the same / similar filter on my F70 . . . I applied some silicone grease on those plastic threads today when I changed the filter. Hope it helps more than hurts, LOL.

[@CanadaWideMarine]

I have used silicone grease on the threads in the past, it helps a little on the tight threads, it has never been a problem, other than cleaning them well next time I take it apart.

[@bobkatbry]

There was a recall on the fuel twist on connector. Did you get that replaced? What does the new connection look like?

[@adamthommes3198]

Hey guys, thanks for the video. It’s very helpful. Do you have any information on the o2 sensors for a 2018 yamaha F40? More specifically, the location and how to clean them?

[@rjnish55]

What is that orange hose that connects to the VST? What is it for?

[@billtruax7363]

How do you change an oil water separator going to the engine?

[@Chris-ik7st]

I had the same issue with the too tight o-ring. i crushed my first fuel filter. anyone have any tips on this?

[@crispernator]

day mate do you think a fuel water seperator filter between the tank and the engine would have helped to stop this from happening ,i have always had one on my boats admitedley they were all two strokes .

[@CanadaWideMarine]

I don't remember what was happening in this video, but yes, absolutely, I always highly recommend a water separating fuel filter.

[@Doc.Holiday]

I have a big RACOR before mine with a drainable bowl. It’s overkill but cheap insurance.

[@eduardocortes-dv4lo]

Do i have to do fogging when i winterise the YAMAHA F50HETL 2022?

[@michaelbrasco]

Right beside the oil dip stick, there is a small tube that seems to wrap around. My tube is hanging, and one side does not seem to be plugged in. What is this tube, does this affect my motor starting? How do I plug it back in please?

[@CanadaWideMarine]

Hello Michael. If you can email me a photo of this tube tube [e-mail] I should be able to identify it and help you out.

[@Bottomfeederonfire]

My F 70 started pouring fuel when I removed the clear, plastic housing. I guess I need to install a in-line shut off switch.

[@CanadaWideMarine]

fuel tank was likely pressurized, you will want to check your venting.

[@brucekeeney3131]

Can't hear you

[@CanadaWideMarine]

Thanks for the feedback Bruce. Still learning how to make videos, I have a new microphone on its way for future vids. Thanks for watching even with the poor sound.

[@brucekeeney3131]

Yes Sir content was good thanks for the video!

[@AdventuresofHappyOurs]

These filter cups are a horrible design. Too hard to get on and off.

[@CanadaWideMarine]

Yes, they are very difficult.

[@AdventuresofHappyOurs]

@@CanadaWideMarine I found a wrench designed for them on Amazon. Going to give that a try.